Crystallization mechanism and properties of a blast furnace slag glass

The complex crystallization process of a Brazilian blast-furnace slag glass was investigated using differential scanning calorimetry (DSC), X-ray diffraction, optical microscopy, transmission electron microscopy (TEM), selected area diffraction (SAD), energy dispersive spectroscopy (EDS) and micro-Raman spectroscopy. Three crystalline phases (merwinite, melilite and larnite) were identified after heat treatment between Tg (742°C) and the DSC crystallization peak (T = 1000°C). Merwinite was identified as a metastable phase. A small amount (0.004 wt%) of metallic platinum was found in the glass composition. Particles of Pt3Fe, detected by EDS and SAD-TEM, were the starting points of crystallization acting, therefore, as heterogeneous nucleating sites. Only melilite and larnite precipitated in a glass sample heat-treated at 1000°C for 1 h. The flexural strength of this crystallized sample was less than that of the glass, probably due the allotropic phase transformation of larnite. © 2000 Published by Elsevier Science B.V. All rights reserved.

Implementation of convective heating in Companhia Siderúrgica Nacional Blast Furnace runners

This paper describes the main characteristics and advantages of convective heating system for refractory lining, compared with conventional heating systems. In addition the main results obtained are presented with its implementation in CSN Blast Furnace #2 and 3 Runners, in terms of cost and equipment availability, as well as the need for ceramic coating to protect the lining against oxidation, arising from excessive air combustion. © 2012 Elsevier Ltd. All rights reserved.

A methodology to investigate the wear of blast furnace hearth carbon refractory lining

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Utilização do coque verde de petróleo da Petrobras em substituição parcial ao carvão mineral das misturas injetadas em altos fornos

The Petrobras produced green petroleum coke (GPC) is a carbon rich fuel, virtually ash-free, with low sulfur content, and is a fuel suitable to replace metallurgical coke in blast furnaces. The GPC was tested in a pulverized coal injection simulator built in the Volta Redonda research center. It presented a low burning efficiency due to low volatile material content and high substitution rate by the carbon content. The tests were carried out in blast furnaces with ≤ 50% Petrobras GPC in the coal blends. The injected coal/CVP mixtures produced no negative side effects in the blast furnace grinding systems, pneumatic conveying, or operating process. The mixture burning process inside the blast furnace showed a decrease in fuel consumption, with a significant reduction in metallurgical coke consumption. The industrial-scale tests of the GPC mixtures did not reach the 70% maximum for lack of the GPC feedstock, which is necessary to continue with standard coal mixtures.

Estudo da combustão de carvões e misturas com o coque verde de petróleo injetadas em altos fornos

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Foundry sand recycling in the troughs of blast furnaces: a technical note

The foundry sand agglomerated with alkaline phenolic resin, used for the manufacture of molds, was found to be a residue which is able to be recycled, minimizing the costs of disposal and the environmental impact. This paper analyzes the thermomechanical regeneration and leaching processes and also assesses the influence of additives on the improvement of the mechanical properties of the sands. Besides, the industrial experiments carried out at CSN aiming at the foundry sand recycling in the covering of the blast furnace troughs are presented. (C) 2003 Elsevier B.V. All rights reserved.

Estudo de gaseificação de lama de alto forno arcelormital tubarão

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Estudo da utilização de biomassa em substituição parcial ao carvão mineral utilizado no processo de fabricação do ferro gusa em alto-forno

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Atributos químicos do solo, crescimento radicular e produtividade do arroz de acordo com a aplicação de escórias

Resíduos industriais são fontes alternativas de nutrientes para as plantas e sua utilização decorre da necessidade de diminuir o acúmulo dos resíduos nos centros de produção. O objetivo deste trabalho foi avaliar o efeito de escórias de siderurgia nos atributos químicos do solo, no desenvolvimento e na produtividade de grãos do arroz de terras altas irrigado por aspersão. O delineamento experimental foi em blocos casualizados, com três tratamentos constituídos de duas escórias, alto-forno (196 g kg-1 de Si) e aciaria (56 g kg-1 de Si), e a testemunha sem aplicação, com oito repetições. As escórias podem ser usadas como corretivo de acidez do solo e como fonte de silício. As alterações nos atributos químicos do solo estão relacionadas com a composição química das escórias. A escória de alto-forno proporcionou maior crescimento radicular em profundidade e melhor distribuição no perfil do solo e, conseqüentemente, maior produção de massa de matéria seca da parte aérea e produtividade de grãos de arroz.

Efeito de escória de alto forno no crescimento radicular e na produtividade de arroz

A utilização agrícola de resíduos industriais como fertilizantes decorre da necessidade de diminuir o efeito nocivo do acúmulo de nutrientes nos centros de produção. O objetivo deste trabalho foi avaliar os efeitos de escória de alto forno no crescimento radicular e na produtividade do arroz de terras altas irrigado por aspersão. O experimento foi realizado no campo, adotando-se o delineamento experimental de blocos casualizados, com cinco doses de escória de alto forno (0, 2.550, 5.100, 10.200 e 15.300 kg ha-1) com quatro repetições. A utilização de escória melhorou a condição química do solo, aumentou o crescimento e a superfície radicular, diminuiu o diâmetro das raízes e elevou os teores de silício no solo e na planta, resultando em aumento da produtividade.

Behaviour of biofuel addition on metallurgical properties of sinter

Blast furnace gas yield is essentially controlled by a gas-solid reaction phenomenon, which strongly influences hot metal manufacturing costs. As a result of rising prices for reducing agents on the international market, Companhia Siderurgica Nacional decided to inject natural gas into its blast furnaces. With more gas inside the furnace, the burden permeability became even more critical. To improve blast furnace gas yield, a new technological approach was adopted; raising the metallic burden reaction surface. To that end, a special sinter was developed with permeability being controlled by adding micropore nucleus forming agents, cellulignin coal, without, however, degrading its mechanical properties. This paper shows the main process parameters and the results from physicochemical characterisation of a sinter with controlled permeability, on a pilot scale, compared to those of conventional sinter. Gas flow laboratory simulations have conclusively corroborated the positive effects of micropore nucleus forming agents on enhancing sinter permeability.

Innovaciones en la gestión y calidad de los revestimientos refractarios en la Compañía Sideŕurgica Nacional (Brasil)

The work describes actions carried out in colaboration among the National Steel Company - (CSN)-Brazil and the Interdisciplinary Laboratory of Electrochemistry and Ceramic - LIEC of the Federal University of Sao Carlos Brazil (UFSCar-Brazil), in the area of I&D, for integral management and improvement of the quality and performance of the refractory linings in the sintering areas, blast furnace, hot air pipe lines transferency to the blast furnace, pig-iron ladles, running channels, blast furnaces hearths, torpedo car, etc., as well as, the economic impact generated by the installation of the adopted measures.

Corrosion behavior in graphite refractories impregnated with ZrO 2 and CeO 2 carrying solutions

This paper investigates corrosion behavior in graphite refractory hot metal impregnated with ZrO 2 and CeO 2 carrying solutions used in Blast Furnace hearth, consisting of 50% graphite and 50% anthracite. Corrosions tests were carried out by means of finger test method in an induction furnace, using bar-shaped 30×30×280 mm test specimens and hot metal from CSN#2 Blast Furnace runner. The temperature chosen for this test was 1520°C and sixty-minute isotherm. Upon test completion, test specimens were characterized by their dimensional variation, X-ray diffractometry and Scanning Electronic Microscopy (SEM).

Use of slag/sugar cane bagasse ash (SCBA) blends in the production of alkali-activated materials

Blast furnace slag (BFS)/sugar cane bagasse ash (SCBA) blends were assessed for the production of alkali-activated pastes and mortars. SCBA was collected from a lagoon in which wastes from a sugar cane industry were poured. After previous dry and grinding processes, SCBA was chemically characterized: it had a large percentage of organic matter (ca. 25%). Solutions of sodium hydroxide and sodium silicate were used as activating reagents. Different BFS/SCBA mixtures were studied, replacing part of the BFS by SCBA from 0 to 40% by weight. The mechanical strength of mortar was measured, obtaining values about 60 MPa of compressive strength for BFS/SCBA systems after 270 days of curing at 20 °C. Also, microstructural properties were assessed by means of SEM, TGA, XRD, pH, electrical conductivity, FTIR spectroscopy and MIP. Results showed a good stability of matrices developed by means of alkali-activation. It was demonstrated that sugar cane bagasse ash is an interesting source for preparing alkali-activated binders. © 2013 by the authors; licensee MDPI, Basel, Switzerland.

Eficiência de escórias de siderurgia na cultura do feijoeiro em sistema de semeadura direta

In the no till system, soil acidity correction practice is restricted to limestone use and there is little information regarding slag. The study aimed to evaluate the amendments in soil chemical properties, yield and bean nutrient uptake according to the application forms of slags, compared to limestone, in the implantation of no till system. The experiment was conducted in the field at College of Agricultural Sciences, Botucatu (SP) from December 2010 to May2011. The treatments consisted of two application ways of seven soil acidity correctives: steel slag, blast furnace slag, ladle furnace slag, stainless steel slag (agrosilício), wollastonite, lime and calcined dolomite lime, plus one control without corrective application. Each material dose was calculated to raise the base saturation to 70%. Soil acidity was neutralized down to 20cm with limestones, whereas for wollastonite and ladle furnace slag those effects occurred down to 10cm, for steel slag, blast furnace slag and agrosilício the corrective effect was restricted to the first 5cm. The bean yield increased by application of correctives in soil acidity, without differences between the application ways.