Three-dimensional finite element analysis of stress distribution in retention screws of different crown-implant ratios

The retaining screw of the implant-supported dental prosthesis is the weakest point of the crown/implant system. Furthermore, crown height is another important factor that may increase the lever arm. Therefore, the aim of this study was to assess the stress distribution in implant prosthetic screws with different heights of the clinical crown of the prosthesis using the method of three-dimensional finite element analysis. Three models were created with implants (3.75 mm × 10 mm) and crowns (heights of 10, 12.5 and 15 mm). The results were visualised by means of von Mises stress maps that increased the crown heights. The screw structure exhibited higher levels of stresses in the oblique load. The oblique loading resulted in higher stress concentration when compared with the axial loading. It is concluded that the increase of the crown was damaging to the stress distribution on the screw, mainly in oblique loading. © 2013 Taylor & Francis.

Comparison of the accuracy for three dental impression techniques and index: An in vitro study

Objectives: This in vitro study compared the dimensional accuracy of stone index (I) and three impression techniques: tapered impression copings (T), squared impression copings (S) and modified squared impression copings (MS) for implant-supported prostheses. Methods: A master cast, with four parallel implant abutment analogs and a passive framework, were fabricated. Vinyl polysiloxane impression material was used for all impressions with two metal stock trays (open and closed tray). Four groups (I, T, S and MS) were tested (n = 5). A metallic framework was seated on each of the casts, one abutment screw was tightened, and the gap between the analog of implant and the framework was measured with a stereomicroscope. The groups' measurements (80 gap values) were analyzed using software (LeicaQWin - Leica Imaging Systems Ltd.) that received the images of a video camera coupled to a Leica stereomicroscope at 100× magnification. The results were statistically analyzed with Kruskal-Wallis One Way ANOVA on Ranks test followed by Dunn's Method, 0.05. Results: The mean values of abutment/framework interface gaps were: Master Cast = 32 μm (SD 2); Group I = 45 μm (SD 3); Group T = 78 μm (SD 25); Group S = 134 μm (SD 30); Group MS = 143 μm (SD 27). No significant difference was detected among Index and Master Cast (P = .05). Conclusion: Under the limitations of this study, it could be suggested that a more accurate working cast is possible using tapered impression copings techniques and stone index. © 2013 Japan Prosthodontic Society.

Extrusion of flavored corn grits: Structural characteristics, volatile compounds retention and sensory acceptability

The effects of the moisture content of the raw material, extrusion temperature and screw speed on flavor retention, sensory acceptability and structure of corn grits extrudates flavored with isovaleraldehyde, ethyl butyrate and butyric acid were investigated. Higher temperature resulted in more expanded extrudates with lower density and cutting force, while higher moisture content increased ethyl butyrate retention. The most acceptable extrudates were those obtained with low moisture content, under conditions of high extrusion temperature and high screw speed, or low screw speed and low extrusion temperature, whereas the aroma intensity closest to the ideal was observed under conditions of low extrusion temperature and low moisture content of the raw material. © 2013 Elsevier Ltd.

O efeito da orientação do parafuso bloqueado nas propriedades biomecânicas da placa S.P.S. Free-Block em corpos de prova nao osteoporóticos

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Avaliação de parafusos bioabsorvíveis na reparação de fraturas experimentais de sesamóides em eqüinos

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

A influência do design na aplicação de forças manuais para abertura de embalagens plásticas de refrigerantes

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Avaliação da influência de diferentes materiais oclusais na confecção de próteses fixas implantossuportadas unitárias com diferentes diâmetros dos implantes osseointegrados: estudo pelo método dos elementos finitos tridimensionais

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Influência do tipo de conector na união dente e implantes de hexágono interno e externo: estudo pelo método da fotoelasticidade

Pós-graduação em Odontologia - FOA

Caracterização fenotípica e genotípica de bactérias recuperadas de implante ortopédico de conjunto placa-parafuso e parafuso de aço inoxidável austenítico após remoção cirúrgica

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Influência da granulometria da matéria-prima e da configuração da extrusora no conteúdo de amido resistente, digestibilidade, fermentação intestinal e respostas metabólicas de cães

Pós-graduação em Zootecnia - FCAV

Farelo de algodão na nutrição de tilápias do Nilo na fase de terminação em tanques-rede

Pós-graduação em Zootecnia - FMVZ

Análise dos resultados do tratamento da mordida cruzada posterior funcional com o expansor fixo Hyrax

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Análise estrutural dos efeitos da desadaptação em componentes de próteses odontológicas utilizando o método dos elementos finitos com elemento de contato e pré-carga

Pós-graduação em Engenharia Mecânica - FEB

Estudo da distribuição das tensões geradas por implantes odontológicos com diferentes perfis de rosca

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Análise numérica de interfaces de próteses dentárias através da mecânica do dano

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)