Perdas de solo e deposição de sedimentos em duas subbacias hidrográficas no entorno da usina hidrelétrica de Ilha Solteira-SP

Pós-graduação em Agronomia (Irrigação e Drenagem) - FCA

Avaliação de parâmetros da tecnologia de aplicação para o controle da ferrugem asiática da soja

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Deposição e lixiviação do herbicida tebuthiuron em palha de cana-de-açúcar (cana-crua)

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Influência da deposição de filmes de carbono tipo diamante na infiltração bacteriana pela interface entre implantes e pilares protéticos

Pós-graduação em Odontologia Restauradora - ICT

Eficiência de volumes e pontas de pulverização centrífuga e hidráulica na distribuição e deposição da calda no controle da ferrugem asiática da soja

Pós-graduação em Agronomia (Produção Vegetal) - FCAV

Otimização do processo de deposição de filmes TiO2:Mn usando RF magnetron sputtering

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Desenvolvimento e otimização de materiais nanocristalinos para células solares sensibilizadas

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Deposição de nutrientes na carcaça de girinos de rã-touro

The objective of this work was to determine nutrient deposition on the carcass of bullfrog (Lithobates catesbeianus) tadpoles using a nonlinear model. A total of 2,700 tadpoles with an average weight of 0.039 g were used. Commercial ground feed containing 55% crude protein was offered ad libitum. The animals were weighed and evaluated every ten days for analysis of crude protein, ether extract, water, and mineral salt contents. The parameters of the Gompertz model were estimated by the modified Gauss-Newton method, and the deposition rates (g per day) over time were calculated by the resulting equation. The values found for the parameters of the Gompertz equation, used to describe nutrient deposition on tadpole carcass, showed biological interpretation. Maximum deposition rate (t*) was observed on the 36.2331th day for protein, on the 37.1420th day for water, on the 35.2971th day for mineral salt, and on the 41.3547th day for fat. Nutrient intake from the diet is higher than the deposition rate on the tadpole carcass.

Descrição do potencial de retenção de nitrogênio em frangas de postura por diferentes metodologias: máxima deposição e estimativas da ingestão de metionina+cistina

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Taxa de deposição de tecidos corporais de novilhas Nelore e suas cruzas com Angus e Simental

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Padrão de deposição de tecidos muscular e adiposo de bovinos Nelore castrados e não- castrados suplementados com cloridrato e zilpaterol

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Deposição e caracterização de filmes de óxido de cobalto por sputtering reativo

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Comparação da razão sinal-ruído e da uniformidade da imagem entre aquisições com bobina de quadratura e com bobina de corpo

The signal-to-noise ratio and image uniformity analysis parameters are very important in quality control of an MRI scanner. They are measured in regular tests with phantoms. In these tests, however, used to quadrature coil, which has been most widely used clinically, and, therefore, was replaced in the procedures for body coil. In order to understand the difference between these two parameters in these coils, the study aimed to analyze the images acquired from four different phantoms in the same equipment under the same conditions for comparison purposes. With these results, it can be concluded that the body coil signal-to-noise ratio has always smaller than the quadrature in any projection, whereas the image uniformity is larger

Implantação iônica por imersão em plasma e deposição de filmes finos poliméricos provenientes da mistura hexametildisilazano/argônio

Thin polymeric films deposited by plasma are very atractive for many industrial and scientific applications, in areas such as electronics, mechanics, coatings, biomaterials, among others, due to its favorable properties such as good adhesion to the substrate, high crosslinking, nanomectric thickness, homogeneity, etc. In this work, thin films were deposited by plasma immersion ion implantation and deposition technique from a hexamethyldisilazane/argon mixture at different proportions. These films were subjected to several characterizations, such as, contact angle, which presented values near to 100 degrees, surface energy, with values near to 31 mJ/m2, hardness with values between 0.7 and 2.6 GPa, thickness from 100 to 200 nm, refractive index from 1.56 to 1.64, molecular structure presenting the following functional groups in the infrared spectra region: CHx from 2960 to 2900 cm-1; Si-H around 2130 cm-1; CH3 in Si-(CH3)x around 1410 cm-1; CH3 in Si-(CH3)x in 1260 cm-1; N-H around 1180 cm-1; CH2 in Si-CH2-Si bonds around 1025 cm-1; Si-O in Si-O-Si from 1020 to 1100 cm-1; Si-N in Si-H-Si bonds around 940 cm-1; CH3 in Si-(CH3)3 in 850 cm-1; Si-C bonds in Si-(CH3)2 around 800 cm-1; and Si-H in 680 cm-1 . From these characterizations, it was possible to conclude that the concentration of argon or hexamethyldisilazane in the mixture changed the resulting polymer

Análise da deposição de filmes finos semicondutores de GaN e GaN e Ga1-xMnxN preparados por sputtering reativo

Thin films of Ga1-xMnxN have great interest in its potential for control of electron spin (spintronics), in most cases this material is synthesized by techniques that have a high degree of control the deposition parameters, such as molecular beam epitaxy (MBE) and deposition of metalorganic chemical vapor deposition (MOCVD). The sputtering technique is an alternative route to produce such materials. Here we study the film deposition Ga1-xMnxN by reactive sputtering technique and apply enhancements such as a glove box, a residual gas analyzer and temperature control system, in order to growth films epitaxially using an analysis of the preconditions of films analyzed by spectroscopic techniques and microscopic. These procedures helped to improve the technique of deposition by cleaning substrates in an inert environment, and by the analysis of trace gases and heating the substrate holder as explained in the literature. Through the applications and comparisons it can be pointed out that the technique has the advantage of its simplicity and relatively low cost compared to MBE and MOCVD, but produces polycrystalline material