The Lactate Minimum Test protocol provides valid measures of cycle ergometer VO2 peak

Aim. The aim of the present study was to investigate the validity of the Lactate Minimum Test (LMT) for the determination of peak VO2 on a cycle ergometer and to determine the submaximal oxygen uptake (VO2) and pulmonary ventilation (VE) responses in an incremental exercise test when it is preceded by high intensity exercise (i.e., during a LMT).Methods. Ten trained male athletes (triathletes and cyclists) performed 2 exercise tests in random order on an electromagnetic cycle ergometer: 1) Control Test (CT): an incremental test with an initial work rate of 100 W, and with 25 W increments at 3-min intervals, until voluntary exhaustion; 2) LMT: an incremental test identical to the CT, except that it was preceded by 2 supramaximal bouts of 30-sec (similar to120% VO(2)peak) with a 30-sec rest to induce lactic acidosis. This test started 8 min after the induction of acidosis.Results. There was no significant difference in peak VO2 (65.6+/-7.4 ml.kg(-1).min(-1); 63.8+/-7.5 ml.kg(-1).min(-1) to CT and LMT, respectively). However, the maximal power output (POmax) reached was significantly higher in CT (300.6+/-15.7 W) than in the LMT (283.2+/-16.0 W).VO2 and VE were significantly increased at initial power outputs in LMT.Conclusion. Although the LMT alters the submaximal physiological responses during the incremental phase (greater initial metabolic cost), this protocol is valid to evaluate peak VO2, although the POmax reached is also reduced.

Immunization of bovines using a DNA vaccine (pcDNA3.1/MSP1b) prepared from the jaboticabal strain of Anaplasma marginale

Anaplasma is a tick-borne ehrlichial pathogen of cattle that causes the disease, anaplasmosis. In the present study, a total of 11 Anaplasma marginale seronegative calves were assigned into two groups: one immunized (G1, n = 6) and one nonimmunized-control (G2, n = 5). Six calves were immunized by using a DNA vaccine containing the gene of a major surface protein, MSP1b, encoded by the plasmid identified as pcDNA3.1/MSPIb. Calves received three intramuscular inoculations of 100 mug of pcDNA3.1/MSP1b at a 20-day interval. The control group received buffer phosphate at the same schedule as the experimental group. The immune response elicited by immunization with pcDNA3.1/MSP1b was evaluated in mice and calves. Twenty days following initial immunization, specific serum antibody from four BALB/c mice bound MSP1b in inummoblots. Sixty days after the last immunization, all calves were challenged with cryopreserved A. marginale at a dose of 10(4) parasites/mL/animal by intravenous injection. Results of packed cell volume (PCV) and detection of infected erythrocytes in all experimental groups revealed that the decrease of PCV and detection of infected erythrocytes occurred at 28 to 42 days after challenge. Mean temperature values did not increase over 39.85degreesC. Antibodies developed by immunized bovines from G2 were detected 14 days after challenge. MSP1b was characterized during the immunization period and MSP2 was the most predominant polypeptide at the challenge period. DNA of A. marginale was detected in all groups just after challenge by nested PCR assay. It can be concluded that all immunized bovines were partially protected against homologous challenge.

Improvement of the ferroelectric properties of ABO(3) (A= Pb, Ca, Ba; B=Ti, Zr) films

High-quality ABO(3)/LaNiO3 (A = Ph, Ca, Ba; B = Ti, Zr) hetero structures have been grown on LaAlO3 (1 0 0) substrate by the chemical solution deposition method and crystallized by a microwave oven technique. The structural, morphological and electric properties were characterized by means of X-ray diffraction (XRD), atomic force microscope (AFM), and dielectric and ferroelectric measurements. XRD patterns revealed single-phase polycrystalline and oriented thin films whose feature depends on the composition of the films. The AFM surface morphologies showed a smooth and crack-free surface with the average grain size ranging from 116 to 300 nm for both LaNiO3 electrode and the ferroelectric films. Dielectric measurements on these samples revealed dielectric constants as high as 1800 at frequency of 100 KHz. Such results showed that the combination of the chemical solution method with the microwave process provides a promising technique to grow high-quality thin films with good dielectric and ferroelectric properties. (c) 2005 Elsevier Ltd. All rights reserved.

Antimicrobial effect of intracanal substances

In some situations, endodontic infections do not respond to therapeutic protocol. In these cases, it is suggested the administration of an alternative intracanal medication that presents a wide spectrum of action and has an in-depth effect on the root canal system. The purpose of this study was to assess the antimicrobial action of ciprofloxacin, metronidazole and polyethylene glycol and natrosol vehicles with different associations and concentrations. The minimum inhibitory concentration (MIC) was determined by using the agar dilution method. The culture media (Muller-Hinton agar) were prepared containing antimicrobial agents at multiple two-fold dilutions of 0.25 to 16 mu g/mL, and with the vehicles at the concentrations of 50, 45, 40, 35, 30 and 25%. Twenty-three microbial strains were selected for the study. Metronidazole was not capable of eliminating any of the tested microorganisms. The association of ciprofloxacin with metronidazole resulted in a reduction of the MIC. The vehicle polyethylene glycol inhibited the growth of 100% of the tested strains, while natrosol inhibited 18% of the strains. Ciprofloxacin formulations with polyethylene glycol presented better effects than those of formulations to which metronidazole was added. It was possible to conclude that ciprofloxacin presented antimicrobial action against all tested bacteria] strains, and its association with metronidazole was synergic. The vehicle polyethylene glycol showed antimicrobial effect and the ciprofloxacin/polyethylene glycol association was the most effective combination for reducing the tested bacteria and yeasts.

Natural trans-crotonin: the antiulcerogenic effect of another diterpene isolated from the bark of Croton cajucara Benth.

The nor-clerodane diterpene trans-crotonin isolated from the bark of Croton cajucara BENTH. was investigated for its ability to prevent the formation of gastric-mucosa ulceration in different experimental models in mice. The results obtained from crotonin were compared with those obtained with another diterpene, DHC (trans-dehydrocrotonin) in the same models. When previously administered (p.o.) at the dose of 100 mg/kg, crotonin, as well as DHC, significantly reduced (p<0.05) gastric injury induced by stress (72, 67%), indomethacin/bethanechol (78, 29%) and pylorus ligature (35, 30%). In the HCl/ethanol-induced gastric ulcer model, at oral doses of 100 and 250 mg/kg, crotonin significantly prevented (p<0.05) the formation of gastric lesions by 51 and 56%, respectively, when compared to the control group. Gastric injury was also of significantly less magnitude in the DHC treatment group (p<0.05). In the pylorus-ligature model, crotonin (p.o.), like cimetidine, increased the volume of gastric juice when compared to the control group (p<0.05). No significant modifications where found in gastric parameters such as pH or total acid content after oral crotonin treatment. However, systemic alterations were observed when crotonin (100 mg/kg) was previously administered intraduodenally to mice. We observed significant changes (p<0.001) in gastric-juice parameters such as an increase in volume and a decrease in gastric acidity. Those pre-treated with crotonin as well as with DHC did not increase free mucus production (p>0.05). The results suggest that crotonin presents a significant anti-ulcer effect when assessed in these ulcer-induced models. As with DHC, the antiulcerogenic effects of crotonin are probably related to anti-secretory or/and gastroprotective properties of this substance. In light of results obtained with DHC and natural trans-crotonin in the present study, we concluded that the A-ring of both diterpenes is not directly involved in the antiulcerogenic activity.

Growth and characterization of BaBi2Nb2O9 thin films made by RF-magnetron sputtering

The RF-magnetron sputtering technique has been used to deposit polycrystalline thin films of layered-structured ferroelectric BaBi2Nb2O9 (BBN). The XRD patterns for the films annealed at 700degreesC for 1 hour show the presence of the BBN phase as well as the BaNb2O6 secondary phase. A better crystallization of the BBN phase and an inhibition of the secondary phase is obtained with the increase of temperature. The surface of the prepared films was rather dense and smooth with no cracks. The 300 nm thick BBN thin films exhibited a room-temperature dielectric constant of about 779 with a dissipation factor of 0.09 at a frequency of 100 kHz.

Effect of oxygen atmosphere on the morphology of LiTaO3 thin films prepared from polymeric precursor method

Lithium tantalate (LiTaO3) thin films with (50:50) stoichiometry were prepared using polymeric organic solution. The 5-layered films were deposited on silicon (100) substrates by spin coating method. The coated substrates were thermally treated at 500degreesC for 3 h under several oxygen atmospheres in order to study the influence of oxygen flow on the crystallinity, microstructure, grain size and roughness of the final film. X-ray diffraction results showed that an oxygen flow of 100 cm(3)/min leads to LiTaO3 thin films with higher crystallinity, without preferential orientation. It was observed by scanning electron microscopy (SEM) that the thickness of thin films decreases when the oxygen flow increases. The atomic force microscopy (AFM) studies showed that the grain size and roughness are strongly influenced by oxygen flow.

Synthesis and electrical characterization of CaBi2Nb2O9 thin films deposited on Pt/Ti/SiO2/Si substrates by polymeric precursor method

We report the successful deposition of CaBi2Nb2O9 (CBN) thin films on platinum coated silicon substrates by polymeric precursor method. The CBN thin films exhibited good structural, dielectric and CBN/Pt interface characteristics. The leakage current of the capacitor structure was around 0.15 A cm(-2) at an applied electric field of 30 kV cm(-1). The capacitance-voltage measurements indicated good ferroelectric polarization switching characteristics. The typical measured small signal dielectric constant and the dissipation factor at a frequency of 100 kHz were 90 and 0.053, respectively. The remanent polarization and the drive voltage values were 4.2 C cm(-2) and 1.7 V at an applied voltage of 10 V. No significant fatigue was observed at least up to 10(8) switching cycles. (c) 2005 Elsevier B.V. All rights reserved.

Low temperature synthesis and electrical properties of PbTiO3 thin films prepared by the polymeric precursor method

Ferroelectric PbTiO3 thin films were successfully prepared on a Pt(111)Ti/SiO2/Si(100) substrate for the first time by spin coating, using the polymeric precursor method. X-ray diffraction patterns of the films indicate that they are polycrystalline in nature. This method allows low temperature (500 degrees C) synthesis and high electrical properties. The multilayer PbTiO3 thin films were granular in structure with a grain size of approximately 110-120 nm. A 380-nm-thick film was obtained by carrying out four cycles of the spin-coating/heating process. Scanning electron microscopy (SEM) and atomic force microscopy (AFM) analyses showed the surface of these thin films to be smooth, dense and crack-free with low surface roughness (=3.4 nm). At room temperature and at a frequency of 100 kHz, the dielectric constant and the dissipation factor were, respectively, 570 and 0.016. The C-V characteristics of perovskite thin film prepared at low temperature show normal ferrolectric behavior. The remanent polarization and coercive field for the films deposited were 13.62 mu C/cm(2) and 121.43 kV/cm, respectively. The high electrical property values are attributed to the excellent microstrutural quality and chemical homogeneity of thin films obtained by the polymeric precursor method. (C) 2000 Elsevier B.V. S.A. All rights reserved.

Ontogenic development of Guazuma ulmifolia (Sterculiaceae) sapplings

Guazuma ulmifolia is as popular reforestation tree all over Latin America. It is characteristic of the initial stages of the secondary sucession and presents potential utility in the restoring of degraded areas. There is no information about fruit,seed and seedling morphology, which is of fundamental importance for identification, extraction, management and seed germination as well as for the characterization of post-seminal development and normal seedling pattern. To obtain such information, external fruit, and external and internal seed structures were studied considering shape, size, micropile and embryo localization; and tegumentar structures. All stages of this work were conduced in the Universidade Estadual Paulista (UNESP), Campus of Jaboticabal city. The fruits were collected in a mixed plantation in Jaboticabal city, State of São Paulo, Brazil. For the bio metric study eight repetitions of ten fruits and eight repetitions of 100 seeds were utilized. For seed internal traits study, 50 seeds were drenched in a distiled water, cut, and observed with a scanning electron microscope and a stereomicroscope, For post-seminal study ten repetitions of seven seeds were scarificated chemically with sulphuric acid during 50 min, and placed to germinate ina culture medium, at 30 degrees C, and eight hours of photoperiod. We found elipsoid, woody, indehiscent, pentacarpelar fruits, with a mean lenght of 22.61 mm (diameter 24.88 mm) and 64.0 seeds per fruit. Seed shape varies, mean length is 3.07 mm (width of 2.36 mm). The seed is bitegumented, tegmic, with a continuous, axial and curved embryo. The germination is epigeal and the seedlings are fanerocotiledoneus. Drawings of all stages are included.

Preparation, microstructural and electrical characterization of SrTiO3 thin films prepared by chemical route

Polycrystalline SrTiO3 thin films having a cubic perovskite structure were prepared at different temperatures by the polymeric precursor method on platinum-coated silicon substrate. Crystalline films with uniform composition and thickness were prepared by spin-coating and the post-deposition heat treatment was carried out at different temperatures. The film showed good structural, dielectric, and insulating properties, Scanning electron microscopy (SEM) micrographs showed no occurrence of interdiffusion between the bottom electrode (platinum) and the film during post-annealing, indicating a stable interface between the SrTiO3 and the bottom electrode. The dielectric constant and dissipation factor at a frequency of 100 kHz were 250 and 0.01, respectively, for a 360 nm thick film annealed at 600 degreesC. The capacitance versus applied voltage characteristics showed that the capacitance was almost independent of the applied voltage. The I-V characteristics were ohmic in low fields and a Schottky emission and/or Poole-Frenkel emission were postulated in high fields. Room temperature leakage current density was found to be in the order of 10(-7) A/cm(2) for a 360 nm thick film in an applied electric field of about 100 kV/cm. The charge storage density of 36 fC/mum(2) was obtained in an applied electric field of about 100 kV/cm. (C) 2001 Published by Elsevier B.V. Ltd. All rights reserved.

Screening Brazilian C gasoline quality: Application of the SIMCA chemometric method to gas chromatographic data

A total of 2400 samples of commercial Brazilian C gasoline were collected over a 6-month period from different gas stations in the São Paulo state, Brazil, and analysed with respect to 12 physicochemical parameters according to regulation 309 of the Brazilian Government Petroleum, Natural Gas and Biofuels Agency (ANP). The percentages (v/v) of hydrocarbons (olefins, aromatics and saturated) were also determined. Hierarchical cluster analysis (HCA) was employed to select 150 representative samples that exhibited least similarity on the basis of their physicochemical parameters and hydrocarbon compositions. The chromatographic profiles of the selected samples were measured by gas chromatography with flame ionisation detection and analysed using soft independent modelling of class analogy (SIMCA) method in order to create a classification scheme to identify conform gasolines according to ANP 309 regulation. Following the optimisation of the SIMCA algorithm, it was possible to classify correctly 96% of the commercial gasoline samples present in the training set of 100. In order to check the quality of the model, an external group of 50 gasoline samples (the prediction set) were analysed and the developed SIMCA model classified 94% of these correctly. The developed chemometric method is recommended for screening commercial gasoline quality and detection of potential adulteration. (c) 2007 Elsevier B.V. All rights reserved.

EFFECTS OF 2,4-DICHLOROPHENOXYACETIC ACID (2,4-D) ON OPEN-FIELD BEHAVIOR AND NEUROCHEMICAL PARAMETERS OF RATS

The effects of the herbicide 2,4-dichlorophenoxyacetic acid (2,4-D) on the central nervous system (CNS) were studied in rats. Behavioural and neurochemical studies were performed. Results show that acute and oral administration of dimethylamine 2,4-D was able to decrease locomotion and rearing frequencies and to increase immobility duration of rats observed in an open-field test. Treatment of rats with p-chlorophenylalanine (PCPA) was unable to change rat's open-field behaviour; 5-hydroxytryptophan (5-HTP) administration not only increased locomotion and rearing frequences but also decreased immobility duration. Pretreatment of the rats with PCPA and 5-HTP decreased and increased dimethylamine 2,4-D effects, respectively. The herbicide was not able to change the striatal levels of dopamine and homovanilic acid but decreased the striatal levels of serotonin (5-HT), as observed for the doses of 100 and 200 mg/kg and increased those of 5-hydroxyindoleacetic acid (5-HIAA) as measured after the 200 mg/kg dose treatment. When the levels of serotonin and 5-HIAA were measured at the brain stem level, only those of 5-HIAA were modified, being increased by diethylamine 2,4-D (60; 100 and 200 mg/kg); this increment on 5-HIAA levels was observed even 1 hr after pesticide administration. Further analysis showed that 2,4-D concentrations chromatographycally detected both in serum and brain of the intoxicated animals were dose-dependent, being found as early as 1 hr after the smaller dose of the herbicide used (10 mg/kg). The results suggest that diethylamine 2,4-D modify 5-HT functional activity within the CNS. Thus, the effects of the herbicide on open-field behaviour of rats could be attributed to a direct or indirect pesticide action on serotoninergic systems.

Short-term temporal changes in the spatial variability model of CO2 emissions from a Brazilian bare soil

In this work, the spatial variability model of CO2 emissions and soil properties of a Brazilian bare soil were investigated. Carbon dioxide emissions were measured on three different days at contrasted soil temperature and soil moisture conditions, and soil properties were investigated at the same points where emissions were measured. One spatial variability model of soil CO2 emissions was found for each measurement day, and these models are similar to the ones of soil properties studied in an area of 100 x 100 m. (C) 2000 Elsevier B.V. Ltd. All rights reserved.

Dielectric and fatigue properties of Pb(Zr0.53Ti0.47)O-3 thin films prepared from oxide precursors method

Fatigue is an important problem to be considered if a ferroelectric film is used for non-volatile memory devices. In this phenomena, the remanent polarization and coercive field properties degrades in cycles which increase in hysteresis loops. The reasons have been attributed to different mechanisms such as a large voltage applied on ferroelectric film in every reading process in Ferroelectric Random Access Memory (FeRAM) or memories for digital storage in computer, grain size effects and others. The aim of this work is to investigate the influence of the crystallization kinetics on dielectric and ferroelectric properties of the Pb(Zr0.53Ti0.47)O-3 thin films prepared by an alternative chemical method. Films were crystallized in air on Pt/Ti/SiO2/Si substrates at 700 degrees C for 1 hour, in conventional thermal annealing (CTA), and at 700 degrees C for 1 min and 700 degrees C 5 min, using a rapid thermal annealing (RTA) process. Final films were crack free and presented an average of 750 nm in thickness. Dielectric properties were studied in the frequency range of 100 Hz - 1 MHz. All films showed a dielectric dispersion at low frequency. Ferroelectric properties were measured from hysteresis loops at 10 kHz. The obtained remanent polarization (P-r) and coercive field (E-c) were 3.7 mu C/cm(2) and 71.9 kV/cm respectively for film crystallized by CTA while in films crystallized by RTA these parameters were essentially the same. In the fatigue process, the P, value decreased to 14% from the initial value after 1.3 x 10(9) switching cycles, for film by CTA, while for film crystallized by RTA for 5 min, P, decreased to 47% from initial value after 1.7 x 10(9) switching cycles.