Effect of drying method on the sorption isotherms and isosteric heat of persimmon pulp powder

Moisture equilibrium data of persimmon pulp powders with 50% maltodextrin (dry basis) obtained with different drying methods were determined at 20, 30, 40 and 50 degrees C. The spray-dryer gave a dry product with a higher adsorption capacity than the other methods. The vacuum- and freeze-dried products had the same adsorption capacity. The highest isosteric heat of sorption was observed for powders produced by spray-drying. The isokinetic temperature (T(B)) calculated for persimmon pulp powder obtained by vacuum-, spray- and freeze-drying were 541.4 K, 616.3 K, 513.2 K, respectively. The sorption process was spontaneous and enthalpy controlled.

Evaluation of dental pulp repair using low level laser therapy (688 nm and 785 nm) morphologic study in capuchin monkeys

The aim of this study was to evaluate the hypothesis that low-level laser therapy (LLLT) 688 nm and 785 nm accelerate dentin barrier formation and repair process after traumatic pulp exposure. The sample consisted of 45 premolars of capuchin monkeys (Cebus apella) with pulp exposure Class V cavities. All premolars were treated with calcium hydroxide (Ca(OH)(2)), divided in groups of 15 teeth each, and analyzed on 7(th), 25(th), and 60(th) day. Group GI - only Ca(OH)(2), GIF- laser 688 nm, and GIII - laser 785 nm. Laser beam was used in single and punctual dose with the parameters: continuous, 688 nm and 785 nm wavelength, tip's area of 0.00785 cm(2), power 50 mW, application time 20 s, dose 255 J/cm(2), energy 2 J. Teeth were capped with Ca(OH)(2), Ca(OH)(2) cement and restored with amalgam. All groups presented pulp repair. on 25(th) day the thickness of the formed dentin barrier was different between the groups GI and GII (p < 0.05) and between groups GI and GIII (p < 0.01). on 60(th) day there was difference between GI and GIII (p < 0.01). It may be concluded that, LLLT 688 nm and 785 nm accelerated dentin barrier formation and consequently pulp repair process, with best results using infrared laser 785 nm. (c) 2009 by Astro Ltd. Published exclusively by WLLEY-VCH Verlag GmbH & Co. KGaA

A neural network-based preset generation tool for a steel tandem cold mill

This paper traces the development of a software tool, based oil a combination of artificial neural networks (ANN) and a few process equations. aiming to serve as a backup operation instrument in the reference generation for real-time controllers of a steel tandem cold mill By emulating the mathematical model responsible for generating presets under normal operational conditions, the system works as ail option to maintain plant operation in the event of a failure in the processing unit that executes the mathematical model. The system, built from the production data collected over six years of plant operation, steered to the replacement of the former backup operation mode (based oil a lookup table). which degraded both product quality and plant productivity. The study showed that ANN are appropriated tools for the intended purpose and that by this instrument it is possible to achieve nearly the totality of the presets needed by this land of process. The text characterizes the problem, relates the investigated options to solve it. justifies the choice of the ANN approach, describes the methodology and system implementation and, finally, shows and discusses the attained results. (C) 2009 Elsevier Ltd. All rights reserved

Heat-killed Enterococcus faecalis Alters Nitric Oxide and CXCL12 Production but not CXCL8 and CCL3 Production by Cultured Human Dental Pulp Fibroblasts

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Nutrient digestibility of degermed, dehulled corn, citrus pulp, and soy protein concentrate by barrows

This study was carried out to determine apparent ileal digestibility (AID) and apparent total tract digestibility (ATTD) of DM, CP, GE, and their respective digestible content of degermed dehulled corn (Zea mays), citrus pulp, and soy (Glycine max) protein concentrate by pigs using the difference method. Thirty-two barrows (28.1 +/- 1.6 kg of BW) were fed a corn-soybean meal basal diet or 1 of 3 diets formulated by replacing 30% of the basal diet with 30% of 1 of the test feedstuffs for 11 d. Chromic oxide (0.3%) was included in the diets. Feces were collected from days 7 to 11 by grab sampling and ileal digesta were collected after pigs were slaughtered on day 12. The AID of DM and AID and ATTD of GE of degermed corn (77.4, 88.7, and 77.7%) were greater (P < 0.05) than those observed in citrus pulp (50.3, 86.5, and 55.8%) and in soy protein concentrate (63.5, 85.1, and 59.4%), which did not differ (P > 0.05). The ATTD of CP, total digestible CP, and total DE of soy protein concentrate (87.5%, 500 g/kg, and 3739 kcal/kg) were higher (P < 0.05) than the values in degermed corn (81.7%, 57.5 g/kg, and 3330 kcal/kg), which were greater (P < 0.05) than those in citrus pulp (60.5%, 39.5 g/kg, and 3223 kcal/kg). Total and ileal digestible DM, AID of CP, and ileal DE of degermed corn (782 g/kg, 673 g/kg, 70.7%, and 2913 kcal/kg) and soy protein concentrate (778 g/kg, 570 g/kg, 78.7%, and 2878 kcal/kg) were similar (P > 0.05) and greater (P < 0.05) than those in citrus pulp (737 g/kg, 436 g/kg, 50.6%, and 2081 kcal/kg). Ileal digestible CP of degermed corn (49.8 g/kg) and citrus pulp (33.0 g/kg) did not differ (P > 0.05) but were smaller (P < 0.05) than the value found in soy protein concentrate (434 g/kg). The DM and energy from degermed corn are more efficiently digested by the pig than those from soy protein concentrate and citrus pulp. Soy protein concentrate was the best protein source evaluated in this study.

Use of fungal inocula and pumice for decomposing coffee pulp

A study of decomposition of coffee pulp (from Guatemala City, Guatemala) was carried out with several inocula. Fresh and pressed pulps were studied in field and laboratory experiments. Results showed that the best inoculum among the eight examined in the experiments was the fungus Trichoderma viride, the only one not isolated from the coffee pulp itself. This inoculum, together with pumice, accelerated the decomposition of coffee pulp at ambient temperature during a 45-day test period. © 1985.

Biocompatibility of an adhesive system applied to exposed human dental pulp

Human pulp tissue was directly capped with All Bond 2, or calcium hydroxide and evaluated 7, 30, or 60 days after the procedures. Histological analysis was performed to assess the inflammatory cell response, tissue disorganization, dentin bridging, and the presence of bacteria. At 7 days, with All Bond 2 capping, there was a large area of neutrophilic infiltrate underlying the pulp capping material, and the death of adjacent odontoblasts, was observed. However, with time, the neutrophilic reaction was replaced by fibroblastic proliferation with macrophages and giant cells surrounding globules of resin scattered in the coronal pulp tissue. The persistent inflammatory reaction and hyaline alteration of extracellular matrix inhibited complete pulp repair or dentin bridging. In contrast, at 7 days, the pulp tissue capped with calcium hydroxide exhibited odontoblast-like cells organized underneath coagulation necrosis. Pulp repair evolved into apparent complete dentin bridge formation at 60 days. All Bond 2 did not appear to allow any pulp repair and does not appear to be indicated for direct pulp capping of human teeth. Copyright © 1999 by The American Association of Endodontists.

Water sorption thermodynamic properties applied to persimmon skin and pulp

Moisture equilibrium data of persimmon skin and pulp were determined using the static gravimetric method. Adsorption and desorption isotherms were obtained in the range of 20-70°C, to water activities (a w) from 0.02 to 0.85. The application of the GAB model to the experimental results, using direct nonlinear regression analysis, provided a good agreement between experimental and calculated values. The net isosteric heat of sorption was estimated from equilibrium sorption data, using the Clausius-Clapeyron equation. Isosteric heats of sorption were found to increase with increasing temperature and could be well adjusted by an exponential relationship. The enthalpy-entropy compensation theory was applied to sorption isotherms and plots of ΔH versus ΔS for skin and pulp provided the isokinetic temperatures, indicating an enthalpy controlled sorption process. © 2000 Elsevier Science B.V.

Healing process of dog dental pulp after pulpotomy and pulp covering with mineral trioxide aggregate or Portland cement.

Considering several reports about the similarity between the chemical compositions of the mineral trioxide aggregate (MTA) and Portland cement (PC), the subject of this investigation was to analyze the behavior of dog dental pulp after pulpotomy and direct pulp protection with these materials. After pulpotomy, the pulp stumps of 26 roots of dog teeth were protected with MTA or PC. Sixty days after treatment, the animal was sacrificed and the specimens removed and prepared for histomorphological analysis. There was a complete tubular hard tissue bridge in almost all specimens. In conclusion, MTA and PC show similar comparative results when used in direct pulp protection after pulpotomy.

Composição fitoquímica dos óleos essenciais de folhas de Lippia alba (Mill.)N.E.Br. em diferentes épocas de colheita e partes do ramo

This work aimed to determine the best harvest time for biomass production, yield and essential oil composition considering the seasonal variation (spring, summer, autumn and winter) on different plant parts (apical, medial and basal). Essential oils were extracted by hydro-distillation with a Clevenger apparatus for both fresh and dry mass obtained in field and lab conditions respectively. The extracted essential oils were analyzed by GS/MS (Shimadzu, QP-5000). The chemical components were identified by comparing their mass spectrum to the patterns filed in the MS computer memory (Wiley,139,Lib.), to the literature references, and by co-injection with authentic standards. Applying phyto-chemical tests on fresh and dry mass, the chemical component percentages of essential oils were calculated and identified as follows: citral (neral and geranial), myrcene, caryophylene and elemene.

Effect of substrata on the development of stem cuttings of Lippia alba (Mill.) N. E. BR. - Limonene-carvone chemotype

Studies were conducted to show the effect of different substrata on the development of stem cuttings of Lippia alba made of limonene-carvone chemotype. The experiment was done in the College of Agronomical Sciences, UNESP, Botucatu, SP, Brazil in 2000. The cuttings were planted in polystyrene trays consisting of 72 cells. The cuttings had about 0.20 m of length and were put in the following substrata: Fine sand (T1), commercial substratum (T2), carbonised rice peel and local soil (T3), local soil, cow manure and carbonised rice peel (T4), vermiculite (T5), and carbonised rice peel (T6). After 40 days the development of stem cuttings were evaluated. High rate of rooting of stem cuttings was verified, with average of 95% and no significant difference between the treatments. In relation to dry mass of aerial parts and dry mass of roots, significant differences were found. For dry mass production of aerial parts the commercial substratum (T2) and the local soil, cow manure, carbonised rice peel (T4) were optimal. For mass of roots the local soil, cow manure, carbonised rice peel (T4) proved to be the best.

Effect of Bacillus circulans D1 thermostable xylanase on biobleaching of eucalyptus kraft pulp

The alkalophilic Bacillus circulans D1 was isolated from decayed wood. It produced high levels of extracellular cellulase-free xylanase. The enzyme was thermally stable up to 60°C, with an optimal hydrolysis temperature of 70°C. It was stable over a wide pH range (5.5-10.5), with an optimum pH at 5.5 and 80% of its activity at pH 9.0. This cellulase-free xylanase preparation was used to biobleach kraft pulp. Enzymatic treatment of kraft pulp decreased chlorine dioxide use by 23 and 37% to obtain the same kappa number (κ number) and brightness, respectively. Separation on Sephadex G-50 isolated three fractions with xylanase activity with distinct molecular weights.

A compostagem como processo catalisador para a reutilização dos resídues de fábrica de celulose e papel

Recognizing the great potential of this residue to increase the eucalyptus forests produtivity - when used in its humidified form - the main objective of this project was to decompose the solid residues generated at Luiz Antonio mill, in a fast and artificial way, by means of piles or ridges of composted materials. The materials used in this composting process were: activated sludge, dregs and grits, wood ash and biomass. Applications of both phosphorus and potassium have been used during the planting phase. Nitrogen, in the form of urea, has been applied in two treatments with the main purpose to decrease the C/N ratio and to speed up the decomposition process. The experiment was carried out in 120 days. The best results were obtained in residue piles with a 3:1 ratio, i.e., 75% residues + 25% biomass. This mixture provided an extremely good aeration, thus enabling an appropriate material mixing and homogenization. Under the technological viewpoint, the results obtained from the composting process were quite satisfactory for VCP industrial residues treatment. This composting process enabled a material accelerated stabilization (lower C/N ratio) and homogenization. After this experiment, it became possible to use all residues just as they were generated by Luiz Antônio pulp and paper mill. This project is of the utmost relevance to VCP's forestry department as far as a significant amount of nutrients is getting back to the soil in the form of mineral and organic materials.

In vitro penetration of bleaching agents into the pulp chamber

Aim: To investigate pulp chamber penetration of bleaching agents in teeth following restorative procedures. Methodology: Bovine lateral incisors were sectioned 3 mm apical to the cemento-enamel junction and the coronal pulpal tissue was removed. Teeth were divided into six groups (n = 10): G1, G2 and G3 were not submitted to any restorative procedure, while G4, G5 and G6 were submitted to Class V preparations and restored with composite resin. Acetate buffer was placed in the pulp chamber and treatment agents were applied for 60 min at 37°C as follows: G1 and G4, immersion into distilled water; G2 and G5, 10% carbamide peroxide (CP) exposure; G3 and G6, 35% CP bleaching. The buffer solution was removed and transferred to a glass tube where leuco crystal violet and horseradish peroxidase were added, producing a blue solution. The optical density of the blue solution was determined spectrophotometrically at 596 nm. A standard curve made with known amounts of hydrogen peroxide was used to convert the optical density values of the coloured samples into microgram equivalents of hydrogen peroxide. Data were submitted to ANOVA and Tukey's test (5%). Results: Amounts of hydrogen peroxide found in the pulp chamber of G2 and G5 specimens (0.1833 ± 0.2003 μg) were significantly lower (P = 0.001) when compared to G3 and G6 specimens (0.4604 ± 0.3981 μg). Restored teeth held significantly higher (P = 0.001) hydrogen peroxide concentrations in the pulp chamber than intact teeth. Conclusion: Higher concentrations of the bleaching agent produced higher levels of hydrogen peroxide in the pulp chamber, especially in restored teeth.