Tide-topography interaction along the eastern Brazilian shelf

In the Tropics, continental shelves governed by western boundary currents are considered to be among the least productive ocean margins in the world, unless eddy-induced shelf-edge upwelling becomes significant. The eastern Brazilian shelf in the Southwest Atlantic is one of these, and since the slight nutrient input from continental sources is extremely oligotrophic. It is characterized by complex bathymetry with the presence of shallow banks and seamounts. In this work, a full three-dimensional nonlinear primitive equation ocean model is used to demonstrate that the interaction of tidal currents and the bottom topography of the east Brazil continental shelf is capable of producing local upwelling of South Atlantic Central Water, bringing nutrients up from deep waters to the surface layer. Such upper layer enrichment is found to be of significance in increasing local primary productivity. (c) 2005 Elsevier Ltd. All rights reserved.

Efeitos ambientais da disposição oceânica de esgotos por meio de emissários submarinos: Uma revisão

Oceanic disposal systems of domestic sewage, or submarine sewage outfalls, have been historically used around the world as a solution for urban effluents, in special due to economic aspects. However, release into the ocean, in shallow or deep waters, may induce a set of negative environmental impacts, as eutrophication, toxic algal blooms, pathogenic microorganisms introduction and contamination by chemical substances which are capable of causing toxic effects to the biota and bioaccumulation. Thus, the release of untreated sewage into the sea does not constitute an adequate environmental practice; then, urban effluents should be treated in order to remove nutrients, contaminants and pathogenic organisms and avoid environmental degradation.

Análise microestrutural de tubos API P110, para prospecção de petróleo e gás, soldados pelo processo HF/ERW

On the grounds of the great advances achieved over recent years, the process HF/ERW (High-Frequency/Electric Resistance Welding)welded pipe have played an active role in the oil and gas industry for deep water applications, at high and extremely low temperatures, under high pressure and in highly corrosive environments, gradually replacing manufactured pipes by other processes. However, studies have shown that defects in the welded joints are a the leading causes of pipelines failures, which has required the determination of toughness values in this region, in compliance with the strict recommendations of the codes and standards with manufacturers and construction companies, on the oil and gas sector. As part of the validation process required toughness values, this research project focuses on a microstructural analysis in HF / ERW tubes microalloyed, steel grade API 5CT P110, designed to explore oil and gas in deep waters, the subject of strategic relevance to the country because of the recent discoveries in the Santos mega fields: Tupi and Libra (pre-salt). In this scientific work will be presented and discussed the results of mechanical tensile and Charpy, a few CTOD tests curves (showing the trend of toughness values to be obtained), and the microstructures of the base material obtained by optical microscopy, with special emphasis on the formation of nonmetallic inclusions in the welded joint

Water mass reconstruction by Nd isotopic analysis from Mid Atlantic oceanic sediments

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Estudo do comportamento em fadiga de um tubo de aço API 5CT soldado por resistência elétrica

The oil extraction in deep waters sparked new areas of knowledge, the creation of engineering courses dedicated just to these processes and a wide field of analysisvoiding multiple impacts in case of faults, mainly the economic and environmental. This paper aims to show on the effects and causes of fatigue failure in steel tubes used for oil and gastransportation (linepipe), mainly caused by vortex induced vibrations, or VIV. To make this, through laboratory tests, it found trough the curve Stress versus Number of Cycles, and thus estimating that with a stress value of 350 MPa or less, the fatigue life cycle of the API 5CT T95 (1% Cr) pipe is estimated infinite. It could conclude that the analyzed material has good fatigue failure resistance for offshore use, taking into account only the influence of VIV's, since there are no stress concentrators

Análise microestrutural de tubos API N80 soldados pelo processo HF/ERW para prospecção de petróleo e gás

On the grounds of the great advances achieved over recent years, the process HF/ERW (High-Frequency/Electric Resistance Welding)welded pipe have played an active role in the oil and gas industry for deep water applications, at high and extremely low temperatures, under high pressure and in highly corrosive environments, gradually replacing manufactured pipes by other processes. However, studies have shown that defects in the welded joints are a the leading causes of pipelines failures, which has required the determination of toughness values in this region, in compliance with the strict recommendations of the codes and standards with manufacturers and construction companies, on the oil and gas sector. As part of the validation process required toughness values, this research project focuses on a microstructural analysis in HF / ERW tubes microalloyed, steel grade API 5CT N80, designed to explore oil and gas in deep waters, the subject of strategic relevance to the country because of the recent discoveries in the Santos mega fields: Tupi and Libra (pre-salt). In this scientific work will be presented and discussed the results of mechanical tensile and Charpy, a few CTOD tests curves (showing the trend of toughness values to be obtained), and the microstructures of the base material obtained by optical microscopy, with special emphasis on the formation of non-metallic inclusions in the welded joint

Características do aço API X70 utilizado em tubos de transporte de petróleo e gás

Having in mind that petroleum's history presents a huge growth, the exploration and production areas have been receiving lots of investments, in order to attend the increasing demand for gas and petroleum. Looking through that scenario, new technologies have been evolving in favor of discovering new natural petroleum deposits and act with effectiveness in truly deep waters without giving up the worldwide best operational security practices. The use of rigid pipes in marine installations have been rising quickly and, thanks to this reality, the many storage and pipe launching forms became study objects and are getting improved. The analysis of steel API X70 characteristics, proving that they are suitable for use in pipes developed to transport gas and petroleum is the theme of this presentation. A tensile test was conducted to determine the base metal's mechanical properties, draining's tension, traction's resistance, elasticity's modulus and maximum tension. An aspect that is concerning too is the metallographic analysis, in order to determine the studied iron's microstructure. Results of analyzes showed that the steel has high resistance, with good capacity for deformation and well defined yield point, concluding suitable for the application in question

Da fonte à bacia: interação continente-oceano no sistema sedimentar Rio São Francisco, Brasil

Pós-graduação em Geociências e Meio Ambiente - IGCE