The position effect of structural Eucalyptus round timber on the flexural modulus of elasticity

A madeira roliça possui grande emprego nas construções civis, desempenhando a função de vigas, colunas, fundações, postes para distribuição de energia elétrica, entre outras, apresentando a vantagem de não ser processada, como é o caso da madeira serrada. O projeto envolvendo elementos roliços requer, além de outras variáveis estruturais, o conhecimento do módulo de elasticidade. No Brasil, os documentos normativos que tratam da determinação das propriedades de rigidez e resistência para peças roliças de madeira estão em vigência há mais de vinte anos sem revisão técnica. A madeira roliça, por geralmente possuir eixo com curvatura não nula, pode apresentar, segundo a posição da peça no ensaio de flexão, valores diferentes do módulo de elasticidade. Este trabalho tem como objetivo analisara influência da posição de peças roliças de madeira de Eucalyptus grandis na determinação do módulo de elasticidade na flexão. O ensaio de flexão utilizado é o de três pontos, sendo cada peça avaliada em duas posições distintas, definidas mediante o giro da seção transversal em torno do eixo. Os resultados encontrados indicam a necessidade do ensaio de flexão em, pelo menos, duas posições distintas da peça.

Weathering degradation of polyester and polypropylene geotextiles

This paper presents results of physical and mechanical tests in polyester (PET) and polypropilene (PP) nonwoven geotextiles that were exposed to weathering conditions (solar radiation, humidity, wind, rain) after some specific periods of exposure (1, 2, 3 and 4 months). ASTM D5970 and Brazilian standards (NBR) recommendation were followed in this research. Results show variations in tensile properties and in the mass per unit area. Variations in the deformations were more significant in the PP geotextile when compared to the PET geotextile.

Hydrodynamic characterization and performance evaluation of an aerobic three phase airlift fluidized bed reactor in a recirculation aquaculture system for Nile Tilapia production

The hydrodynamic characterization and the performance evaluation of an aerobic three phase fluidized bed reactor in wastewater fish culture treatment are presented in this report. The objective of this study was to evaluate the organic matter, nitrogen and phosphorous removal efficiency in a physical and biological wastewater treatment system of an intensive Nile Tilapia laboratory production with recirculation. The treatment system comprised of a conventional sedimentation basin operated at a hydraulic detention time HDT of 2.94 h and an aerobic three phase airlift fluidized bed reactor AAFBR operated at an 11.9 min HDT. Granular activated carbon was used as support media with density of 1.64 g/cm(3) and effective size of 0.34 mm in an 80 g/L constant concentration. Mean removal efficiencies of BOD, COD, phosphorous, total ammonia nitrogen and total nitrogen were 47%, 77%, 38%, 27% and 24%, respectively. The evaluated system proved an effective alternative for water reuse in the recirculation system capable of maintaining water quality characteristics within the recommended values for fish farming and met the Brazilian standards for final effluent discharges with exception of phosphorous values. (C) 2011 Elsevier B.V. All rights reserved.

Queijo Parmesão: caracterização físico-química, microbiológica e microestrutura

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Determinação de pesticidas organoclorados em água de manancial, água potável e solo na região de Bauru (SP)

This paper evaluates the presence of organochlorinated pesticides in the water supply system of the city of Bauru, State of São Paulo, Brazil. Soil samples were collected in agricultural areas and water samples at several points of the water source (river) and the distribution net. The results of the analyses of the water from the source were compared with the Brazilian classification system for inland waters (CONAMA/86) and the results of analyses of treated water were compared with Brazilian standards for finished drinking water.

Determination and statistical treatment of short-circuit currents for faults on the lines of networks of 440 kV CESP system

The distribution of short-circuit current is investigated by means of two methods, one direct and the other analytic; both methods consider uniform probability distribution of line faults. In the direct method, the procedure consists of calculating fault currents at equidistant points along the line, starting from one of the end points and considering the other end open. The magnitude of the current is classified according to Brazilian standards (regulation NBR-7118). The analytic method assumes that the distribution of short-circuit currents through the busbar and the distribution of the line length connected to it are known, as well as the independence of values. The method is designed to determine the probability that fault currents through a line will surpass the pre-established magnitude, thus generating frequency distribution curves of short-circuit currents along the lines.

Estudo comparativo de coletores solares sem cobertura utilizados para aquecimento de piscinas

Pós-graduação em Engenharia Mecânica - FEB

Estudo comparativo do estado de conservação de acrne moída através de métodos microbiológicos e físico-químicos

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Remoção de nitrogênio de água residuária de produção intensiva de tilápias com recirculação utilizando reator de leito fluidizado com circulação em tubos concêntricos

Pós-graduação em Engenharia Civil - FEIS

Ingredientes de origem animal e aminoácidos digestíveis em rações para poedeiras comerciais

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Properties of Mortar Using Cubes, Prism Halves, and Cylinder Specimens

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Análise do processo de execução de edificações compostas por paredes de concreto executadas in loco

This work presents a fast, easy, standardized and planned method to build family homes in order to collaborate with the decline of housing deficit and, at the same time, meet families who wish to invest in building their own houses, once that our country is experiencing an economical prosperity . This method has been widely used nowadays because it is being deployed in large-scale and in a standardized pattern, reducing decreasing significantly the construction time. The concrete wall, shaped in loco depends on unique processes. For this reason, a well trained staff is required so the constructive process can be executed in a fast pace, showing better results than other construction methods. This project will address all the materials used to build the molded concrete walls in loco, their sequence assembly, application, types, characteristics and performances. At the end, a way used by building companies of locating the concrete will also be given. Although there is no specific Brazilian norm for this type of construction, a study on this topic will soon be released. Therefore, the studies for the execution of this project were based on Brazilian standards prevailing at the time, construction magazines and books that are based on building methods considered more common

Análise do desempenho físico-mecânico de painéis compensados de Pinus sp. produzidos com adesivos aquosos a base de poliacetato de vinila e de homopolímero vinílico

This study aimed to evaluate the physico-mechanical performance of three PVA adhesive formulations according to the Brazilian standards for plywood testing and to evaluate the results with those presented in the technical literature and specified in normative documents. The study presents the production process of the panels, the obtaining of samples and, finally, the implementation of physico-mechanical characterization tests based on plywood Brazilian standards. For the panels production it was used a gramature of 120 g / m² and applied a pressure of 15 bars and two temperature combinations and pressing time for each adhesive. The commercial adhesives used were PVA 1810, PVA 1060 and Vinyltec 239. The physical tests conducted were thickness swelling, density, moisture content and water absorption. The mechanical tests were static flexion, for the determination of elasticity modulus (MOE) and rupture modulus (MOR), and shear in the glue line. Among the three formulations studied none showed good performance in the presence of water. However, other trials in the adhesive showed better results and closer to the commercially equivalent used, in the case the urea-formaldehyde, was the PVA 1810, that can be applied in non-structural uses and in environments without the presence of moisture

Ergonomia e design de vestimentas ocupacionais no Brasil: foco em equipamentos de proteção individual no setor de petróleo e gás

Pós-graduação em Design - FAAC