Anthrone and oxanthrone C,O-diglycosides from Picramnia teapensis

Two C,O-diglycosylated compounds, the anthrone picramnioside F, and the oxanthrone mayoside C, were isolated from the stem bark of Picramnia teapensis, along with the previously reported anthraquinones, 1-O-beta -D- and 8-O-beta -D-glucopyranosyl emodin. The compounds were separated by recycling-HPLC, and their structures were determined on the basis of spectroscopic analysis. CD measurements were used to establish the absolute configuration of the anthrone and oxanthrone. The antifungal activity of 1-O-beta -D- and 8-O--D-glucopyranosyl emodin against Leucoagaricus gongilophorus was shown to be similar to that of the lignan sesamin. (C) 2000 Elsevier B.V. Ltd. All rights reserved.

Recycling of glass cullet as aggregate for clays used to produce roof tiles

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Continuous ethanol production in a nonconventional five-stage system operating with yeast cell recycling at elevated temperatures

Three ranges of increasing temperatures (35-43, 37-45, 39-47degreesC) were sequentially applied to a five-stage system continuously operated with cell recycling so that differences of 2degreesC (between one reactor to the next) and 8degreesC (between the first reactor at the highest temperature and the fifth at the lowest temperature) were kept among the reactors for each temperature range. The entire system was fed through the first reactor. The lowest values of biomass and viability were obtained for reactor R-3 located in the middle of the system. The highest yield of biomass was obtained in the effluent when the system was operated at 35-43degreesC. This nonconventional system was set up to simulate the local fluctuations in temperature and nutrient concentrations that occur in different regions of the medium in an industrial bioreactor for fuel ethanol production mainly in tropical climates. Minimized cell death and continuous sugar utilization were observed at temperatures normally considered too high for Saccharomyces cerevisiae fermentations.

PET containers in Brazil: Opportunities and challenges of a logistics model for post-consumer waste recycling

The use of post-consumer materials is directly related to reducing the cost of production and extraction of natural resources. Non-recyclable materials are randomly disposed in the environment. Brazil is one of the largest consumers of PET (polyethylene terephthalate) bottles. The purpose of this paper is to describe the opportunities and challenges of the logistics model for post-consumer PET bottle recycling in Brazil, while providing knowledge of its practices along the recycling chain. The results describe the need to educate those directly and indirectly involved in the process: to reduce consumption in order to reduce the amount of waste generated: to structure the post-consumer reverse chain and engage industrial sectors and government, through public policies, to support cleaner technologies along the PET bottle production chain. (C) 2010 Elsevier B.V. All rights reserved.

Genetic and physiological alterations occurring in a yeast population continuously propagated at increasing temperatures with cell recycling

This work investigated the effects of increasing temperature from 30 degrees C to 47 degrees C on the physiological and genetic characteristics of Saccharomyces cerevisiae strain 63M after continuous fermentation with cell recycling in a system of five reactors in series. Steady state was attained at 30 degrees C, and then the temperature of the system was raised so it ranged from 35 degrees C in the last reactor to 43 degrees C in the first reactor or feeding reactor with a 2 degrees C difference between reactors. After 15 days at steady state, the temperature was raised from 37 degrees C to 45 degrees C for 25 days at steady state, then from 39 degrees C to 47 degrees C for 20 days at steady state. Starter strain 63M was a hybrid strain constructed to have a MAT a/alpha, LYS/lys, URA/ura genotype. This hybrid yeast showed vigorous growth on plates at 40 degrees C, weak growth at 41 degrees C, positive assimilation of melibiose, positive fermentation of galactose, raffinose and sucrose. of 156 isolates obtained from this system at the end of the fermentation process, only 17.3% showed the same characteristics as starter strain 63M. Alterations in mating type reaction and in utilization of raffinose, melibiose, and sucrose were identified. Only 1.9% of the isolates lost the ability to grow at 40 degrees C. Isolates showing requirements for lysine and uracil were also obtained. In addition, cell survival was observed at 39-47 degrees C, but no isolates showing growth above 41 degrees C were obtained.

Foundry sand recycling in the troughs of blast furnaces: a technical note

The foundry sand agglomerated with alkaline phenolic resin, used for the manufacture of molds, was found to be a residue which is able to be recycled, minimizing the costs of disposal and the environmental impact. This paper analyzes the thermomechanical regeneration and leaching processes and also assesses the influence of additives on the improvement of the mechanical properties of the sands. Besides, the industrial experiments carried out at CSN aiming at the foundry sand recycling in the covering of the blast furnace troughs are presented. (C) 2003 Elsevier B.V. All rights reserved.

Optimization of neutral hydrolysis reaction of post-consumer PET for chemical recycling

The neutral hydrolysis reaction of post-consumer poly(ethylene terephthalate) in solid state was studied through the reaction of the polymer with water at the molar ratio 1:91 with autogenous pressure. Two sizes of post-consumer PET flakes and temperatures of 135 °C, 170°C and 205°C with pressures of 4.0 atm, 7.5 atm and 13.5 atm, respectively, were considered. With reaction time equal to 6h, the method reached 99% depolymerization at 205°C, 8.2% at 170 °C and 1.7% at 135°C. The reaction extension was measured by separating the terephthalic acid formed in the process and calculating by gravimetry how much material could still be reacted. Through the viscosimetry of diluted, solutions and the counting of carboxylic end groups in the remaining material from the gravimetric assay, it was possible to suggest that the reaction occurs randomly and in the whole volume of the polymeric particle and not solely on the surface. The terephthalic acid obtained and then purified was characterized by elemental analysis, magnetic nuclear resonance, size and panicle size distribution and spectrophotometry in the visible spectrum, and it was similar to the petrochemical equivalent, with purity recorded in carbon base equal to 99.9%.

Zinc and lead content and availability in Brazilian soil contaminated with residue of a secondary smelting lead recycling plant

The sequential extraction procedure of Zinc and lead performed in a Brazilian soil showed that it presents high pollution potential once over 90% of total lead is present in fractions where the metals can be easily mobilized. The fraction contents are as follow: F1 = 174 and 15 mg kg-1; F2 = 3155 and 9.7 mg kg -1; F3 = 99 and 1.6 mg kg -1; Residual fraction = 38 and 5.5 mg kg -1 for lead and zinc, respectively. The comparison with non contaminated soil only Pb 2+ concentration is above its intervention reference concentration, 900 mg kg -1.

An emergy-based evaluation of a reverse logistics network for steel recycling

Efficient implementation of recycling networks requires appropriate logistical structures for managing the reverse flow of materials from users to producers. The steel sheet distributor studied had established a protocol for scrap recovery with the steel plant and its customers. The company invested in producing containers, hiring a specialized labor force and in purchasing trucks for container transportation to implement the logistics network for recycling. That network interconnected the company with two kinds of customers: the ones returning scrap and the ones who preferred to continue business-as-usual. The logistical network was analyzed using emergy synthesis, and the data obtained were used to evaluate and compare the system's environmental costs and benefits from the perspective of the distributor and the steel plant operator. The use of emergy ternary diagrams provided a way to assess recycle strategies to compare the relative economic and environmental benefits of the logistical network implemented. The minimum quantity of scrap that the distributor must recover to improve environmental benefits was determined allowing decision on whether it is worth keeping the system running. The new assessment method proposed also may help policy-makers to create strategies to reward or incentive users of reverse logistics, and help to establish regulations, by decreasing taxes or stimulating innovation, for effectively implement the National Policy on Solid Waste. (C) 2013 Elsevier Ltd. All rights reserved.

Natural rubber/leather waste composite foam: A new eco-friendly material and recycling approach

This article describes a new approach of recycling the leather waste (shavings) using it as filler in natural rubber foams composites. The foams were prepared using different amounts of leather waste (0-60 parts per hundred of rubber) and submitted to morphological (SEM microscopy) and mechanical analyses (cyclic stress-strain compression). The increase of leather shavings on the composite causes an increase of viscosity in the mixture, which reflects in the foaming process. This results in smaller and fairly uniform cells. Furthermore, expanded rubber has the biggest cell size, with more than 70% of cell with 1000 mu m, while the composite with the higher concentration of leather has around 80% of total number of cells with 100-400 mu m. The mechanical parameters were found to depend on the leather dust concentration. Moreover, the stiffness rises with the increase of leather shavings; consequently, the compression force for expanded rubber was 0.126 MPa as well as the composite with higher concentration of leather was 7.55 MPa. (c) 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015, 132, 41636.

Recycling scrap automotive heat shield insulation material

Automotive heat shields are usually composed of two metal sheets enclosing an insulating material with a paper-like texture that contains refractory ceramic particles. This article discusses the results achieved by recycling the scrap automotive insulation that is discarded in landfills, using the same concept as paper recycling. For comparison with the original product, tests of thickness, bulk density, weight loss on ignition, tensile strength, compressibility, and recovery were performed on recycled materials produced in a so-called "manual" process (involving little automation and performed in adapted facilities) without pressing, and pressed once, twice, and four times. Materials recycled in a so-called "industrial" process (in a paper recycling plant) without pressing, and pressed once were also tested. The recycled materials can be considered approved with respect to the main requirement, thermal insulation, since they dissipated the under-hood temperature by more than 300 A degrees C (like the original product). Like the heat insulation tests, the thermogravimetric analysis suggested that the recycled materials showed higher stability than the original product. Thermogravimetric, microscopy, and energy dispersive spectroscopy analyses indicated that the structural and compositional characteristics of the original product were preserved after recycling.