Caracterização espectral de áreas de gramíneas forrageiras infectadas com a doença mela-das-sementes da braquiária por meio de imagens CCD/CBERS-2

Imagens CCD/CBERS-2, nas bandas espectrais CCD2, CCD3 e CCD4, dos anos de 2004 e 2005, de Mirante do Paranapanema - SP, foram transformadas em reflectância de superfície usando o modelo 5S de correção atmosférica e normalizadas radiometricamente. O objetivo principal foi caracterizar espectralmente áreas de pastagens de Brachiaria brizantha em fase de florescimento, isentas e infectadas com a doença mela-das-sementes da braquiária, possibilitando a sua detecção por meio da comparação entre os valores de reflectância de superfície denominada de Fator de Reflectância Bidirecional de Superfície (FRBS). Teve-se, também, o objetivo de avaliar a eficácia das imagens CCD/CBERS-2 para a obtenção de respostas espectrais de pastagens. Os dosséis sadios e doentes da Brachiaria brizantha foram identificados por meio da análise dos valores de reflectância e dos dados observados no Índice de Estresse Hídrico Acumulativo Relativo da Cultura (ACWSI) obtidos na área de estudo. Os resultados indicaram que as principais diferenças foram a diminuição da reflectância na banda CCD3 e o aumento da reflectância na banda CCD4 nas áreas doentes. A metodologia empregada com o uso de dados do sensor CCD/CBERS-2, associados ao ACWSI, mostrou-se eficaz para discriminar dosséis infectados com a mela-das-sementes da braquiária.

Bundle Block Adjustment of CBERS-2B HRC Imagery Combining Control Points and Lines

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Orientação de imagens CBERS-2B usando o modelo rigoroso de colinearidade com dados orbitais

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Orientação semi-automática de imagens CBERS usando rodovias como controle de campo

In this paper is proposed a methodology for semiautomatic CBERS image orientation using roads as ground control. It is based on an iterative strategy involving three steps. In the first step, an operator identifies on the image the ground control roads and supplies along them a few seed points, which could be sparsely and coarsely distributed. These seed points are used by the dynamic programming algorithm for extracting the ground control roads from the image. In the second step, it is established the correspondences between points describing the ground control roads and the corresponding ones extracted from the image. In the last step, the corresponding points are used to orient the CBERS image by using the DLT (Direct Linear Transformation). The two last steps are iterated until the convergence of the orientation process is verified. Experimental results showed that the proposed methodology was efficient with several test images. In all cases the orientation process converged. Moreover, the estimated orientation parameters allowed the registration of check roads with pixel accuracy or better.

Exterior orientation of CBERS-2B imagery using multi-feature control and orbital data

The major contribution of this paper relates to the practical advantages of combining Ground Control Points (GCPs), Ground Control Lines (GCLs) and orbital data to estimate the exterior orientation parameters of images collected by CBERS-2B (China-Brazil Earth Resources Satellite) HRC (High-resolution Camera) and CCD (High-resolution CCD Camera) sensors. Although the CBERS-2B is no longer operational, its images are still being used in Brazil, and the next generations of the CBERS satellite will have sensors with similar technical features, which motivates the study presented in this paper. The mathematical models that relate the object and image spaces are based on collinearity (for points) and coplanarity (for lines) conditions. These models were created in an in-house developed software package called TMS (Triangulation with Multiple Sensors) with multi-feature control (GCPs and GCLs). Experiments on a block of four CBERS-2B HRC images and on one CBERS-2B CCD image were performed using both models. It was observed that the combination of GCPs and GCLs provided better bundle block adjustment results than conventional bundle adjustment using only GCPs. The results also demonstrate the advantages of using primarily orbital data when the number of control entities is reduced. © 2013 International Society for Photogrammetry and Remote Sensing, Inc. (ISPRS).

Análise da reconstrução 3D a partir de um par estereoscópico HR-CCD/CBERS-2 usando dois modelos matemáticos

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Orientação semi-automática de imagens CBERS usando rodovias como controle de campo

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Desenvolvimento de um programa computacional para classificação do uso da terra em imagens CBERS 2

Pós-graduação em Agronomia (Energia na Agricultura) - FCA

Temporal analysis of the reduction in gas emission in areas of mechanically-harvested sugarcane using satellite imagery

The primary objective of this study was to estimate the amount of gas not emitted into the air in areas cultivated with sugarcane (Saccharum officinarum) that were mechanically harvested. Satellite images CBERS-2/CCD, from 08-13-2004, 08-14-2005, 08-15-2006 and 08-16-2007, of northwestern São Paulo State were processed using the Geographic Information System (GIS)-IDRISI 15.0. Areas of interest (the mechanically-harvested sugarcane fields) were identified and quantified based on the spectral response of the bands studied. Based on these data, the amount of gas that was not emitted was evaluated, according to the estimate equation proposed by the Intergovernmental Panel on Climate Change (IPCC). The results of 396.65 km(2) (5.91% for 2004); 447.56 km(2) (6.67% for 2005); 511.54 km(2) (7.62% in 2006); and 474.60 km(2) (7.07% for 2007), calculated from a total area of 6,710.89 km(2) with sugarcane, showed a significant increase of mechanical harvesting in the study area and a reduction of gas emissions of more than 300,000 t yr(-1).

DETERMINATION of THE INDIRECT ORIENTATION of ORBITAL PUSHBROOM IMAGES USING CONTROL STRAIGHT LINES

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Detection and thinning of edges in previously known directions

This work presents a study on the generation of digital masks aiming at edge detection with previously known directions. This solution is important when edge direction is available either from a direction histogram or from a prediction based on camera and object models. A modification in the non-maximum suppression method of thinning is also presented enabling the comparison of local maxima for any edge directions. Results with a synthetic image and with crops of a CBERS satellite images are presented showing an example with its application in road detection, provided that directions are previously known.

Projections Onto Convex Sets through Particle Swarm Optimization and its application for remote sensing image restoration

Image restoration attempts to enhance images corrupted by noise and blurring effects. Iterative approaches can better control the restoration algorithm in order to find a compromise of restoring high details in smoothed regions without increasing the noise. Techniques based on Projections Onto Convex Sets (POCS) have been extensively used in the context of image restoration by projecting the solution onto hyperspaces until some convergence criteria be reached. It is expected that an enhanced image can be obtained at the final of an unknown number of projections. The number of convex sets and its combinations allow designing several image restoration algorithms based on POCS. Here, we address two convex sets: Row-Action Projections (RAP) and Limited Amplitude (LA). Although RAP and LA have already been used in image restoration domain, the former has a relaxation parameter (A) that strongly depends on the characteristics of the image that will be restored, i.e., wrong values of A can lead to poorly restoration results. In this paper, we proposed a hybrid Particle Swarm Optimization (PS0)-POCS image restoration algorithm, in which the A value is obtained by PSO to be further used to restore images by POCS approach. Results showed that the proposed PSO-based restoration algorithm outperformed the widely used Wiener and Richardson-Lucy image restoration algorithms. (C) 2010 Elsevier B.V. All rights reserved.

The Impact on Geographic Location Accuracy due to Different Satellite Orbit Ephemerides

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Desenvolvimento da Tecnologia de Soldagem do Titânio pelo Processo TIG Orbital no Segmento Aeroespacial Brasileiro - Parte 2: Caracterização das Juntas Soldadas

In this work, three welding programs for orbital TIG previously developed were used, using pulsed current and increasing speed (M), constant current (#B) and pulsed current and decreasing current (#C). One of those should be used for the propulsion system of the satellite CBERS (CHINA-BRAZIL EARTH RESOURCES SATELLITE). Welded joints using tubes of commercially pure titanium were obtained with these procedures, which were characterized by means of mechanical and metallographic tests. The obtained results show that the three welding procedures produce welded joints free of defects and with adequate shape. Although small differences on mechanical properties and microstructure have been observed, the three welding programs attained compatible results with international standards used in the aerospace segment. The welding program #B, due the reduced heat input used, was considered to obtain slightly advantage over the others.