Supercritical carbonation treatment on extruded fibre-cement reinforced with vegetable fibres

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Durable bonds at the adhesive/dentin interface: an impossible mission or simply a moving target?

Composite restorations have higher failure rates, more recurrent caries and increased frequency of replacement as compared to dental amalgam. Penetration of bacterial enzymes, oral fluids, and bacteria into the crevices between the tooth and composite undermines the restoration and leads to recurrent decay and failure. The gingival margin of composite restora tions is particularly vulnerable to decay and at this margin, the adhesive and its seal to dentin provides the primary barrier between the prepared tooth and the environment. The intent of this article is to examine physico-chemical factors that affect the integrity and durability of the adhesive/dentin interfacial bond; and to explore how these factors act synergistically with mechanical forces to undermine the composite restoration. The article will examine the various avenues that have been pursued to address these problems and it will explore how alterations in material chemistry could address the detrimental impact of physico-chemical stresses on the bond formed at the adhesive/dentin interface.

A new heterologous fibrin sealant as a scaffold to cartilage repair - experimental study and preliminary results

Autologous fibrin gel is commonly used as a scaffold for filling defects in articular cartilage. This biomaterial can also be used as a sealant to control small hemorrhages and is especially helpful in situations where tissue reparation capacity is limited. In particular, fibrin can act as a scaffold for various cell types because it can accommodate cell migration, differentiation, and proliferation. Despite knowledge of the advantages of this biomaterial and mastery of the techniques required for its application, the durability of several types of sealant at the site of injury remains questionable. Due to the importance of such data for evaluating the quality and efficiency of fibrin gel formulations on its use as a scaffold, this study sought to analyze the heterologous fibrin sealant developed from the venom of Crotalus durissus terrificus using studies in ovine experimental models. The fibrin gel developed from the venom of this snake was shown to act as a safe, stable, and durable scaffold for up to seven days, without causing adverse side effects. Fibrin gel produced from the venom of the Crotalus durissus terrificus snake possesses many clinical and surgical uses. It presents the potential to be used as a biomaterial to help repair skin lesions or control bleeding, and it may also be used as a scaffold when applied together with various cell types. The intralesional use of the fibrin gel from the venom of this snake may improve surgical and clinical treatments in addition to being inexpensive and adequately consistent, durable, and stable. The new heterologous fibrin sealant is a scaffold candidate to cartilage repair in this study.

Desenvolvimento e caracterização de dispositivos eletroluminescentes contendo uma blenda polimérica condutora e Zn2SiO4:Mn

Despite the great development of organic and polymeric electroluminescent materials, the large scale commercial application of devices made with these materials seems conditioned to specific cases, mainly due to the high cost and the low durability, in compared to conventional technologies. In this study was produced electroluminescent devices by a process simple, drop casting. Were produced electroluminescent films containing Zn2SiO4:Mn immersed in a conductive polymer blend with different thicknesses. The morphological characteristics of these films were studied by scanning electronic microscopy. These films were used in the manufacture of electroluminescent devices, in which the light emission properties of the developed material were evaluated. The blend was composed of the conductive polymer Poly(o-methoxyaniline), doped with p-toluene sulfonic acid, and an insulating polymer, Poly(vinylidene fluoride) and its copolymer Poly(vinylidene fluoride-cotrifluoroethylene). To this blend was added Zn2SiO4:Mn, thereby forming the composite. A first set of devices was obtained using composites with different weight fraction of polymeric and inorganic phases, which were deposited by drop casting over ITO substrates. Upper electrodes of aluminum were deposited by thermal evaporation. The resulting device architecture was a sandwich type structure ITO/ composite/ Al. A second set of devices was obtained as self-sustaining films using the best composite composition obtained for the device of the first set. ITO electrodes were deposited by RF-Sputtering, in both faces of these films. The AC electrical characterization of the devices was made with impedance spectroscopy measurements, and the DC electrical characterization was performed using a source/ meter unit Keithley 2410. The devices light emission was measured using a photodiode coupled to a digital electrometer, Keithley 6517A. The devices electrooptical characterization showed that the...

Propriedades ópticas e elétricas de materiais híbridos de sílica/orgânico à base de GPTS:TEOS preparados pelo método sol-gel

Fabrication of optoelectronic devices requires the employment of at least one transparent electrode. Usually, commercially transparent electrodes have been made by deposition of indium tin oxide (ITO) films by RF-Sputtering technique. These commercial electrodes have sheet resistance of about 100 Ω/sq and optical transmittance of 77% at the wavelength of 550 nm. The poly(3,4-ethylenedioxythiophene):polystyrene-sulfonate (PEDOT:PSS) is an alternative material to fabricate transparent electrodes due to its high conductivity (about 600 S/cm) and solubility in water. Soluble conductive materials exhibits advantages for processing of electrode layers, however there is a disadvantage during devices fabrication once materials with the same solvent of the electrode material cannot be coated one over the other. Alternatively, organic/Silica hybrid materials prepared by sol-gel process allow producing bulks and films with high chemical durability. In order to obtain transparent electrodes with high chemical durability, we introduced a blended material comprising the high UV-VIS transparency of organic/Silica sol-gel material and a high conductivity polymer PEDOT:PSS. The organic/Silica sol was obtained using two different molar concentrations (1:1 and 4:1), of tetraethylorthosilicate (TEOS) and 3-glycidoxypropyltrimethoxysilane (GPTS). Amounts of PEDOT:PSS solutions were added to the sol material, resulting in different weight fractions of sol and polymer. G:T/P:P were deposit onto glass substrates by spray-coating. In order to perform electrical characterization of the blended material, gold electrodes were thermally evaporated onto the films. The electrical characterization was performed using a Keithley 2410 source/meter unity and the optical characterization, using a Cary50 UV-Vis spectrophotometer. The absorption coefficient and electric conductivity of the different compositions blends, as function of the PEDOT:PSS concentration, were...

Análise de falhas por fadiga num rotor de hidrogerador vertical via método dos elementos finitos

Pós-graduação em Engenharia Mecânica - FEG

Chromatic stability of acrylic resins of artificial eyes submitted to the accelerated aging and polishing

Esthetics and durability of materials used to fabricate artificial eyes has been an important issue since artificial eyes are essential to restore esthetics and function, protect the remaining tissues and help with patients' psychological therapy. However, these materials are submitted to degrading effects of environmental agents on the physical properties of the acrylic resin. OBJECTIVE: This study assessed the color stability of acrylic resins used to fabricate sclera in three basic shades (N1, N2 and N3) when subjected to accelerated aging, mechanical and chemical polishing. MATERIAL AND METHODS: Specimens of each resin were fabricated and submitted to mechanical and chemical polishing. Chromatic analysis was performed before and after accelerated aging through ultraviolet reflection spectrophotometry. RESULTS: All specimens revealed color alteration following polishing and accelerated aging. The resins presented statistically significant chromatic alteration (p<0.01) between the periods of 252 and 1008 h. CONCLUSIONS: Both polishing methods presented no significant difference between the values of color derivatives of resins.

Marginal deterioration of the silicone for facial prosthesis with pigments after effect of storage period and chemical disinfection

The failure of facial prostheses is caused by limitations in the properties of existing materials, especially flexibility and durability. Therefore, this study evaluated the marginal deterioration of a silicone used for fabrication of facial prostheses (Silastic MDX4-4210, Dow Corning Corporation, Midland, MI, USA) according to the influence of artificial aging, daily disinfection, and 2 types of pigmentation. Thirty specimens were fabricated and subdivided in 6 groups: without pigmentation, pigmented with make-up powder and iron oxide, and evaluated with and without the action of the disinfectant. Analysis of marginal deterioration was performed on a scanning electron microscope (magnification, ×5000) immediately 6 months and 1 year after fabrication of specimens, following the guidelines of ASTM International. After visual analysis of the photomicrographs, it was noticed that all groups presented marginal deterioration and alterations in surface texture with time. The use of disinfection did not contribute to the marginal deterioration of polymer (silicone), regardless of the pigmentation and artificial aging.

Reconhecimento da perda de eficácia de protetor intra-auricular

Among the harmful health agents, it is given to the noise, one of the most present in urban and social environments. There are efficient measures to control the noise and the auricular Individual Protection Equipment (IPEa) is the most used. It has been observed the shortage in the comfortable and functional individual auditory protection products, related to durability, face to the efficiency right of the equipment. The main objective of this study was to recognize if there is effectiveness loss toward the used time on the Auditory Equipment, intra-auricular Individual Protection, of foam (3M), model 1110. It has been verified that the equipments suffer efficiency alteration according to the time of use, and the material consuming initiates reliable loss, mainly in audible frequencies going up to 100Hz, and from 16 days for sonorous pressure suffered started in 101dB 20Hz. For sonorous pressure suffered from 107dB to 20Hz, the reliable loss for the usage was of 8 days. The IPEas do not lose effectiveness on important attenuation by the daily use in frequencies from 1KHz until 20KHz. It has been concluded that there is effectiveness loss, according to the daily and frequent use of the IPEa studied.

Growth Control of Microbial in Miscible Cutting Fluids Using Ultraviolet Radiation

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Evaluation of a plastic composite produced with residues of sugarcane bagasse and polypropylene without additives

In this research the aim was produce and evaluate a plastic composite using recycled polypropylene (PP) and fibers from sugarcane bagasse residues (SC), without the use of additives. This analysis was based on laboratorial tests for physical and mechanical characterization, according to the standards ASTM D256-00, D638-101 and D570-98 were analyzed: water absorption, thickness swelling, impact resistance, tensile strength and its correspondent deformation. For comparison it was elaborated three different compositions: 100% PP; 80% PP+20%SC; 70%PP+30%SC. The results indicate a positive correlation with the content of fiber and water absorption and thickness swelling. In the tension tests, the composites with fibers increase the value of resistance for physical efforts, bringing advantages as durability and integrity of the material, showing a viability of the composites.

Evaluation of a plastic composite produced with residues of sugarcane bagasse and polypropylene wihtout additives

In this research the aim was produce and evaluate a plastic composite using recycled polypropylene (PP) and fibers from sugarcane bagasse residues (SC), without the use of additives. This analysis was based on laboratorial tests for physical and mechanical characterization, according to the standards ASTM D256-00, D638-101 and D570-98 were analyzed: water absorption, thickness swelling, impact resistance, tensile strength and its correspondent deformation. For comparison it was elaborated three different compositions: 100% PP; 80% PP+20%SC; 70%PP+30%SC. The results indicate a positive correlation with the content of fiber and water absorption and thickness swelling. In the tension tests, the composites with fibers increase the value of resistance for physical efforts, bringing advantages as durability and integrity of the material, showing a viability of the composites.

Lisianthus vase life after 1-methylcyclopropene and salicylic acid postharvest treatment

This study evaluated the effects of application of 0.5 µl L-1 1-methyl-cyclopropene (1-MCP), 1000 mg L-1 salicylic acid (SA) and the interaction between the two products at room temperature and pre-exposure at 9±2°C for 24 h in maintaining postharvest quality of lisianthus flowers. After applying the treatment, the flowers were kept in jars with water, stored at 24±2°C. The SA treatments proved ineffective, presenting symptoms of phytotoxicity, with high rate of bent neck and yellowing of petals, both at room temperature and in cold storage, and propitiate the emergence of pathogens. The association between 1-MCP in pre-exposure to 9±2°C for 24 h increased the durability of the stems in six days compared to the control treatment, with less symptoms of bent neck and swelling of stems.

Conservação de goiabas ‘Pedro Sato’ minimamente processadas e irradiadas

The aim of this study was to evaluate the effect of gamma irradiation associated with modified atmosphere in cold storage of guava ‘Pedro Sato’ minimally processed, checking their physical-chemical characteristics. Were used guavas from the region of Vista Alegre do Alto/São Paulo/Brazil. After harvest, fruits were immediately transported to the Fruit and Vegetables Laboratory from the Agroindustrial Management and Technology Department, Agronomic Sciences College - UNESP - Botucatu / SP, where they were kept at 10 ° C and 90-95% RH in cold storage, for 12 days. In the laboratory, fruits were selected by size and lack of defects in order to standardize the lot and then were cut into slices 0.5 cm thick. We used the completely randomized design, with factorial design 5 x 5, with three replications. The first factor consisted of the following effects: control 1 (without package or irradiation), control 2 (polystyrene package/PS + package low density polyethylene/LDPE and without irradiation), treatment 1 (PS + LDPE and 0.2 kGy ), treatment 2 (PS + LDPE and 0.6 kGy) and treatment 3 (PS + LDPE and 1.0 kGy). The second factor consisted of the evaluation periods: 0, 3, 6, 9 and 12 days. The analyses were: firmness, soluble solids (SS), titratable acidity (TA), maturity index, pH, breathing behavior. In the end of this work it was concluded that the lower dose of radiation associated with modified atmosphere promoted positive effect on physical-chemical characteristics of guava ‘Pedro Sato’, providing fruits with higher quality and durability, due to higher maintenance of pulp firmness, the highest pH and soluble solids obtained. Regarding the storage days, there were no beneficial effect of the treatments during storage, mainly due to the sensitivity of fruits submitted to gamma irradiation, where only the early days provided better values for the variables.

Análise de misturas solo-agregado reciclados de resíduos sólidos da construção civil, para fins de pavimentação de vias urbanas de baixo volume de tráfego

This work deals with the continuation of Scientific Initiation research initiated by Tamura (2012), which draws up a mixture of soil and recycled aggregate analysis for paving of low traffic volume roads using local materials from the Vale do Paraíba region. The main steps of the process were the soil and recycled aggregate characterization, along with grading tests and California Bearing Ratio (CBR) applied to the soil, the recycled aggregate and the mixture of soil and recycled aggregate; aiming their use as base and sub-base in paving urban roads. The results are discussed, emphasizing the mechanical behavior. The current results are compared with the results of IC Tamura research, taking decisions over this job to the final product best result. For a greater understanding of the work in general were described paving, its structure, its components and its physical behavior. It has been intended to emphasize the importance of the mixture of soil and recycled aggregate to meet the quality requirements and compliance with the specifications of current technical standards, in the context of durability, natural materials economy, decreases volume in landfills and cost reduction