MICROSTRUCTURAL CHARACTERIZATION OF DUAL AND MULTIPHASE STEELS APPLIED TO AUTOMOTIVE INDUSTRY

TRIP (Transformation Induced Plasticity) and DP (Dual-Phase) steels are written in a new series of steels which present excellent mechanical properties. As for microstructure aspect, TRIP steels consist on a ferrite matrix with a second phase dispersion of other constituents, such as bainite, martensite and retained austenite, while dual-phase steels consist on martensite dispersion in a ferrite matrix. In order to identify the different microconstituents present in these materials, microstructure characterization techniques by optical microscopy (using different etchants: LePera, Heat-Tinting and Nital) and scanning electron microscopy were carried out. This being so, microstructures were correlated with mechanical properties of materials, determined by means of tensile tests. It is concluded that steels assisted by TRIP effect have a strength and elongation relation higher than the dual-phase one. With microstructure characterization, it was observed phases present in these materials microstructure.

Estudo do efeito springback em aços avançados de alta resistência aplicados a indústria automobilística

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Efeitos das microestruturas bainíticas e multifásicas nas propriedades mecânicas de um aço AISI 4340

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Efeito da microestrutura nas propriedades mecânicas de aços automotivos dissimilares soldados à laser

Pós-graduação em Engenharia Mecânica - FEG

Performance of advanced generation from a hybrid Japanese cucumber

A endogamia reduz o vigor em plantas pela diminuição da proporção de loci heterozigotos. Entretanto, a influência da endogamia é diferente entre as espécies. O objetivo deste trabalho foi avaliar a depressão causada por endogamia em uma população de pepino do tipo japonês. A partir do intercruzamento entre plantas do híbrido Natsu suzumi foi obtida a geração F2, considerada como população S0. Obtiveram-se progênies S1, S2, S3, S4 e S5, através de autofecundações sucessivas pelo método do SSD ('Single Seed Descent'). Foram sete tratamentos (híbrido Natsu suzumi, populações S0 a S5) e o delineamento experimental foi em blocos ao acaso, com seis repetições e cinco plantas por parcela cultivadas em ambiente protegido de 21/08/2002 à 29/11/2002. Foram avaliados o número de folhas, semanalmente, o número e a massa de frutos, total e comercial, número de nós e porcentagem de nós com brotações laterais. Na comparação entre as populações S0 a S5 não foram observadas diferenças para todas as características avaliadas demonstrando não haver perda de vigor por endogamia nesta população.

Studies on the cooling minimum quantity and conventional cooling at hardened steels in grinding process

The purpose of this work is to explain the concept of cutting fluids reasonable usage through the fluid minimum quantity in grinding processes. on that purpose, the development of a new nozzle and an own and adequate methodology should be required in order to obtain good results and compare them to the conventional methods. The analysis of the grinding wheel/cutting fluid performance was accomplished from the following input parameters: flow rate variation by nozzle diameter changes (three diameters values: 3mm, 4mm and 5mm), besides the conventional round nozzle already within the machine. Integral oil and a synthetic emulsion were used as cutting fluids and a conventional grinding wheel was employed. The workpieces were made of steel VC 131, tempered and quenched with 60HRc. Thus, as the flow rate and the nozzle diameter changes, keeping steady fluid jet velocity (equal to cutting velocity), attempted to find the best machining conditions, with the purpose to obtain a decrease on the cutting fluid volume, taking into consideration the analysis of the process output variables such as cutting strength, cutting specific energy, grinding wheel wear and surface roughness. It was verified that the 3mm diameter optimized nozzle and the integral oil, in general, was the best combination among all proposed.

GREEN MACHINING ORIENTED TO DIMINISH DENSITY GRADIENT FOR MINIMIZATION of DISTORTION IN ADVANCED CERAMICS

After sintering advanced ceramics, there are invariably distortions, caused in large part by the heterogeneous distribution of density gradients along the compacted piece. To correct distortions, machining is generally used to manufacture pieces within dimensional and geometric tolerances. Hence, narrow material removal limit conditions are applied, which minimize the generation of damage. Another alternative is machining the compacted piece before sintering, called the green ceramic stage, which allows machining without damage to mechanical strength. Since the greatest concentration of density gradients is located in the outer-most layers of the compacted piece, this study investigated the removal of different allowance values by means of green machining. The output variables are distortion after sintering, tool wear, cutting force, and the surface roughness of the green ceramics and the sintered ones. The following results have been noted: less distortion is verified in the sintered piece after 1mm allowance removal; and the higher the tool wear the worse the surface roughness of both green and sintered pieces.

Influence of the grinding wheel's dive speed on the damage of rectified hardened steels

The world tendency is the increase of the productivity and the production of pieces more and more sophisticated, with high degree of geometric and dimensional tolerances, with good surface finish and low cost. Rectification is responsible for the final finish in the machining process of a material. However, damages generated in this production phase affect all the resources used in the previous processes. Great part of the problems happennig in the rectification process is due to the enormous temperature generated in this activity because of the machining conditions. The dive speed, which is directly related to the productivity, is considered responsible for the damages that occur during rectification, limiting its values to those that do not cause such damages. In this work, through the variation of the dive speed in the process of cylindrical grinding of type ABNT D6 steel, rationalizing the application of two cutting fluids and using a CBN (cubic boron nitrate) abrasive wheel with vitrified blond, the influence of the dive speed on the surface damages of hardened steels was evaluated. The results allowed to say that the dive speed, associated to an efficient cooling and lubrication, didn't provoke thermal damages (including heated zones, cracks and tension stresses) to the material. Residual stresses and the roughness of rectified materials presented a correlation with the machining conditions. The work concluded that it is possible to increase the productivity without provoking damages in the rectified components.

Orientation dependence of stored energy of cold work in semi-processed electrical steels after temper rolling

Microhardness measurements were carried out in a low carbon lamination steel after 6% of temper rolling, in order to evaluate local variations of work hardening as a function of crystallographic orientation. EBSD (electron back scattered diffraction) was used to determine grain orientations with respect to individual rolling planes and rolling directions. Hardness was shown to increase with the local Taylor factor. TEM observations and a well-known dislocation hardening model were used to confirm the equivalence between hardness values and the stored energy of cold work. A definite correlation between stored energy and Taylor factors could therefore be established, being more consistent than previous data reported in the literature. The improvement was thought to be related to the rather small plastic deformation, during which Taylor factors could be considered to remain constant. (c) 2006 Elsevier B.V. All rights reserved.

Surface Integrity Analysis when Milling Ultrafine-grained Steels

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Preoperative and Postoperative Nutritional Evaluation in Patients with Non-advanced Megaesophagus

Megaesophagus, an affection characterized by aperistalses of the esophageal body and deficient relaxation of lower esophageal sphincter, has disphagia as main symptom. The aim of this study was to evaluate the nutritional status of patients with non advanced megaesophagus in pre and post-operative periods of cardiomyotomy. Ten patients were evaluated at 5 moments (pre-operative - M 1 and post-operative - 1, 3, 6 ant 12 months after surgery). The anthropometric, hematimetric and biochemical parameters were studied in the 5 moments. Conclusions: 1. Most 017 the patients with non-advanced megaesophagus are eutrophic; 2. Surgical treatment determines an improvement in nutritional status and an increase in HDL cholesterol values.

Tc-99m-sestamibi scintigraphy used to evaluate tumor response to neoadjuvant chemotherapy in locally advanced breast cancer: A quantitative analysis

To evaluate the tumor response to neoadjuvant chemotherapy, Tc-99m-sestamibi breast scintigraphy was proposed as a quantitative method Fifty-five patients with ductal carcinoma were studied They underwent breast scintigraphy before and after neoadjuvant chemotherapy, along with clinical assessment and surgical specimen analysis The regions of interest on the lesion and contralateral breast were identified, and the pixel counts were used to evaluate lesion uptake in relation to background radiation The ratio of these counts before to after neoadjuvant chemotherapy was assessed The decrease in uptake rate due to chemotherapy characterized the scintigraphy tumor response The Kruskal-Wallis test was used to compare the mean scintigraphic tumor response and histological type Dunn's multiple comparison test was used to detect differences between histological types The Mann-Whitney test was used to compare means between quantitative and qualitative variables scintigraphic tumor response vs clinical response and uptake before chemotherapy vs scintigraphic tumor response The Spearman's test was used to correlate the quantitative variables of clinical reduction in tumor size and scintigraphic tumor response All of the variables compared presented significant differences The change in Tc-99m-sestamibi uptake noted on breast scintigraphy, before to after neoadjuvant chemotherapy, may be used as an effective method for evaluating the response to neoadjuvant chemotherapy, since this quantification reflects the biological behavior of the tumor towards the chemotherapy regimen Furthermore, additional analysis on the uptake rate before chemotherapy may accurately predict treatment response

Predictors of first-year survival in patients with advanced COPD treated using long-term oxygen therapy

Little evidence-based guidance is available to aid clinicians in determining short-term prognoses in very severe COPD patients. Therefore, the present study was designed to provide a prospective assessment (1) of the mortality rates and (2) whether the baseline measurements may be determinants of 1-year mortality in hypoxemic COPD patients receiving long-term oxygen therapy (LTOT).Seventy-eight clinically stable patients with advanced COPD treated using LTOT were enrolled in a prospective cohort study. Outcome variable: first-year mortality. Baseline measurements: categorical variables: age (<60 or >= 60 years); gender; body mass index (<20 or >= 20 kg/m(2)); fat-free mass (FFM) index (<16 [men] and <15kg/m(2) [women]; baseline dyspnea index (BDI) (<= 3 or >3); and corticosteroid use. Continuous variables: smoking history; lung function; FFM; fat mass; hemoglobin; hematocrit; arterial blood gases; forearm muscle strength; St. George's Respiratory Questionnaire (SGRQ); and comorbidity score. By the end of 1-year of follow-up, 12 patients (15.4%) had died. Kaplan-Meier curves showed that BDI <= 3 was the only variable associated with higher mortality. Cox proportional hazards analysis revealed that tower PaO2 and SPO2, higher PaCO2 and SGRQ scores were associated with reduced survival. In the multivariate analysis, BDI remained predictive of mortality (hazard ratio [HR], 0.50; 95% confidence interval [CI], 0.31-0.81), as did PaO2 (HR, 0.49; 95% CI, 0.26-0.95). These data suggest that readily available parameters as dyspnea intensity and hypoxemia severity may be useful in predicting first-year survival rates in advanced COPD patients receiving LTOT (C) 2007 Elsevier Ltd. All rights reserved.

Zona thinning with a noncontact diode laser in ICSI embryos from women of advanced age

Purpose: the objective of this study was to determine if the zona thinning (ZT) technique improved the rates of implantation and clinical pregnancy for patients aged, greater than or equal to38 years submitted to an ICSI program.Methods: A total of 100 patients submitted to ICSI and aged, greater than or equal to38 years were divided in a prospective and randomized manner into two groups: Group I - patients submitted to ZT (n = 50); a laser diode with 1.48 mum wavelength (Fertilaser) was used for the ZT procedure with 1-2 irradiations of 10 ms applied to four different positions on the zona pellucida (ZP) of each embryo to thin 60-90% of the ZP (each point with a 15-20 mum length of ZT). Group II - patients with no ZT (n = 50). In both groups, embryo transfer was performed on the second or third day.Results: the age of Group I patients (39.8 +/- 1.3) did not differ (p = 0.67) from that of Group II patients (40 +/- 1.9). The number of oocytes retrieved at metaphase II from Group I (6.4 +/- 4.2) and Group II (6.8 +/- 5) was similar (p = 0.94). Normal fertilization rates and cleavage rates were similar (p = 0.78 and p = 0.63, respectively) for Group I (71.5 +/- 22% and 96.7 +/- 11%) and Group II (73.5 +/- 19.7% and 96 +/- 11%, respectively). The number of embryos transferred was similar (p = 0.53) for the two groups (Group I = 3.1 +/- 1.3; Group II = 2.9 +/- 1.1). The thickness of the ZP of Group I embryos (16.9 +/- 2.4 mum) did not differ (p = 0.97) from that of Group II embryos (16.9 +/- 2.3 mum). The rates of embryo implantation and clinical pregnancy per embryo transfer were similar (p = 0.67, p = 0.61) for Group I (7 and 16%, respectively) and for Group II (8.2 and 22%, respectively).Conclusions: These results suggest that ZT in the population aged, 38 years may have no impact on ICSI success rates. However, this conclusion is limited to a situation in which length of the laser ZT was less than or equal to 20 mum and the laser was applied to four different positions.