Análise dos efeitos das deformações estruturais sobre a transferência transversal de carga em um veículo do tipo fórmula SAE submetido a uma aceleração lateral constante

This paper studies the frame deformations on a formula SAE vehicle in steady-state cornering and its influence on the lateral load transfers and, consequently, on the tires normal loads due to the applied lateral load. For a vehicle with a perfect rigid frame, the vehicle mass, the position of the center of gravity and the suspensions are the only factors responsible for the load distribution between the tires. When the frame deformations are no longer negligible, the frame deformations affect the loaddistribution between the tires. The frame flexibility turns it able to behave as an additional set of springs to the suspension system, thus changing the behavior of the set. This paper describes howit happens and suggests ways to minimize this phenomenon

Estudo, desenvolvimento e concepção de uma célula de carga

In engineering projects, it’s fundamental to determine the active loads in components in order to guarantee acceptable values of safety and reliability according to project specifications. On the other hand, force measurement methods might be very complex and impracticable in some cases and, so that, load cells with eletric resistance strain gages can be applied as a simple and accurate option to measure the required load. The main purpose of this paper is to present the development of a load cell that measures uniaxial forces using electric resistance strain gages without being influenced by the location of the loading in a cantilever beam. For that, it was taken as basis a secondary purpose which is to present a general study of basic and wide concepts about transducers, load cells and extensometers primarily. Information such as: loading and measurements types, characteristics of the presented devices as well as factors that influence its functioning, the most common kinds of Wheatstone bridge links, the main points of a load cell project, cements used to fix extensometers and, finally, the project itself with the tests of the built transducer are presented. By the end of this paper, all the results are shown and analyzed, concluding about the designed load cell and the work itself

Avaliação da influência do formato da porca e da pré-carga em juntas aparafusadas em tração

Many structures and mechanical equipment requires a union member, and the screw is one of the most used, the cost is low, it is versatile and easy to find on the market. The resulting pre-load assembly torque associated with the cyclical external load has great influence, so it will be studied carefully. This study analyzed some of these factors, as the format of nuts, and the washer material when they are incompatible with the bolt material can cause a reduction in life of the joint fatigue

Sistema de gerenciamento de energia para controle de carga/descarga entre baterias de lítio e ultracapacitores, envolvendo sistema de tração elétrica com frenagem regenerativa

Pós-graduação em Engenharia Elétrica - FEIS

Efeito de protocolos de cimentação na carga de fratura para uma cerâmica de dissilicato de lítio

Pós-graduação em Odontologia Restauradora - ICT

Flora intermediária em mulheres em idade reprodutiva: aspectos inflamatórios, atividade de sialidases e carga bacteriana

Pós-graduação em Patologia - FMB

Determinação do tempo de vida de restaurações totalmente cerâmicas (y-tzp/porcelana) com incidência da carga em diferentes regiões de contato

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Nova configuração de um reator compartimentado anaeróbio/aeróbio para o tratamento de esgoto sanitário de baixa carga

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Relação entre carga parasitária de cães naturalmente acometidos por leishmaniose visceral e infectividade para Lutzomyia longipalpis: Lilian Aparecida Colebrusco Rodas. -

Pós-graduação em Ciência Animal - FMVA

Frequência de ressonância e sondagem peri-implantar em implantes curtos sob carga imediata com prótese total fixa em cantiléver na arcada mandibular: acompanhamento de um ano

This paper presents a case report with the use of short dental implants and immediate prosthesis placement. After 13 months of follow-up, peri-implant probing values are near 1.87 mm and ISQ values around 78.56.

Rehabilitacion oral sobre implantes instalados por medio de la tecnica sin colgajo (flapless) y carga inmediata

The oral rehabilitation with osseointegrated implants is a well-documented treatment with high rate of success. Nevertheless, demands related to treatment time and surgical technique began to appear. In this context, the procedure of immediate loading in which the dental prosthesis is placed right after implant surgery has become a constant practice. Although immediate loading has been an important advance, minimally invasive procedures, such as implant placement without raising a mucoperiosteal flap (flapless) are increasingly being performed. Association of immediate loading with the flapless technique improves acceptance by patients and professionals, because no suturing is required. Moreover, it reduces swelling, bleeding during and after surgery, postoperative pain, surgery time, discomfort and hematoma, as well as the need for postoperative medication. These characteristics ease the stages of rehabilitation soon after implant placement, cooperating with prosthodontist's work. Thus, the proposal of this study is to present a clinical case of oral rehabilitation with osseointegrated implants and fixed prosthesis in both arches, in which the flapless technique was applied, followed by immediate loading. It will discuss the diagnosis, prosthetic planning, surgical/prosthodontic procedures and follow-up for 20 months.

Influência do desenho do implante na micromovimentação de implantes imediatos com carga imediata: análise multivariada em elementos finitos

The purpose of this paper was to evaluate the influence of different implant designs on the micromovements of immediately placed implants. CT-based finite element models comprising an upper central incisor socket and four commercially available internal connection implant designs (SIN SW®, 3i Certain®, Nobel ReplaceTM, and RN synOcta® ITI Standard) of comparable diameter and length were constructed. 50, 100 and 200N magnitude loads were applied over the implant. ANOVA at 95% level of significance was used to evaluate bone to implant relative displacement (micromovements). The implant design (68,80%) greatly influences the micromovement of immediately placed implants. However, the loading magnitude (68,80%) is the most important factor regarding the implant stability in this protocol.

Carga imediata em implantes unitários: revisão da literatura

The possibilities of treatment with dental implants have revolutionized the field of oral rehabilitation in recent years, bringing a number of advantages over conventional prostheses. For years, a surgical protocol was followed that called for maintaining the implant without load for a certain period for osseointegration, but experimental studies have shown that immediate loading of implants also leads to the formation of peri-implant bone tissue along the time, similarly to that observed for conventionally loaded implants. This study aimed to conduct a literature review regarding the use of this alternative rehabilitation with single implants. The immediate loading of single-tooth replacements is presented as an excellent treatment alternative.

Eventos adversos relacionados à gravidade e carga de trabalho de enfermagem em Unidade de Terapia Intensiva

Pós-graduação em Enfermagem - FMB

Comparação entre a variação da pressão de pulso e o índice de variabilidade pletismográfica como índices dinâmicos de pré-carga em cães anestesiados com isoflurano submetidos à hemorragia hipotensiva por reposição volêmica

Pós-graduação em Anestesiologia - FMB