Sensoriamento remoto hidroacústico no mapeamento de macrófitas aquáticas submersas

Macrófitas são importantes produtoras primárias do ecossistema aquático, e o desequilíbrio do ambiente pode ocasionar seu crescimento acelerado. Portanto, levantamentos de dados relacionados a macrófitas submersas são importantes para contribuir na gestão de corpos de água. Contudo, a amostragem dessa vegetação requer um enorme esforço físico. Nesse sentido, a técnica hidroacústica é apropriada para o estudo de macrófitas submersas. Assim, os objetivos deste trabalho foram avaliar os tipos de dados gerados pelo ecobatímetro e analisar como esses dados caracterizam a vegetação. Utilizou-se o ecobatímetro BioSonics DT-X acoplado a um GPS. A área de estudo é um trecho do Rio Uberaba, MG. A amostragem foi feita por meio de transectos, navegando de uma margem à outra. Depois de processar os dados, obteve-se informação a respeito de ocorrência de macrófitas submersas, profundidade, altura média das plantas, porcentagem da cobertura vegetal e posição. A partir desse conjunto de dados, foi possível extrair outras duas métricas: biovolume e altura efetiva do dossel. Os dados foram importados de um Sistema de Informação Geográfica e geraram-se mapas ilustrativos das variáveis estudadas. Além disso, quatro perfis foram selecionados para analisar a diferença entre as grandezas de representação de macrófitas. O ecobatímetro mostrou-se uma ferramenta eficaz no mapeamento de macrófitas submersas. Cada uma das medidas - altura do dossel, ECH ou biovolume - caracteriza de forma diferente a vegetação submersa. Dessa forma, a escolha do tipo de representação depende da aplicação desejada.

Influence of fluid volume variations on the calculated value of the left ventricular mass measured by echocardiogram in patients submitted to hemodialysis

The left ventricular mass (LVM) measurement is of major importance for renal patients, as ventricular hypertrophy is an important prognostic index. The echo-cardiogram of the ventricular mass is larger before than it is after hemodialysis, which can confuse data interpretation. The aim of this work is to study the influence of alterations in fluid volume on the variations in measurements of ventricular mass observed during the course of a hemodialysis. Sixteen patients with chronic renal insufficiency in hemodialysis were evaluated at the Dialysis Unit of the University Hospital-UNESP, Botucatu, São Paulo State. The left ventricular mass was calculated from echocardiograms taken before and after hemodialysis and simultaneous ultra-filtration (12 patients: UF GROUP) and before and after hemodialysis isovolemic phase with sequential ultra-filtration (10 patients: ISO GROUP). Six of these patients were submitted to measurements of left ventricular mass before and after hemodialysis in both isovolemic and simultaneous ultra-filtration procedures. In the UF group, there was significant reduction in the following parameters before and after dialysis: diastolic diameter from 54.0 +/- 6.0 mm to 45.6 +/- 7.6 mm; left ventricular mass from 342 +/- 114 g to 265 +/- 117 g; and its respective index (IMVE) from 214 +/- 68 g/m(2) to 168 +/- 71 g/m(2). The ISO group showed no statistically significant variation. The behavior of the variables of six patients submitted to both observations confirm these results. In conclusion, the variations in echocardiogram measurements of the left ventricular mass relating to hemodialysis appear to be induced by alterations of the volemic condition.

Comparação de diferentes métodos para medida do tamanho do infarto experimental crônico em Ratos

OBJETIVO: Avaliar as diferenças entre três métodos para medida do infarto experimental em ratos, em relação ao método tradicional. MÉTODOS: A área infartada por histologia (AREA), o perímetro interno da cavidade infartada por histologia (PER) e o perímetro interno por ecocardiograma (ECO) foram comparados ao método tradicional (análise histológica das circunferências epicárdicas e endocárdicas da região infartada - CIR). Utilizaram-se ANOVA de medidas repetidas, complementada com o teste de comparações múltiplas de Dunn, o método de concordância de Bland & Altman e o teste de correlação de Spearman. A significância foi p < 0,05. RESULTADOS: Foram analisados dados de 122 animais, após 3 a 6 meses do infarto. Houve diferença na avaliação do tamanho do infarto entre CIR e os outros três métodos (p < 0,001): CIR = 42,4% (35,9-48,8), PER = 50,3% (39,1-57,0), AREA = 27,3% (20,2-34,3), ECO = 46,1% (39,9-52,6). Assim, a medida por área resultou em subestimação de 15% do tamanho do infarto, enquanto as medidas por ecocardiograma e pelo perímetro interno por meio de histologia resultaram em superestimação do tamanho do infarto de 4% e 5%, respectivamente. em relação ao ECO e PER, apesar de a diferença entre os métodos ser de apenas 1,27%, o intervalo de concordância variou de 24,1% a -26,7%, sugerindo baixa concordância entre os métodos. em relação às associações, houve correlações estatisticamente significativas entre: CIR e PER (r = 0,88 e p < 0,0001); CIR e AREA (r = 0,87 e p < 0,0001) e CIR e ECO (r = 0,42 e p < 0,0001). CONCLUSÃO: Na determinação do tamanho do infarto, apesar da alta correlação, houve baixa concordância entre os métodos.

Remodelamento cardíaco: análise seriada e índices de detecção precoce de disfunção ventricular

FUNDAMENTO: A estenose aórtica supravalvar (EAo) é utilizada para o estudo da remodelação cardíaca (RC) por sobrecarga pressórica. Nesse modelo, não estão claramente estabelecidos o comportamento da RC desde a fase inicial, nem os melhores parâmetros para a identificação da disfunção ventricular. OBJETIVOS: 1) Caracterizar, precoce e evolutivamente, as modificações morfofuncionais durante a RC em ratos com EAo e 2) identificar o índice mais sensível para detecção do momento do aparecimento da disfunção diastólica e sistólica do ventrículo esquerdo (VE). MÉTODOS: Ratos Wistar foram divididos em dois grupos - controle (GC, n=13) e EAo (GEAo, n=24) - e estudados nas 3ª, 6ª, 12ª e 18ª semanas pós-cirurgia. Os corações foram analisados por meio de ecocardiograma (ECO). RESULTADOS: Ao final do experimento, as relações do VE, do ventrículo direito e dos átrios com o peso corporal final foram aumentadas no GEAo. O ECO mostrou que o átrio esquerdo sofreu uma remodelação significativa a partir da 6ª semana. No GEAo, a porcentagem de encurtamento endocárdico apresentou queda significativa a partir da 12ª semana e a porcentagem de encurtamento mesocárdico, na 18ª semana. A relação onda E e onda A (E/A) foi superior no GC em comparação ao GEAo em todos os momentos analisados. CONCLUSÕES: O ventrículo esquerdo dos ratos com EAo, durante o processo de remodelação, apresentou hipertrofia concêntrica, disfunção diastólica precoce e melhoria da função sistólica, com posterior deterioração do desempenho. Além disso, constatou-se que os índices ecocardiográficos mais sensíveis para a detecção da disfunção diastólica e sistólica são, respectivamente, a relação E/A e a porcentagem de encurtamento endocárdico.

Structural organization and thermal properties of the Sb2O3-SbPO4 glass system

The structural organization of Sb2O3-SbPO4 glasses has been studied by FTIR, Raman, P-31 MAS and spin echo NMR, Mossbauer and X-ray absorption spectroscopy (EXAFS and XANES at K and L-3,L-1-Sb edges). The combined results can be explained in terms of two potential mechanisms describing the change of the Sb(m) local environment upon incorporation of Q((4))-type phosphate. The formation of the latter species requires anionic compensation that may be adjusted by (a) formation of non bridging oxygen or (b) formation of SbO4E- groups (E = non-bonding electron pair). The second model is favored.

Structural studies of NaPO3-WO3 glasses by solid state NMR and Raman spectroscopy

Vitreous samples were prepared in the (100 2 x) NaPO3-x WO3 (0 <= x <= 70) glass forming system using conventional melting-quenching methods. The structural evolution of the vitreous network was monitored as a function of composition by thermal analysis, Raman spectroscopy and high resolution one- and two-dimensional P-31 solid state NMR. Addition of WO3 to the NaPO3 glass melt leads to a pronounced increase in the glass transition temperatures, suggesting a significant increase in network connectivity. At the same time Raman spectra indicate that up to about 30 mol% WO3 the tungsten atoms are linked to some non-bridging oxygen atoms (W-O- or W=O bonded species), suggesting that the network modifier sodium oxide is shared to some extent between both network formers. W-O- W bond formation occurs only at WO3 contents exceeding 30 mol%. P-31 magic angle spinning (MAS)-NMR spectra, supported by two-dimensional J-resolved spectroscopy, allow a clear distinction between species having two, one, and zero P-O-P linkages. The possible formation of some anionic tungsten sites suggested from the Raman data implies an average increase in the degree of polymerization for the phosphorus species, which would result in diminished P-31/Na-23 interactions. This prediction is indeed confirmed by P-31{Na-23} and Na-23{P-31} rotational echo double resonance (REDOR) NMR results, which indicate that successive addition of WO3 to NaPO3 glass significantly diminishes the strength of phosphorus-sodium dipole-dipole couplings.

Uterine evaluation and gestation diagnosis in owl monkey (Aotus azarai infulatus) using the B mode ultrasound

Background Gynecological and obstetrical ultrasonography has become an indispensable tool in the routine management, health evaluation and research on captive non-human primates.Methods Ultrasound was used to evaluate the uterus and estimate the gestation of owl monkeys. Twelve couples were selected, where five were primiparous and seven multiparous females from the National Primate Center reproductive colony, Ananindeua-PA, Brazil. The procedures were carried out using the GE (R) Logiq 100 MP, equipped with a 7.5 MHz linear probe.Results the females showed a simple uterus, of elongated shape, regular outline and homogeneous echogenic texture. In the uterine measurements craniocaudal diameter, dorsoventral diameter and uterine volume (UV), significant differences were identified (P < 0.05) between ultrasound examinations of primiparous and multiparous females. The UV showed a positive correlation with the number of births. The gestational sac and the embryonic echo were visible between 28 and 38 days after mating. Between 48 and 68 days after mating, embryonic death was identified in all the gestations.Conclusions the chemical (use of tranquilizers) and husbandry factors (capture stress) may be related to the prenatal death. The establishing methods of conditioning the female to the ultrasonographic exam may offer a solution to this problem.

Glasses in the SbPO4-WO3 system

Glasses in the binary system (100 - x)SbPO4-xWO3 (20 <= x <= 60, x in mol%) have been prepared and characterized. Differential thermal analysis (DTA) shows that the glass transition temperature, T-g increases from 412 degrees C, for samples containing 20 mol% of WO3 to 481 degrees C observed for glass containing 60 mol%. Sample containing 40 mol% in WO3 were observed to be the most stable against devitrification. The structural organization of the glasses has been studied by using Fourier transform infra-red (FTIR), Raman, P-31 Magic angle spinning (MAS) and spin echo nuclear magnetic resonance (NMR) spectroscopies. Results suggest two distinct networks comprising the glass structure, one with high SbPO4 content and the other characteristic of the highest WO3 content samples. The glasses present photochromic properties. Colour changes are observed for samples after exposure to ultraviolet or visible laser light. XANES, at L-1 absorption edge of tungsten, suggests partial reduction from W6+ to W5+ species during the laser irradiation. The photochromic effects and the colour changes, promoted by laser excitation, are reversible and easily removed by heat for during 1 h at 150 degrees C. Subsequent 'write/erase' cycles can be done without degradation of the glasses. (C) 2007 Elsevier B.V. All rights reserved.

Structural studies of NaPO3-MoO3 glasses by solid-state nuclear magnetic resonance and raman spectroscopy

Vitreous samples were prepared in the (100 - x)% NaPO3-x% MoO3 (0 <= x <= 70) glass-forming system by a modified melt method that allowed good optical quality samples to be obtained. The structural evolution of the vitreous network was monitored as a function of composition by differential scanning calorimetry (DSC), Fourier transform infrared spectroscopy (FT-IR), Raman scattering, and solid-state nuclear magnetic resonance (NMR) for P-31, Na-23, and Mo-95 nuclei. Addition of MoO3 to the NaPO3 glass melt leads to a pronounced increase in the glass transition temperatures up to x = 45, suggesting a significant increase in network connectivity. For this same composition range, vibrational spectra suggest that the Mo6+ ions are bonded to some nonbridging oxygen atoms (Mo-O- or Mo=O bonded species). Mo-O-Mo bond formation occurs only at MoO3 contents exceeding x = 45. P-31 magic-angle spinning (MAS) NMR spectra, supported by two-dimensional J-resolved spectroscopy, allow a clear distinction between species having two, one, and zero P-O-P linkages. These sites are denoted as Q(2Mo)((2)), Q(1Mo)((2)), and Q(0Mo)((2)), respectively. For x < 0.45, the populations of these sites can be described along the lines of a binary model, according to which each unit of MoO3 converts two Q(nMo)((2)) sites into two Q((n+1)Mo)((2)) sites (n = 0, 1). This structural model is consistent with the presence of tetrahedral Mo(=O)(2)(O-1/2)(2) environments. Indeed, Mo-95 NMR data suggest that the majority of the molybdenum species are four-coordinated. However, the presence of additional six-coordinate molybdenum in the MAS NMR spectra indicates that the structure of these glasses may be more complicated and may additionally involve sharing of network modifier oxide between the network formers phosphorus and molybdenum. This latter hypothesis is further supported by Na-23{P-31} rotational echo double resonance (REDOR) data, which clearly reveal that the magnetic dipole-dipole interactions between P-31 and Na-23 are increasingly diminished with increasing molybdenum content. The partial transfer of modifier from the phosphate to the molybdate network former implies a partial repolymerization of the phosphate species, resulting in the formation of Q(nMo)((3)) species and accounting for the observed increase in the glass transition temperature with increasing MoO3 content that is observed in the composition range 0 <= x <= 45. Glasses with MoO3 contents beyond x = 45 show decreased thermal and crystallization stability. Their structure is characterized by isolated phosphate species [most likely of the P(OMo)(4) type] and molybdenum oxide clusters with a large extent of Mo-O-Mo connectivity.

Is 44-hour better than 24-hour ambulatory blood pressure monitoring in hemodialysis?

The aim of this study is to evaluate if hemodialysis (HD) patients with similar blood pressure (BP) in the whole inter-HD period could have different target organ lesions and survival if the behavior of BP differs from the first to the second day of the inter-HD period. The present study compares 44-hour ambulatory BP monitoring (ABPM) patterns in 45 HD patients. Three BP patterns emerged: group A (n = 15) had similar BPs throughout (138 ± 11/88 ± 12 in the first 22 h vs. 140 ± 11/87 ± 12 mm Hg in the second 22-hour period); group B (n = 15) had a significant systolic BP rise from the first to the second period (132 ± 15/80 ± 12 vs. 147 ± 12/86 ± 13 mm Hg, p < 0.05); group C (n = 15) had significantly higher BPs (p < 0.05) than the other 2 groups throughout the whole inter-HD period, with no significant change between the 2 halves (172 ± 14/108 ± 12 vs. 173 ± 18/109 ± 14 mm Hg). Ventricular mass and survival during the 30-month follow-up period were statistically significantly better in group A, intermediate in group B and worse in group C. The data suggest that a 44-hour ABPM is more accurate than a 24-hour one in evaluating organ lesion and prognosis in HD patients. Copyright © 2006 S. Karger AG.

A study of the effect of overshooting deep convection on the water content of the TTL and lower stratosphere from Cloud Resolving Model simulations

Simulations of overshooting, tropical deep convection using a Cloud Resolving Model with bulk microphysics are presented in order to examine the effect on the water content of the TTL (Tropical Tropopause Layer) and lower stratosphere. This case study is a subproject of the HIBISCUS (Impact of tropical convection on the upper troposphere and lower stratosphere at global scale) campaign, which took place in Bauru, Brazil (22° S, 49° W), from the end of January to early March 2004. Comparisons between 2-D and 3-D simulations suggest that the use of 3-D dynamics is vital in order to capture the mixing between the overshoot and the stratospheric air, which caused evaporation of ice and resulted in an overall moistening of the lower stratosphere. In contrast, a dehydrating effect was predicted by the 2-D simulation due to the extra time, allowed by the lack of mixing, for the ice transported to the region to precipitate out of the overshoot air. Three different strengths of convection are simulated in 3-D by applying successively lower heating rates (used to initiate the convection) in the boundary layer. Moistening is produced in all cases, indicating that convective vigour is not a factor in whether moistening or dehydration is produced by clouds that penetrate the tropopause, since the weakest case only just did so. An estimate of the moistening effect of these clouds on an air parcel traversing a convective region is made based on the domain mean simulated moistening and the frequency of convective events observed by the IPMet (Instituto de Pesquisas Meteorológicas, Universidade Estadual Paulista) radar (S-band type at 2.8 Ghz) to have the same 10 dBZ echo top height as those simulated. These suggest a fairly significant mean moistening of 0.26, 0.13 and 0.05 ppmv in the strongest, medium and weakest cases, respectively, for heights between 16 and 17 km. Since the cold point and WMO (World Meteorological Organization) tropopause in this region lies at ∼ 15.9 km, this is likely to represent direct stratospheric moistening. Much more moistening is predicted for the 15-16 km height range with increases of 0.85-2.8 ppmv predicted. However, it would be required that this air is lofted through the tropopause via the Brewer Dobson circulation in order for it to have a stratospheric effect. Whether this is likely is uncertain and, in addition, the dehydration of air as it passes through the cold trap and the number of times that trajectories sample convective regions needs to be taken into account to gauge the overall stratospheric effect. Nevertheless, the results suggest a potentially significant role for convection in determining the stratospheric water content. Sensitivity tests exploring the impact of increased aerosol numbers in the boundary layer suggest that a corresponding rise in cloud droplet numbers at cloud base would increase the number concentrations of the ice crystals transported to the TTL, which had the effect of reducing the fall speeds of the ice and causing a ∼13% rise in the mean vapour increase in both the 15-16 and 16-17 km height ranges, respectively, when compared to the control case. Increases in the total water were much larger, being 34% and 132% higher for the same height ranges, but it is unclear whether the extra ice will be able to evaporate before precipitating from the region. These results suggest a possible impact of natural and anthropogenic aerosols on how convective clouds affect stratospheric moisture levels.

Batimetria fluvial estimada com dados orbitais: Estudo de caso no alto curso do rio Paraguai com o sensor ASTER

The Paraguay River is the main tributary of the Paraná River and has an extension of 1.693 km in Brazilian territory. The navigability conditions are very important for the regional economy because most of the central-west Brazilian agricultural and mineral production is transported by the Paraguay waterway. Increased sedimentation along the channel requires continuous dredging to waterway maintenance. Systematic bathymetric surveys are periodically carried out in order to check depth condition along the channel using echo-sounding devices. In this paper, digital image processing and geostatistical analysis methods were used to analyze the applicability of the ASTER sensor to estimate channel depths in a segment of the upper Paraguay River. The results were compared with field data in order to choose the band with better adjustment and to evaluate the standard deviation. Comparing the VNIR bands, the best fit was presented by the red wavelength (band 2; 0,63 - 0,69 μm), showing a good representation of the channel depths shallow than 1,7 m. Applying geostatistical methods, the model accuracy was enhanced from 43 cm to 36 cm and undesired components were slacked. It was concluded that the digital number of band 2, converted to bathymetry information allows a good estimation of river depths and channel morphology.

Submerged macrophytes height estimation by echosounder data sample

Traditional methods of submerged aquatic vegetation (SAV) survey last long and then, they are high cost. Optical remote sensing is an alternative, but it has some limitations in the aquatic environment. The use of echosounder techniques is efficient to detect submerged targets. Therefore, the aim of this study is to evaluate different kinds of interpolation approach applied on SAV sample data collected by echosounder. This study case was performed in a region of Uberaba River - Brazil. The interpolation methods evaluated in this work follow: Nearest Neighbor, Weighted Average, Triangular Irregular Network (TIN) and ordinary kriging. Better results were carried out with kriging interpolation. Thus, it is recommend the use of geostatistics for spatial inference of SAV from sample data surveyed with echosounder techniques. © 2012 IEEE.

Automatic microstructural characterization and classification using artificial intelligence techniques on ultrasound signals

Secondary phases such as Laves and carbides are formed during the final solidification stages of nickel based superalloy coatings deposited during the gas tungsten arc welding cold wire process. However, when aged at high temperatures, other phases can precipitate in the microstructure, like the γ″ and δ phases. This work presents a new application and evaluation of artificial intelligent techniques to classify (the background echo and backscattered) ultrasound signals in order to characterize the microstructure of a Ni-based alloy thermally aged at 650 and 950 °C for 10, 100 and 200 h. The background echo and backscattered ultrasound signals were acquired using transducers with frequencies of 4 and 5 MHz. Thus with the use of features extraction techniques, i.e.; detrended fluctuation analysis and the Hurst method, the accuracy and speed in the classification of the secondary phases from ultrasound signals could be studied. The classifiers under study were the recent optimum-path forest (OPF) and the more traditional support vector machines and Bayesian. The experimental results revealed that the OPF classifier was the fastest and most reliable. In addition, the OPF classifier revealed to be a valid and adequate tool for microstructure characterization through ultrasound signals classification due to its speed, sensitivity, accuracy and reliability. © 2013 Elsevier B.V. All rights reserved.

Inferência espacial para mapeamento de macrófitas submersas: estudo de caso

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)