Surface modification of polymeric materials by cold atmospheric plasma jet

In this work we report the surface modification of different engineering polymers, such as, polyethylene terephthalate (PET), polyethylene (PE) and polypropylene (PP) by an atmospheric pressure plasma jet (APPJ). It was operated with Ar gas using 10 kV, 37 kHz, sine wave as an excitation source. The aim of this study is to determine the optimal treatment conditions and also to compare the polymer surface modification induced by plasma jet with the one obtained by another atmospheric pressure plasma source the dielectric barrier discharge (DBD). The samples were exposed to the plasma jet effluent using a scanning procedure, which allowed achieving a uniform surface modification. The wettability assessments of all polymers reveal that the treatment leads to reduction of more than 40 degrees in the water contact angle (WCA). Changes in surface composition and chemical bonding were analyzed by x-ray photoelectron spectroscopy (XPS) and Fourier-Transformed Infrared spectroscopy (FTIR) that both detected incorporation of oxygen-related functional groups. Surface morphology of polymer samples was investigated by Atomic Force Microscopy (AFM) and an increase of polymer roughness after the APPJ treatment was found. The plasma-treated polymers exhibited hydrophobic recovery expressed in reduction of the O-content of the surface upon rinsing with water. This process was caused by the dissolution of low molecular weight oxidized materials (LMWOMs) formed on the surface as a result of the plasma exposure. (C) 2014 Elsevier B.V. All rights reserved.

New flexible and transparent solution-based germanium-sulfide polymeric materials

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Estudo de polímeros comerciais tratados a plasma em pressão atmosférica

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Characterization of Post-Consumer PET after Removal of the Original Surface: Influence of Raw Material

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Avaliação do módulo de elasticidade da madeira com uso de método não-destrutivo de vibração transversal

Numerosas pesquisas têm estudado os métodos não-destrutivos de avaliação de materiais e sua aplicação àqueles de matrizes complexas, como é o caso da madeira. Um dos primeiros métodos não-destrutivos investigados para aplicação nesses casos foi o da vibração transversal. Apesar de sua concepção simples, e a despeito dos grandes avanços obtidos nessa área com outros métodos, como, por exemplo, o ultra-som, o método de vibração transversal para a determinação do módulo de elasticidade da madeira revela-se como de grande potencial de aplicação, sobretudo pela precisão do modelo matemático a ele associado e pela possibilidade de sua aplicação a peças de dimensões estruturais (in-grade testing). Neste trabalho, apresenta-se o uso desse método na determinação do módulo de elasticidade de três espécies de eucalipto. Foram ensaiados não-destrutivamente e por ensaios mecânicos convencionais de flexão corpos-de-prova de 2 cm x 2 cm x 46 cm de E. grandis, E. saligna e E. citriodora. Os ensaios não-destrutivos foram conduzidos com uso do sistema BING - Beam Identification by Non-destructive Grading, que permite a análise das vibrações do material nos domínios do tempo e da freqüência. Os resultados obtidos revelaram boa correlação entre os dois tipos de ensaios empregados, justificando o início dos ensaios com peças de dimensões estruturais, para a viabilização da técnica nas práticas de classificação estrutural.

Treatment of PVC using an alternative low energy ion bombardment procedure

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Thermal analysis characterization of PAAm-co-MC hydrogels

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Measurement of Interfacial Porosity at the Acrylic Resin/Denture Tooth Interface

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Materiais cerâmicos de inserção aplicados a baterias de íons lítio

Esta revisão visa ser uma introdução à aplicação de materiais cerâmicos em dispositivos de armazenamento de energia, em especial baterias secundárias de íons lítio, dispositivos nos quais os materiais cerâmicos, especialmente óxidos, são muito importantes em todas as partes do dispositivo. A revisão está focada nos materiais cerâmicos para catodos e anodos, partes chaves destes dispositivos. Ela tem por principal finalidade ser uma fonte de informação para aqueles que desejem trabalhar com o desenvolvimento de materiais cerâmicos para tais tipos de dispositivos. Aspectos relacionados à nanotecnologia e materiais óxidos nanoestruturados para esta área são discutidos ao final do artigo.

Avaliação de recomendações normativas sobre o uso de ensaios no controle de qualidade de fabricação de geossintéticos

A utilização de materiais poliméricos designados por geossintéticos tem aumentando significativamente nos últimos anos na Engenharia Civil. Para desempenhar adequadamente a função para a qual foram projetados, os geossintéticos devem ser submetidos a um rigoroso processo de controle de qualidade durante a fabricação. Discussões sobre a freqüência e os principais tipos de ensaios de laboratório utilizados nesse processo de controle para dois tipos de geossintéticos, os geotêxteis e as geomembranas, os materiais mais utilizados da famíla dos geossintéticos, são abordados no presente trabalho. As análises efetuadas com base em normas disponíveis no Brasil, nos EUA e na Europa mostram que no cenário nacional não há recomendações normativas sobre o controle de qualidade para a maioria das aplicações de geotêxteis e geomembranas, sendo o assunto pouco discutido na literatura técnica. No cenário internacional, as normas Européias se destacam como o conjunto de práticas mais completo para ensaios de controle de qualidade de fabricação, considerando os diversos tipos de aplicação dos geossintéticos na Engenharia Civil.

Synthesis and properties of branched polyethylene/high-density polyethylene blends using a homogeneous binary catalyst system composed of early and late transition metal complexes

Branched polyethylene/high-density polyethylene blends (BPE/HDPE) with a wide range of molecular weights, melt flow indexes (MFI), and intrinsic viscosity were prepared using the homogeneous binary catalyst system composed by Ni(alpha-diimine)Cl-2 (1) (alpha-diimine = 1,4-bis(2,6-diisopropylphenyl)-acenaphthenediimine) and {Tp(Ms*)} TiCl3 (2) (Tp(Ms*)=hydridobis(3-mesitylpyrazol-1-yl)(5-mesityl-pyrazol-1-yl)) activated with MAO and/or TIBA in hexane at two different polymerization temperatures (30 and 55 degreesC) and by varying the nickel loading molar fraction (x(Ni)). At all Temperatures, a non-linear correlation between the x(Ni) and the productivity was observed, suggesting the occurrence of a synergistic effect between the nickel and the titanium catalyst precursors, which is more pronounced at 55 degreesC. The molecular weight of the BPE/HDPE blends considerably decreases with increasing Al/M molar ratio. The melt flow indexes (MFI) and intrinsic viscosities (eta) are strongly affected by x(Ni), but the melting temperatures are nearly constant, 132 +/- 3 degreesC. Dynamic mechanical thermal analysis (DMTA) shows the formation of different polymeric materials where the stiffness vanes according, to the x(Ni) and temperature used in the polymerization reaction. The surface morphology of the BPE/HDPE blends studied by scanning electron microscopy (SEM) revealed a low miscibility between the PE phases resulting in the formation of a sandwich structure after etching with o-xylene.

Study of the effect of the peptide loading and solvent system in SPPS by HRMAS-NMR

The SPPS methodology has continuously been investigated as a valuable model to monitor the solvation properties of polymeric materials. In this connection, the present work applied HRMAS-NMR spectroscopy to examine the dynamics of an aggregating peptide sequence attached to a resin core with varying peptide loading (up to 80%) and solvent system. Low and high substituted BHAR were used for assembling the VQAAIDYING sequence and some of its minor fragments. The HRMAS-NMR results were in agreement with the swelling of each resin, i.e. there was an improved resolution of resonance peaks in the better solvated conditions. Moreover, the peptide loading and the attached peptide sequence also affected the spectra. Strong peptide chain aggregation was observed mainly in highly peptide loaded resins when solvated in CDCl3. Conversely, due to the better swelling of these highly loaded resins in DMSO, improved NMR spectra were acquired in this polar aprotic solvent, thus enabling the detection of relevant sequence-dependent conformational alterations. The more prominent aggregation was displayed by the VQAAIDYING segment and not by any of its intermediary fragments and these findings were also corroborated by EPR studies of these peptide-resins labelled properly with an amino acid-type spin probe. Copyright (c) 2005 European Peptide Society and John Wiley & Sons, Ltd.

Osteointegration of poly(L-lactic acid)PLLA and poly(L-lactic acid)PLLA/poly(ethylene oxide)PEO implants in rat tibiae

Natural or synthetic materials may be used to aid tissue repair of fracture or pathologies where there has been a loss of bone mass. Polymeric materials have been widely studied, aiming at their use in orthopaedics and aesthetic plastic surgery. Polymeric biodegradable blends formed from two or more kinds of polymers could present faster degradation rate than homopolymers. The purpose of this work was to compare the biological response of two biomaterials: poly(L-lactic acid)PLLA and poly(L-lactic acid)PLLA/poly(ethylene oxide)PEO blend. Forty four-week-old rats were divided into two groups of 20 animals, of which one group received PLLA and the other PLLA/PEO implants. In each of the animals, one of the biomaterials was implanted in the proximal epiphysis of the right tibia. Each group was divided into subgroups of 5 animals, and sacrificed 2, 4, 8 and 16 weeks after surgery, respectively. Samples were then processed for analysis by light microscopy. Newly formed bone was found around both PLLA and PLLA/PEO implants. PLLA/PEO blends had a porous morphology after immersion in a buffer solution and in vivo implantation. The proportion 50/50 PLLA/PEO blend was adequate to promote this porous morphology, which resulted in gradual bone tissue growth into the implant.

Acrylonitrile-butadiene-styrene toughened nylon 6: The influences of compatibilizer on morphology and impact properties

Polymer alloys have been used as an alternative to obtain polymeric materials with unique physical properties. Generally, the polymer mixture is incompatible, which makes it necessary to use a compatibilizer to improve the interracial adhesion. Nylon 6 (PA6) is an attractive polymer to use in engineering applications, but it has processing instability and relatively low notched impact strength. In this study, the acrylonitrile-butadiene-styrene (ABS) triblock copolymer was used as an impact modifier for PA6. Poly(methyl methacrylate-co-maleic anyhydride) (MMA-MA) and poly(methyl methacrylate-co-maleic methacrylate) (MMA-GMA) were used as compatibilizers for this blend. The morphology and impact strength of the blends were evaluated as a function of blend composition and the presence of compatibilizers. The blends compatibilized with maleated copolymer exhibited an impact strength up to 800 J/m and a morphology with ABS domains more efi8ciently dispersed. Moderate amounts of MA functionality in the compatibilizer (∼5%) and small amounts of compatibilizer in the blend (∼5%) appear sufficient to improve the impact properties and ABS dispersion. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 87.

Non-labile plant C contributes to long-lasting macroaggregation of an Oxisol

Decomposition of plant material influences soil aggregation dynamics in ways that are still poorly understood, especially for Oxisols, in which oxides are believed to play a dominant role. In an incubation experiment, we investigated (i) the effect of plant material addition from selected monocot and dicot species on soil organic C (SOC), carbohydrate composition, fungal and total microbial biomass, and aggregation of an Oxisol; and (ii) the relationship among these properties and C mineralization patterns. The experiment was carried out at 25 °C for 180 d after addition of 11 plant materials (4 g C kg-1 soil) and a control (no plant material added). Mineralization of C during the incubation was described considering two pools of C (labile and non-labile) using a first-order plus linear fitting. Compared to the control, corn materials showed larger pentose input, greater mineralization rates for the non-labile C pool (k), greater soil pentose content (xylose + arabinose) and larger mean weight diameter of soil water-stable aggregates at 180 d of incubation. These effects were independent of changes in SOC content, suggesting that total C accrual and macroaggregation may be decoupled processes in this Oxisol. Our results support the hypothesis that the non-labile plant C pool contributes to the long-lasting stability of macroaggregates of this Oxisol and that this effect is mediated by plant and soil pentoses. We propose that plant pentose content and the decomposition rate of the slow pool (k) are useful parameters for the prediction of plant effects on aggregation dynamics of Oxisols and the selection of soil conservation practices. © 2012.