Colour change of soft denture liners after storage in coffee and coke

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Peel bond strength of resilient liner modified by the addition of antimicrobial agents to denture base acrylic resin

In order to prolong the clinical longevity of resilient denture relining materials and reduce plaque accumulation, incorporation of antimicrobial agents into these materials has been proposed. However, this addition may affect their properties. Objective: This study evaluated the effect of the addition of antimicrobial agents into one soft liner (Soft Confort, Dencril) on its peel bond strength to one denture base (QC 20, Dentsply). Material and Methods: Acrylic specimens (n=9) were made (75x10x3 mm) and stored in distilled water at 37 degrees C for 48 h. The drug powder concentrations (nystatin 500,000U - G2; nystatin 1,000,000U - G3; miconazole 125 mg - G4; miconazole 250 mg - G5; ketoconazole 100 mg - G6; ketoconazole 200 mg - G7; chlorhexidine diacetate 5% - G8; and 10% chlorhexidine diacetate - G9) were blended with the soft liner powder before the addition of the soft liner liquid. A group (G1) without any drug incorporation was used as control. Specimens (n=9) (75x10x6 mm) were plasticized according to the manufacturers' instructions and stored in distilled water at 37 degrees C for 24 h. Relined specimens were then submitted to a 180-degree peel test at a crosshead speed of 10 mm/min. Data (MPa) were analyzed by analysis of variance (alpha=0.05) and the failure modes were visually classified. Results: No significant difference was found among experimental groups (p=0.148). Cohesive failure located within the resilient material was predominantly observed in all tested groups. Conclusions: Peel bond strength between the denture base and the modified soft liner was not affected by the addition of antimicrobial agents.

Evaluation of hardness and color stability in the soft lining materials after thermocycling and chemical polishing.

The aim of this study was to evaluate the Shore A hardness and color stability of two soft lining materials after thermocycling and when chemical polishing was used or omitted. Two acrylic-based soft lining materials were tested: Coe-Soft and Soft Confort, 14 specimens were made for each material. They were distributed in four groups according to the treatment performed. The specimens were thermocycled (1000 cycles) and half of the group submitted to chemical polishing (methyl methacrylate). Shore A hardness was determined and color stability was calculated by means of Commission International de l'Eclairage Lab uniform color scale using a spectrophotometer, the measurements were made immediately after deflasked, chemical polishing and thermocycling. Analysis of variance (ANOVA) and Tukey's tests were performed at p < 0.01. Color changes (deltaE) were observed after thermocycling in both soft lining materials: Soft Confort (10.60) showed significantly higher values than Coe-Soft (4.57). Coe-Soft (26.42) showed higher Shore A hardness values than Soft Confort (19.42). Chemical polishing did not influence in the color stability of both materials; however, influenced in the hardness values of Coe-Soft.

Comparação entre a percepção e a normatização sobre a iluminação em ambientes ocupacionais: estudo de caso em uma empresa florestal

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Comportamento do pedestre e ambiente térmico urbano

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Racionalização da energia elétrica com aplicação da legislação tarifária em indústria de embalagem plástica

Pós-graduação em Agronomia (Energia na Agricultura) - FCA

Avaliação da resistência de união ao cisalhamento, de diferentes sistemas adesivos à dentina. Análise em MEV do infiltrado resinoso

Pós-graduação em Ciências Odontológicas - FOAR

Trabalho de teleatendente: proposta de um protocolo de avaliação ergonômica

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Análise ergonômica do ambiente de trabalho para operadores de tratores e colhedoras agrícolas

Pós-graduação em Agronomia (Energia na Agricultura) - FCA

Micropartículas lipídicas sólidas obtidas por spray drying para liberação intraocular de ibuprofeno

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Usabilidade, percepção estética e força de preensão manual: influência no design ergonômico de instrumentos manuais : um estudo com tesouras de poda

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Dinâmica não linear e projeto de controle em sistemas de transporte vertical: comportamentos periódicos e caóticos

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Consultório odontológico: uma AET utilizando-se da EWA

This work tells the first steps of a larger project, that has for objective to develop the ergonomic evaluation of clinics odontologics installed in the Basic Units of Health of the municipal districts from São Paulo of São José dos Campos and Bauru. It is looked for to the end of the work to have characterized them, making possible like this the analysis in the way as it happens the interface among the users, equipments and atmosphere. For so much some will be used methodologies consecrated in the international scenery. It is told the results obtained with the first developed analysis, as test equal calibration of the chosen methodologies, as well as determination of procedures and worn-out times, for planning of the process.

Ambiente térmico y el bienestar de los cerdos en el período de descanso previo al sacrificio

The research aimed to evaluate the relationship between the thermal environment of the rest pens in a pig slaughterhouse and the surface temperature (ST) of the animals as well as the effect of intermittent water spraying on thermal comfort. There were two visits to slaughter industrial being in each selected three pens of rest, one for control treatment (no spray throughout the period) and two for the treatment of intermittent spraying water (30 minutes intervals with constant spray followed by 30 minutes then turned off). Assessments began at the time of discharging animals in which are taken the thermographic images from lots using an infrared thermographic camera. After housing in the pens, were registered the thermographic images and the respiratory frequency (RF) every five minutes for four hours. Were evaluated the temperature, relative humidity and temperature-humidity index (THI). Considering the values of THI was observed that the animals remained in a condition of comfort only at the time of his arrival at the slaughterhouse. The ST and RF of the animals kept in the pens without sprinkler system (control) showed a linear increase in function of time of day, with increasing temperature. The treatment with intermittent sprinkling of water was observed oscillatory behavior of the ST and RF, however it was always lower than the control treatment, even in times when the water sprinklers were turned off. The time required of spray to reduction and stabilization of the ST of the animals was limited to the combination of temperature and relative humidity, being estimated at 25 minutes at times of higher THI. The maximum environmental temperature during evaluation was 28.4 oC.

Conforto térmico em cidades de porte médio no oeste paulista: os casos de Presidente Prudente e Marília

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)