Characterization of curaua fiber

This paper describes the chemical, thermal and thermomechanical characterization of curaua fiber. The research of the thermal and thermomechanical properties of natural fibers is of major interest, considering their increasing utilization in several applications, and the large temperature range to which the fibers are submitted.

Hybridization effect on the mechanical properties of curaua/glass fiber composites

The aim of this paper was to evaluate the effect of hybridizing glass and curaua fibers on the mechanical properties of their composites. These composites were produced by hot compression molding, with distinct overall fiber volume fraction, being either pure curaua fiber, pure glass fiber or hybrid. The mechanical characterization was performed by tensile, flexural, short beam, Iosipescu and also nondestructive testing. From the obtained results, it was observed that the tensile strength and modulus increased with glass fiber incorporation and for higher overall fiber volume fraction (%Vf). The short beam strength increased up to %Vf of 30 vol.%, evidencing a maximum in terms of overall fiber/matrix interface and composite quality. Hybridization has been successfully applied to vegetable/synthetic fiber reinforced polyester composites in a way that the various properties responded satisfactorily to the incorporation of a third component. © 2013 Published by Elsevier Ltd. All rights reserved.

Analysis of curaua/glass hybrid interlayer laminates

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Influência da Espessura nas Propriedades Mecânicas de Compósitos Híbridos Interlaminares de Curauá/Vidro/Poliéster

The interest in the use of vegetable fibers (e.g. jute, sisal and curaua) for more noble applications, such as reinforcement in polymeric composite materials, has increased over the years due to a variety of aspects, especially those related to environmental legislation and community awareness regarding the life cycle of products. In this context, the aim of this work is to develop hybrid interlaminate curaua/glass/insaturated polyester composites by hot compression molding and to analyze their mechanical properties as a function of the thickness of the laminate. The short beam strength of the thickest sample decreased due to its higher void content. Furthermore, the thinnest sample showed lower hardness, and lower impact, tensile and Iosipescu shear strength, partly attributed to its lower fiber volumetric fraction. Thus, in general, the most adequate laminate was the one comprising eight layers, four of which were of glass fiber and four of curaua fiber, but only if flexural loading is not critical.

Ionized-air-treated curaua fibers as reinforcement for phenolic matrices

Curaua fibers were treated with ionized air to improve the fiber/phenolic matrix adhesion.The treatment with ionized air did not change the thermal stability of the fibers. The impact strength increased with increase in the fiber treatment time. SEM micrographs of the fibers showed that the ionized air treatment led to separation of the fiber bundles. Treatment for 12 h also caused a partial degradation of the fibers, which prompted the matrix to transfer the load to a poorer reinforcing agent during impact, thereby decreasing the impact strength of the related composite. The composites reinforced with fibers treated with ionized air absorbed less water than those reinforced with untreated fibers.

Natural fiber reinforced unsaturated polyester composites - An approach on compression molding

This work has been performed at Tapetes Sao Carlos-Brazil with the cooperation of the DaimlerChrysler Research Center Team in Ulm - Germany. The objective of the present paper is to report the results obtained with natural fiber reinforced unsaturated polyester (UP) composites, concerning surface quality measurements. The fibers that have been chosen for this work were sisal and curaua. The samples were produced by compression molding technique and afterwards submitted to three different tests, namely: a) thermal aging; b) water absorption and c) artificial weathering. The surface parameters measured before and after the tests were gloss, haze, short and long-waviness. The results have shown that after the tests there is a high loss of gloss, a high increase in haze, and a high increase in short and long-waviness as well. Curaua reinforced composites had a slightly better behavior when compared with sisal reinforced composites. The effect of the presence of filler and the addition of thermoplastic polyester (TP) on the material behavior has not been evidently detected. This result shows that the conventional technology/methods applied to UP-Fiberglass systems cannot be transferred to natural fibers without any modification. The fiber-matrix interaction and its response to the presence of additives must be fully understood before a successful processing route can be developed for painted natural fibers reinforced UP. Copyright © 2001 Society of Automotive Engineers, Inc.

Analysis of the four wave mixing effect (FWM) in a dispersion decreasing fiber (DDF) for a WDM system

We did a numerical investigation of the propagation of short light pulses in the region of 1.55 mu m and the conversion efficiency (CE) for the four wave mixing generation (FWM) of ordinary and dispersion decreasing fibers for use in wavelength division multiplexing (WDM) systems, Our simulations studies three different profiles, linear, hyperbolic. and constant, One conclude that for all the profiles there is decrease of the conversion efficiency with the increase in the channel separation. The hyperbolic profile present a higher efficiency of around 1000 above in magnitude compared with the others profiles at 0.2 nm of channel separation. We calculate the conversion efficiency versus the fiber length for the three profiles. The conversion efficiency for the hyperbolic profile is higher when compared to the constant and linear profiles. The other interesting point of the hyperbolic profile is that the increase of the CE in the beginning of the fiber does not show my oscillation in the CE value (log eta), which was observed for the constant and linear profiles. For all the profiles there is an increase of the conversion efficiency with the increase of the pump power. The compression factor C-i for the generated FWM signal at omega(3) was measured along the DDF's and the constant profile fibers. One can conclude that with the use of decreasing dispersion profile (DDF) fibers one can have a control of the (CE) conversion efficiency and the compression factor of the four wave mixing (FWM) generation in WDM systems. (c) 2005 Elsevier B.V. All rights reserved.

Natural fibers based composites - Technical and social issues

Brazil is the only country in South America to have an automotive supplier sector based on natural fibers. New opportunities are arising due to an increase demand by the car makers in applying natural fibers in their parts. Several crop fibers have been developed in Brazil. Among them can be listed caroa, piacava, pupunha, mutum and others of regional application. For the automotive industry, which requires large quantities with uniform quality, the alternatives are sisal (170,000 ton/yr), curaua (150 ton/yr in 2003), malva, 200 ton/yr; Brazil is the single largest producer country of sisal, and commercially, the only one in curaua. For South America, the alternatives are fique in Colombia, abaca in equator, flax in Argentina and curaua in Venezuela. It must be understood by the target countries of drugs, is that crop fiber can be an economic alternative to coca in the Andes region, therefore an instrument of land reform and drug reduction plantations. Several companies have a strong program of apply natural fibers based components in their products: Volkswagen do Brazil, DaimlerChrysler, General Motors do Brazil. Among their suppliers can be listed companies such Pematec (curaua), Toro (sisal, coir and jute), Incomer (sisal and jute), Ober (jute, curaua), Indaru (jute and sisal), Antolin (imported kenaf,) Tapetes Sao Carlos (sisal), Poematec (coir) and Art-Gore, with Woodstock'' wood and natural fibers). Figures about production and demand are discussed in the paper.

Accumulation of nutrients in sweet peppers cultivated in coconut fiber

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Digestive and functional properties of a partially hydrolyzed cassava solid waste with high insoluble fiber concentration

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Growth analysis of sweet pepper cultivated in coconut fiber in a greenhouse

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Determination of crude protein, crude fiber and crude fat in twenty-five genotypes of kale (B-oleracea var. acephala)

The aim of the study was to determine the percentage of crude protein, crude fiber and crude fat (ether extract) of 25 genotypes of kale from the Germplasm Bank of Instituto Agronomico de Campinas and of one genotype grown in the region of Jaboticabal-SP. The plants were cultivated in the field, and the leaves after collection were pre-dried in a convection oven at 65 degrees C for 72 h. Afterward, the leaves were analyzed for crude protein, crude fiber and crude fat (ether-soluble materials). Significant differences were detected among the different genotypes for all the characteristics examined. of the genotypes studied, six showed more than 30% crude protein: HS-20 (32.56%), Comum (31.70%), Couve de Arthur Nogueira 2 (31.16%), Pires 2 de Campinas (30.63%), Manteiga 1-916 (30.36%), and Manteiga de Ribeirao Pires I-2446 (30.03%). In relation to crude fiber, the highest percentage was seen in the genotype Manteiga de Mococa (10.92%), differing significantly from the other genotypes studied. With regard to crude fat, the highest percentage was found in the genotype HS-20 (3.72%), and Pires 1 de Campinas (3.34%). of the genotypes tested, HS-20 stood out among the others, showing both the highest percentage of protein and fat.

Small intestine development of laying hens fed different fiber sources diets and crude protein levels

The objective of the presente study was to evaluate the effects on different dietary fiber sources and crude protein levels on the intestinal morphometry of commercial layers. Isa Brown® layers with 48 weeks of age were distributed in a completely randomized experimental design with a 3 x 2 + 1 factorial arrangement, resulting in seven treatments with seven replicates of eight birds each. At the end of the fourth experimental period (28 days each), birds were 64 weeks of age and were randomly chosen (two birds per replicate, totaling 14 birds per treatment), weighed and sacrificed by neck dislocation. Their intestine was dissected and the duodenum, jejunum and ileum were collected for subsequent analysis of intestinal morphometry. Treatments consisted of diets containing three different fiber sources (cottonseed hulls, soybean hulls or rice husks) and two crude protein levels (12% or 16%). Soybean hulls and 16% crude protein level promoted, in general, an increase in villus height and crypt depth in the three intestinal segments. In the duodenum, the control diet resulted in higher villus height and crypt depth relative to the diets containing fiber. In the jejunum, higher crypt depth values. In the ileum, dietary fiber increased villus height as compared to the control diet.

Fiber sources in diets for newly weaned piglets

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)