Sintering of tin oxide processed by slip casting

Sintering of SnO 2 compacts, obtained through slip casting, was studied by means of dilatometry, Hg porosimetry, scanning electron microscopy, and density measurement (Archimedes method). Sintering is strongly influenced by the green microstructure. Moreover, the sintering mechanisms are not dependent on the slurries' solid content up to 50% of solids in volume. Above this value, agglomerates are formed, leading to differential sintering inside and among the agglomerates. Another important point is the reduction of the temperature of maximum shrinkage rate when compared to tin oxide processed by isostatic pressing. This reduction is more accentuated when ammonium hydroxide is added to the suspension. (C) 2000 Published by Elsevier Science Ltd. All rights reserved.

Efeito da densidade de plantas de Panicum maximum Jacq. sobre o crescimento inicial de Eucalyptus grandis W.Hill ex Maiden

In order to verify the effect of Panicum maximum plant density on the initial growth of Eucalyptus grandis plants, one assay was conducted under semi-controlled conditions of soil fertility and humidity. Dark red Latossol, collected from the arable layer, was used as substrate in 50 liters amianthus cement boxes. One seedling of Eucalyptus was planted in each box. Fifteen days later, seedlings of P. maximum were transplanted on the same box. The treatments consisted of 0, 4, 8, 12, 16 and 20 plants of P. maximum per m 2. The experimental design was the complete randomized design, with six treatments and eight replicates for P. maximum. One hundred and ten and 190 days after transplanting, Eucalyptus plants grown among P. maximum showed an average reduction of 30.80 and 46.55% stem diameter, 25.10 and 22.50 plant high, 40.18 and 31.29% stem dry weight, 61.32 and 54.06% branch dry weight, 53.72 and 51.82% root dry weight, 44.62 and 38.50% leaf dry weight, 22.51 and 23.16 branch number, 20.72 and 19.97% leaf number, and 33.88 and 17.05% leaf area, respectively.

Ultrasonic density measurement cell design and simulation of non-ideal effects

This paper presents a theoretical analysis of a density measurement cell using an unidimensional model composed by acoustic and electroacoustic transmission lines in order to simulate non-ideal effects. The model is implemented using matrix operations, and is used to design the cell considering its geometry, materials used in sensor assembly, range of liquid sample properties and signal analysis techniques. The sensor performance in non-ideal conditions is studied, considering the thicknesses of adhesive and metallization layers, and the effect of residue of liquid sample which can impregnate on the sample chamber surfaces. These layers are taken into account in the model, and their effects are compensated to reduce the error on density measurement. The results show the contribution of residue layer thickness to density error and its behavior when two signal analysis methods are used. (c) 2006 Elsevier B.V. All rights reserved.

Thermal characterization of an ultrasonic density-measurement cell

An ultrasonic density-measurement cell is experimentally characterized as a function of temperature. The measurement of propagation velocity and density of several liquids is performed in the 15 degrees C-40 degrees C temperature range. Results are compared to the tabulated values in the case of distilled water, showing an accuracy of 0.07% for the propagation velocity. The cell was tested with distilled water, alcohol, and homogenized milk, and density values are compared to those obtained with a pycnometer, showing 0.2% accuracy in density measurement for stabilized temperature and 0.4% accuracy under thermal gradient conditions.

Gravitational Energy-Momentum Density in Teleparallel Gravity

In the context of a gauge theory for the translation group, a conserved energy-momentum gauge current for the gravitational field is obtained. It is a true spacetime and gauge tensor, and transforms covariantly under global Lorentz transformations. By rewriting the gauge gravitational field equation in a purely spacetime form, it becomes the teleparallel equivalent of Einstein's equation, and the gauge current reduces to the Møller's canonical energy-momentum density of the gravitational field.

Comparação de métodos de determinação da gravidade específica de ovos de poedeiras comerciais

The objective of this work was to compare the results of measuring the specific gravity (SG) of laying hen eggs by using a weighing apparatus and the saline flotation method (SFM). Two hundred eggs from two genetic lines were distributed randomly into two groups of 50 eggs per genetic line and were submitted to two different sequences of SG measurement. Not significant differences were found between the two methods. The weighing apparatus measured the SG of the eggs accurately as the SFM.

Corn root length density and root diameter as affected by soil compaction and soil water content

Negative effects of soil compaction have been recognized as one of the problems restricting the root system and consequently impairing yields, especially in the Southern Coastal Plain of the USA. Simulations of the root restricting layers in green house studies are necessary for the development of mechanism which alleviates soil compaction problems in these soils. The selection of three distinct bulk densities based on the standard proctor test is also an important factor to determine which bulk density restricts the root layer. The experiment was conducted to assess the root length density and root diameter of the corn (Zea mays L.) crop as a function of bulk density and water stress, characterized by the soil density (1.2; 1.4, and 1.6 g cm -3), and two levels of the water content, approximately (70 and 90% field capacity). The statistical design adopted was completely randomized design, with four replicates in a factorial pattern of (3 × 2). The PVC tubes were superimposed with an internal diameter of 20 cm with a height of 40 cm (the upper tube 20 cm, compacted and inferior tube 10 cm), the hardpan with different levels of soil compaction were located between 20 and 30 cm of the depth of the pot. Results showed that: the main effects of subsoil mechanical impedance were observed on the top layer indicating that the plants had to penetrate beyond the favorable soil conditions before root growth was affected from 3.16; 2.41 to 1.37 cm cm -3 (P<0.005). There was a significant difference at the hardpan layer for the two levels of water and 90% field capacity reduced the root growth from 0.91 to 0.60 cm cm -3 (P<0.005). The root length density and root diameter were affected by increasing soil bulk density from 1.2 to 1.6 g cm -3 which caused penetration resistance to increase to 1.4 MPa. Soil water content of 70% field capacity furnished better root growth in all the layers studied. The increase in root length density resulted in increased root volume. It can also be concluded that the effect of soil compaction impaired the root diameter mostly at the hardpan layer. Soil temperature had detrimental effect on the root growth mostly with higher bulk densities.

Avaliação da distribuição da densidade em MDF a partir da técnica da onda de ultra-som

The goal of this research was to determine the density distribution in medium density fiberboard (MDF), manufactured with polyurethane derived from castor oil using, ultrasonic wave technique. The equipment used in this test is Steinkamp BP7 with plan and exponential transducers, both with 45 kHz frequencies, located in several zones on the plate in order to determine wave ultrasonic velocity. The Pinus caribaea and Eucalyptus grandis fiberboard were manufactured in the quality control and products development laboratory of Duratex with 500 mm long, 500 mm large, 8 and 15 mm of thickness. Three MDF for each fiber specimen and thickness were fabricated, totalizing twelve plates tested. The MDF were produced with 5% polyurethane addition, in temperature of 160°C, tension press of 53 bars and addition of moisture content of 12%. For determination of fiberboard density, samples were extracted from the same zones where the wave ultrasonic velocity was determined. In this case, DAX-Ray equipment was used. Statistical analysis shows good agreement with wave ultrasonic velocity and the density profile, validating the application of non-destructive technique in order to determine the density profile of MDF's.

Conversion between basic density and apparent density at any moisture content in Eucalyptus grandis

Wood basic density (BD) is related to other wood characteristics and its determination is important in forest inventory, though BD must be differentiated from the apparent density (AD), which relates to the moisture content (MC) of wood. The aim of this study is to demonstrate a reliable conversion from BD to AD for any MC of Eucalyptus grandis wood based on two exponential and linear models that relate volumetric shrinkage to MC. To this end, wood specimens were submitted to drying and the volumetric shrinkage was determined as a function of MC. The two models proved to be efficient in the conversion of BD to AD and vice versa.

Physical and mechanical properties of thermally modified wood from E. grandis

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Determination and padronization of normal values of bone mineral density (BMD) of the acessory carpus bone in young Thoroughbred horse using optical densitometry in radiographic image

Em 12 fêmeas e 12 machos da raça Puro Sangue Inglês com idade média de 12 meses, avaliou-se os valores normais da densidade mineral óssea do carpo acessório em milímetros de alumínio (mmAl) até o momento do fechamento completo da epífise distal do rádio, por meio do método de densitometria óptica em imagens radiográficas. A avaliação foi realizada por meio de um programa computacional (software) especialmente desenvolvido para medida de densidade óptica em filmes de raios-X, o qual contém a imagem radiográfica do osso carpo acessório, região de partes moles adjacente ao carpo acessório e os degraus de uma escala de alumínio (phatom), que permitiu a medida de densidade mineral óssea, sendo esta a média aritmética da região de interesse determinada no osso carpo acessório correspondente ao valor em milímetros da escala. Os valores da densidade mineral óssea em mmAl do acessório do carpo em função da idade não apresentaram diferenças entre os sexos (p=0,86) permitindo que uma equação de reta fosse ajustada para ambos os sexos (densidade mineral óssea (DMO) mmAl = 3.109 + 0,056 x idade em meses), na faixa etária estudada.

Effect of the levels of calcium and particle size of limestone on laying hens

O experimento foi realizado para avaliar o efeito dos níveis de cálcio (Ca) e da granulometria do calcário (GC) para poedeiras comerciais. Foram utilizadas 216 poedeiras da linhagem Dekalb White de 25 a 49 semanas de idade em um delineamento inteiramente casualizado, em esquema fatorial 3 × 2, composto de três níveis de cálcio (3,92; 4,02 e 4,12%) e duas granulometrias do calcário (fina - 0,60 mm; e grossa - 1,00 mm), que resultaram em seis tratamentos, com seis repetições de seis aves. Não houve efeito significativo dos níveis de cálcio e da granulometria do calcário nem da interação nível de cálcio × granulometria do calcário para o consumo de ração, o peso dos ovos, a gravidade específica, a espessura da casca, a porcentagem de casca, a unidade Haugh, a digestibilidade de cálcio e fósforo e a porcentagem do trato digestório. A produção, massa, conversão por massa e conversão por dúzia de ovos tiveram seus melhores resultados com 4,12% de cálcio na dieta. A porcentagem de moela e o consumo de ração observado às 15 h melhoraram com o aumento na granulometria do calcário de 0,60 para 1,00 mm. Houve efeito da interação entre nível de cálcio e granulometria do calcário para a resistência à quebra da tíbia, a densidade óssea, o comprimento do intestino delgado e o consumo de ração às 6, 9, 12, 18 e 21 h, respectivamente. Recomenda-se a adição de 4,12% de cálcio e calcário na granulometria grossa (1,00 mm) para melhor desempenho de poedeiras comerciais. Mais estudos são necessários para elucidar os mecanismos envolvidos na alteração do comportamento alimentar das poedeiras em resposta às mudanças nos níveis de cálcio e na granulometria do calcário das rações.

Propriedades des fisicas dos Arenitos Caiua.

The Caiua Sandstones, sedimentary Cretaceous rocks, have a grain specific gravity nearly that of quartz, its main mineralogical component. The remaining properties, such as the apparent dry density, apparent and effective porosity, water absorption and saturation voids, present high values, but decrease with depth. -from English summary

Preparation of 9.5/65/35 PLZT powders by organic precursor method

In this study the preparation of 9.5/65/35 PLZT ceramic powders were investigated. The powders with the formula Pb0.905La0.095(Zr0.65 Ti0.35)0.976O3 + 3.5 w% PbO were prepared using Pechini process and partial oxalate method. The powder phase formation, powder morphology, and green density of PLZT were shown.

Modelo de otimização para seleção de árvores matrizes de Eucalyptus grandis

Individual data of basic density and volume of wood, pulp kappa number, soluble lignin, cost of pulping process as well as gravimetric gross yield of pulping process were used from 64 trees of Eucalyptus grandis W. Hill ex Maiden from a commercial population at Lençóis Paulista, SP. The Eucalyptus grandis's seeds were originally from a Seed Production Area (SPA) of Duratex S/A at Botucatu, SP. Obtained data were quantified considering objective of maximization no-bleaching pulp and volume and mass wood restriction, mass of residual and soluble lignin, planted area and pulping process cost. it has also been aimed a selection method for matrix trees through mathematical programming techniques. Obtained strategy maximized the economical result, selected matrix trees and followed all limits of technological and organizing productivities imposed by the company. It also aimed the production of no-bleaching pulp within the planned time.