Retificador entrelaçado com elevado fator de potência para operação de um veículo trólebus alimentado por redes em CA Ou CC

This paper presents the development and the main results for an interleaved boost rectifier operating as a special input power stage for a trolleybus type vehicle, allowing its feeding by alternate current (AC) or direct current (DC) distribution power systems. When feeding with two wires (single phase) alternate current distribution system, the converter accomplish active power factor correction, providing a relatively sinusoidal current with low total harmonic distortion (THD) and fully complying with IEC 61000-3-4 standards. In addition, a management control system promotes the required automatic operation changes for the proposed rectifier when the vehicle is changing from the DC distribution power system to the AC distribution power system and vice-versa, keeping its original electrical DC system characteristics for the adjustable speed driver sub-system. The main experimental results for a prototype rated at 150kW are presented, considering its application for a trolleybus with DC adjustable speed driver, demonstrating the proposed converter benefits and the possibility of AC feeding system for trolleybus type vehicle.

Oportunidades de melhoria na gestão de resíduos em empresas distribuidoras de eletricidade: o caso da AES Eletropaulo

A gestão de resíduos em distribuidoras de eletricidade é bastante complexa, pois enquadram-se em vários tipos (valorizados ou não) e gerados em grande quantidade. Em 2009, a AES Eletropaulo gerou quase quatro mil toneladas de resíduos não perigosos, subdivididos em 30 tipos. Uma divisão por materiais, após desmontagem e separação dos diferentes materiais contidos nos fios, cabos, chaves, isoladores com ferragem e para-raios, subiria o valor da venda em R$ 600 mil. Isso geraria cerca de 214 toneladas de porcelana que, moídas, poderiam substituir as 210 toneladas de brita compradas anualmente pela concessionária para uso em subestações. Cerca de 160 toneladas de porcelanas intactas poderiam ser utilizadas na confecção de gabiões para contenção de encostas. Além disso, peças de ferro galvanizado poderiam ser decapadas e novamente galvanizadas para reaproveitamento.

Construção e validação de um túnel de vento para ensaios de estimativa da deriva em pulverizações agrícolas

The aim of this study was to build and validate a low cost reduced-scale wind tunnel for drift evaluation on pesticide application technology. The work was carried out at the NEMPA - Núcleo de Ensaio de Máquinas e Pneus Agroflorestais (NEMPA), FCA/UNESP, Departamento de Engenharia Rural, Botucatu/SP, Brazil. The wind tunnel main characteristics were an open circuit and a closed working section with a fan blowing air into the tunnel. Screens were fitted downstream after the fan in order to stabilize the air flow on the working section. The tunnel was built with 3.0 mm eucalyptus hardboard, with a total length of 4.8 m and a squared section of 0.56 m. The air flow was provided by a 180 W axial fan. The system was adjusted and calibrated to provide a laminar and stable flow at 2.0 m s-1. Validation studies were carried out by using a Teejet XR 8003 flat fan nozzle at 200 kPa (medium droplets) to apply a spray solutions containing water plus a food dye (Blue FDC) at 0,6% m v-1 mixed with two adjuvants: a polymer based anti drift formulation at 0,06% m v-1 and a sodium lauryl ether sulfate based surfactant at 0,2% v v-1. After a 10-second application the drift was collected on nylon strips transversally fixed along the tunnel at different distances from the nozzle and different high from the bottom part of the tunnel. Drift deposits were evaluated by spectrophotometry. The wind tunnel had low levels of turbulence and high repeatability of the data, which means that the flow was uniform and able to be used for carrying out measures to estimate drift. The validation results showed that the tunnel was effective to enable comparative drift measurements on the spray solution used in this work making possible the evaluation of drift risk potential under those spray technologies. The use of an adjuvant based on a polymer reduced the amount of drift from the nozzle compared to the surfactant.

Caracterização física e química e potencial de deriva de caldas contendo surfatantes em pulverizações agrícolas

The aim of this work was to evaluate the effect of the addition of different surfactants in physical and chemical properties of spray solutions, droplets spectra and drift potential on agricultural spraying. The surfactants and concentrations (v v-1) were: Haiten (0.1%), Antideriva and Intec (0.05% and 0.1%). The following characteristics were analyzed: surface tension, viscosity, density and electric conductivity. The droplet size spectrum was determined by a laser particle analyzer (Mastersizer S®, version 2.15) including measurements of volume medium diameter (VMD), the percent of droplets below 50 and 100 μm (V50 e V100) and index span. In order to estimate the drift potential, a series of wind tunnel tests were performed with a Teejet XR 8003 flat fan nozzle at 200 kPa (medium droplets) used to apply the spray solutions containing water, the adjuvants and a food color dye (Brilliant blue FD & C no 1) at 0,6% m v-1. The drift was collected on nylon strips transversally fixed along the tunnel at different distances from the nozzle and different high from the bottom part of the tunnel. Drift deposits were evaluated by spectrophotometry. The results showed that the addition of adjuvants changed physical and chemical properties of spray solutions in different magnitudes according to the surfactant. Surfactants changed the droplet spectrum and drift potential, indicating that higher VMD and smaller V100 induced higher percentage of drift.

Monitoramento do tempo de prensagem e do comportamento da temperatura através da espessura de painéis LVL (Laminated veneer lumber)

The aim of this study was to analyze the behavior of the flow of heat (temperature) through the thickness of panels LVL (Laminated veneer lumber) produced with phenol formaldehyde adhesive, in laboratorial and industrial scales. Experimental program was conducted with five LVL panels (three produced in laboratorial scale and two in industrial scale) with different arrangements of a mix of commercial veneers from tropical pinus from the south region of Sao Paulo State, Brazil, bonded using phenol formaldehyde adhesive. The temperature inside the panels during the pressing process was evaluated using thermocouples type T (cooper-constantan), installed mostly in the center of the glue lines and connected to a data acquisition system. The graphics of temperature as a function of the time showed a gradual increase of temperature up to pre-set values, remaining constant from them. The temperature reached at the center of the panels was adequate to promote the curing of the adhesive. These pre-set values were similar to the minimum values presented by other authors and manufacturers of these adhesives that affirm that temperatures above 100ºC at the center of laminated panels bonded with phenolic adhesives are sufficient to ensure proper cure of the resin. The time necessary for curing of the adhesives confirmed the validity of practical expressions provided by adhesive manufacturers.

Os caminhos movediços de Bandeira

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Membranas de biocelulose como substrato para o crescimento de nanofios de ZnO: síntese e aplicação

Pós-graduação em Química - IQ

Relação entre a composição de condicionadores capilares e a formação de cristais líquidos

O Brasil é o terceiro maior consumidor de cosméticos no mundo, representando a segunda colocação em produtos de higiene capilar. Tal colocação está relacionada aos nossos padrões de cuidados estéticos capilares, que muitas vezes, provocam agressões físicas e químicas, deixando os cabelos danificados e quebradiços. Os condicionadores capilares tornam-se uma ferramenta interessante, devido aos inúmeros benefícios protetores oferecidos às superfícies dos fios. A presença de tensoativos catiônicos e álcoois graxos de cadeia longa, unidos à temperatura de fusão dos materiais, velocidade de agitação imposta e resfriamento adequado do produto, podem ser os responsáveis pela formação de cristais líquidos. Tais estruturas conferem estabilidade, viscosidade, melhorias na aparência estética e sensorial do produto e, devido a estas qualidades estão ganhando espaço no mercado cosmético. Assim, o objetivo do trabalho foi desenvolver e formular condicionadores capilares variando-se as concentrações e/ou os tensoativos catiônicos e álcoois graxos, visando obter estruturas líquido-cristalinas associadas aos condicionadores, através da técnica de microscopia de luz polarizada (MLP), caracterização das estruturas pela técnica de espalhamento de raios-X a baixo ângulo (SAXS) e analise do perfil de textura (TPA) das formulações. Foram manipuladas 14 emulsões O/A, variando-se os álcoois graxos de cadeia longa (16 a 18C) e ceras auto emulsionantes catiônicas. Os resultados da MLP foram, em sua maioria, positivos para a presença de estruturas na forma de cruz de malta. A técnica de SAXS confirmou os sistemas sugeridos pela MLP caracterizando a estrutura líquida cristalina do tipo lamelar. A TPA inferiu que a alta estabilidade física apresentada por estas emulsões, e seu particular desempenho no deslizamento dos cabelos, pode estar relacionada à presença de tal organização estrutural nas formulações...

Análise organizacional de acidentes de trabalho no setor de distribuição de energia elétrica

Pós-graduação em Saúde Coletiva - FMB