Air-particle abrasion on zirconia ceramic using different protocols: Effects on biaxial flexural strength after cyclic loading, phase transformation and surface topography

This study evaluated the effect of different air-particle abrasion protocols on the biaxial flexural strength and structural stability of zirconia ceramics. Zirconia ceramic specimens (ISO 6872) (Lava, 3M ESPE) were obtained (N=336). The specimens (N=118, n=20 per group) were randomly assigned to one of the air-abrasion protocols: Gr1: Control (as-sintered); Gr2: 50 μm Al2O3 (2.5 bar); Gr3: 50 μm Al2O3 (3.5 bar); Gr4: 110 μm Al2O3(2.5 bar); Gr5: 110 μm Al2O3 (3.5 bar); Gr6: 30 μm SiO2 (2.5 bar) (CoJet); Gr7: 30 μm SiO2(3.5 bar); Gr8: 110 μm SiO2 (2.5 bar) (Rocatec Plus); and Gr9: 110 μm SiO2 (3.5 bar) (duration: 20 s, distance: 10 mm). While half of the specimens were tested immediately, the other half was subjected to cyclic loading in water (100,000 cycles; 50 N, 4 Hz, 37 °°C) prior to biaxial flexural strength test (ISO 6872). Phase transformation (t→m), relative amount of transformed monoclinic zirconia (FM), transformed zone depth (TZD) and surface roughness were measured. Particle type (p=0.2746), pressure (p=0.5084) and cyclic loading (p=0.1610) did not influence the flexural strength. Except for the air-abraded group with 110 μm Al2O3 at 3.5 bar, all air-abrasion protocols increased the biaxial flexural strength (MPa) (Controlnon-aged: 1030±153, Controlaged: 1138±138; Experimentalnon-aged: 1307±184-1554±124; Experimentalaged: 1308±118-1451±135) in both non-aged and aged conditions, respectively. Surface roughness (Ra) was the highest with 110 μm Al2O3(0.84 μm. FM values ranged from 0% to 27.21%, higher value for the Rocatec Plus (110 μm SiO2) and 110 μm Al2O3 groups at 3.5 bar pressure. TZD ranged between 0 and 1.43 μm, with the highest values for Rocatec Plus and 110 μm Al2O3 groups at 3.5 bar pressure. © 2013 Elsevier Ltd.

The effect of the solute on the structure, selected mechanical properties, and biocompatibility of Ti-Zr system alloys for dental applications

New titanium alloys have been developed with the aim of utilizing materials with better properties for application as biomaterials, and Ti-Zr system alloys are among the more promising of these. In this paper, the influence of zirconium concentrations on the structure, microstructure, and selected mechanical properties of Ti-Zr alloys is analyzed. After melting and swaging, the samples were characterized through chemical analysis, density measurements, X-ray diffraction, optical microscopy, Vickers microhardness, and elasticity modulus. In-vitro cytotoxicity tests were performed on cultured osteogenic cells. The results showed the formation essentially of the α′ phase (with hcp structure) and microhardness values greater than cp-Ti. The elasticity modulus of the alloys was sensitive to the zirconium concentrations while remaining within the range of values of conventional titanium alloys. The alloys presented no cytotoxic effects on osteoblastic cells in the studied conditions. © 2013 Elsevier B.V. All rights reserved.

Local order of Pb1-xLaxZr0.40Ti 0.60O3 ferroelectric ceramic materials probed by X-ray absorption and Raman spectroscopies

This paper reports on the structural characterization of Pb 1-xLaxZr0.40Ti0.60O3 (PLZT) ferroelectric ceramic compositions prepared by the conventional solid state reaction method. X-ray absorption spectroscopy (XAS) and Raman spectroscopy were used to probe the local structure of PLZT samples that exhibits a normal and relaxor ferroelectric behavior. From the Zr K-edge and Pb LIII-edge EXAFS spectra, a considerable dissymmetry of Zr and Pb sites was observed in all samples, including those showing a long-range order cubic symmetry and a relaxor behavior. The Raman spectroscopy results confirmed the existence of a local disorder in all PLZT samples through the observation of Raman active vibrational modes. The variation in the intensity of the E(TO 3) mode in the PLZT relaxor samples indicates that the process of correlation between nanodomains stabilizes at temperatures lower than T m. © 2013 Elsevier B.V. All rights reserved.

Análise comparativa da distribuição de tensões em incisivo central superior, restaurado com diferentes sistemas de pinos intra-radiculares

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Citotoxicidade e ação antimicrobiana do cimento Portland associado a diferentes agentes radiopacificadores

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Análise, modelagem e interpretação de dados gravimétricos no lineamento Guapiara - região sudeste do estado de São Paulo

Pós-graduação em Geologia Regional - IGCE

Caracterização mecânica, física e química das ligas Ti-35Nb-5Zr e Ti-35Nb-10Zr

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Resistência à flexão, resistência à tração diametral e dureza de sistemas cerâmicos para infra-estrutura

Pós-graduação em Reabilitação Oral - FOAR

Efeito do envelhecimento In Vitro na transformação de fase cristalina da Y-TZP: análise topográfica, mecânica e cristalográfica

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Efeito da escovação na formação in situ de biofilme dentário inicial e na rugosidade superficial em cerâmica de y-tzp após vitrificação e polimento

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Estudo da formação de espumas cerâmicas à base de zircônio a partir do processo sol-gel

Pós-graduação em Química - IQ

Síntese e caracterização de nanopartículas de ZrO2 por rota hidrotérmica

Pós-graduação em Ciência e Tecnologia de Materiais - FC

Efeitos da termoterapia induzida pela água na próstata: estudo experimental em cães

Pós-graduação em Bases Gerais da Cirurgia - FMB

Efeito do nitrogênio nas propriedades anelásticas de Nb e ligas Nb-1,0%pZr

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Aspectos biológicos e bioatividade de materiais a base de MTA em cultura de células

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)