Influence of the grinding wheel's dive speed on the damage of rectified hardened steels

The world tendency is the increase of the productivity and the production of pieces more and more sophisticated, with high degree of geometric and dimensional tolerances, with good surface finish and low cost. Rectification is responsible for the final finish in the machining process of a material. However, damages generated in this production phase affect all the resources used in the previous processes. Great part of the problems happennig in the rectification process is due to the enormous temperature generated in this activity because of the machining conditions. The dive speed, which is directly related to the productivity, is considered responsible for the damages that occur during rectification, limiting its values to those that do not cause such damages. In this work, through the variation of the dive speed in the process of cylindrical grinding of type ABNT D6 steel, rationalizing the application of two cutting fluids and using a CBN (cubic boron nitrate) abrasive wheel with vitrified blond, the influence of the dive speed on the surface damages of hardened steels was evaluated. The results allowed to say that the dive speed, associated to an efficient cooling and lubrication, didn't provoke thermal damages (including heated zones, cracks and tension stresses) to the material. Residual stresses and the roughness of rectified materials presented a correlation with the machining conditions. The work concluded that it is possible to increase the productivity without provoking damages in the rectified components.

Evaluation of the effect of the stoichiometric ratio of Ca/Cu on the electrical and microstructural properties of the CaCu3Ti4O12 polycrystalline system

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

On the Phase Transformation in Mechanically Alloyed Ni-Nb and Ni-Ta and Ni-Nb-Ta Powders

This paper reports on the phase transformation during the preparation of Ni-25Nb, Ni-25Ta, Ni-20Nb-5Ta and Ni-15Nb-10Ta (at-%) powders by high-energy ball milling from elemental powders. The milling process was performed in a planetary ball milling using stainless steel balls and vials, rotary speed of 300rpm, and a ball-to-powder of 10:1. To minimize contamination and spontaneous ignition the powders were handled under argon atmosphere in a glove box. The milled powders were characterized by means of X-ray diffraction techniques. Results indicated that the Ni atoms were preferentially dissolved into the Nb (and/or Ta) lattice at the initial milling times, which contributed to change the relative intensity on the diffraction peaks. After the dissolution of Nb (and/or Ta) into the Ni lattice, the Ni peaks were moved to the direction of lower diffraction angles in Ni-25Nb, Ni-25Ta, Ni-20Nb-5Ta, Ni-15Nb-10Ta powders, indicating that the mechanical alloying was achieved.

A Comparison of the Effects of Nonlinear Damping on the Free Vibration of a Single-Degree-of-Freedom System

This article concerns the free vibration of a single-degree-of-freedom (SDOF) system with three types of nonlinear damping. One system considered is where the spring and the damper are connected to the mass so that they are orthogonal, and the vibration is in the direction of the spring. It is shown that, provided the displacement is small, this system behaves in a similar way to the conventional SDOF system with cubic damping, in which the spring and the damper are connected so they act in the same direction. For completeness, these systems are compared with a conventional SDOF system with quadratic damping. By transforming all the equations of motion of the systems so that the damping force is proportional to the product of a displacement dependent term and velocity, then all the systems can be directly compared. It is seen that the system with cubic damping is worse than that with quadratic damping for the attenuation of free vibration. [DOI: 10.1115/1.4005010]

On the dynamic behaviour of the "click" mechanism in dipteran flight

In this paper, the dynamic behaviour of the "click" mechanism is analysed. A more accurate model is used than in the past, in which the limits of movement due to the geometry of the flight mechanism are imposed. Moreover, the effects of different damping models are investigated. In previous work, the damping model was assumed to be of the linear viscous type for simplicity, but it is likely that the damping due to drag forces is nonlinear. Accordingly, a model of damping in which the damping force is proportional to the square of the velocity is used, and the results are compared with the simpler model of linear viscous damping. Because of the complexity of the model an analytical approach is not possible so the problem has been cast in terms of non-dimensional variables and solved numerically. The peak kinetic energy of the wing root per energy input in one cycle is chosen to study the effectiveness of the "click" mechanism compared with a linear resonant mechanism. It is shown that, the "click" mechanism has distinct advantages when it is driven below its resonant frequency. When the damping is quadratic, there are some further advantages compared to when the damping is linear and viscous, provided that the amplitude of the excitation force is large enough to avoid the erratic behaviour of the mechanism that occurs for small forces. (C) 2011 Elsevier Ltd. All rights reserved.

Adsorption and electropolymerization of toluidine blue on the nano structured octakis(hydridodimethylsiloxy)-octasilsesquioxane surface

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Effect of the addition of soy lecithin and Yucca schidigera extract on the properties of gelatin and glycerol based biodegradable films

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Effects of a muscarinic type-2 antagonist on cardiorespiratory function and intestinal transit in horses anesthetized with halothane and xylazine

Objective-To evaluate the cardiorespiratory and intestinal effects of the muscarinic type-2 (M-2) antagonist, methoctramine, in anesthetized horses.Animals-6 horses.Procedure-Horses were allocated to 2 treatments in a randomized complete block design. Anesthesia was maintained with halothane (1% end-tidal concentration) combined with a constant-rate infusion of xylazine hydrochloride (1 mg/kg/h, IV) and mechanical ventilation. Hemodynamic variables were monitored after induction of anesthesia and for 120 minutes after administration of methoctramine or saline (0.9% NaCl) solution (control treatment). Methoctramine was given at 10-minute intervals (10 mug/kg, IV) until heart rate (HR) increased at least 30% above baseline values or until a maximum cumulative dose of 30 mug/kg had been administered. Recovery characteristics, intestinal auscultation scores, and intestinal transit determined by use of chromium oxide were assessed during the postanesthetic period.Results-Methoctramine was given at a total cumulative dose of 30 mug/kg to 4 horses, whereas 2 horses received 10 mug/kg. Administration of methoctramine resulted in increases in HR, cardiac output, arterial blood pressure, and tissue oxygen delivery. Intestinal auscultation scores and intestinal transit time (interval to first and last detection of chromium oxide in the feces) did not differ between treatment groups.Conclusions and Clinical Relevance-Methoctramine improved hemodynamic function in horses anesthetized by use of halothane and xylazine without causing a clinically detectable delay in the return to normal intestinal motility during the postanesthetic period. Because of their selective positive chronotropic effects, M-2 antagonists may represent a safe alternative for treatment of horses with intraoperative bracycardia.

The effects of atropine and methotrimeprazine on the epinephrine-induced arrhythmias in halothane-anesthetized dogs

The effects of atropine and methotrimeprazine on epinephrine-induced ventricular arrhythmias were evaluated in halothane-anesthetized dogs. Ten mixed-breed dogs were assigned to 3 treatments (saline, atropine, and methotrimeprazine) in a randomized complete block design. Anesthesia was induced and maintained with halothane (1.5 minimum alveolar concentration) in oxygen. Controlled ventilation was used throughout to maintain eucapnia. Saline, atropine (0.05 mg/kg, IV) or methotrimeprazine (0.5 mg/kg, IV) were administered and, 5 minutes later the arrhythmogenic dose of epinephrine (ADE) was measured by IV infusion of progressively increasing infusion rates of epinephrine, until the ventricular arrhythmia criterion was met (at least 4 ectopic ventricular contractions (EVCs) during a 15-second period). Data were analyzed using a student's t-test for ADE values and multivariate profile analysis for heart rate (HR), arterial blood pressure (ABP), and rate pressure product (RPP). The ADE increased in atropine- and methotrimeprazine-treated groups, whereas 1 and 4 animals from these groups did not develop any ventricular arrhythmia, respectively. Epinephrine induced multiform premature ventricular contractions (PVCs) in the atropine group, whereas ventricular escape beats were observed in the control and methotrimeprazine groups. Heart rate and RPP decreased, and ABP increased at the time of ADE observation in the control group. Epinephrine infusion in the atropine group caused marked increases in HR, ABP, and RPP, which were associated with pulsus alternans in 2 animals. It was concluded that 1) the presence of cholinergic blockade influences the type of ventricular arrhythmia induced by epinephrine; 2) increased ADE values recorded following atropine administration must be cautiously interpreted, since in this situation the PVCs were associated with signs of increased myocardial work and ventricular failure; and 3) the use of a broader arrhythmia criterion (EVCs instead of PVCs) may not allow a direct comparison between ADE values, since it includes ventricular arrhythmias mediated by different mechanisms.

Influence of fluid volume variations on the calculated value of the left ventricular mass measured by echocardiogram in patients submitted to hemodialysis

The left ventricular mass (LVM) measurement is of major importance for renal patients, as ventricular hypertrophy is an important prognostic index. The echo-cardiogram of the ventricular mass is larger before than it is after hemodialysis, which can confuse data interpretation. The aim of this work is to study the influence of alterations in fluid volume on the variations in measurements of ventricular mass observed during the course of a hemodialysis. Sixteen patients with chronic renal insufficiency in hemodialysis were evaluated at the Dialysis Unit of the University Hospital-UNESP, Botucatu, São Paulo State. The left ventricular mass was calculated from echocardiograms taken before and after hemodialysis and simultaneous ultra-filtration (12 patients: UF GROUP) and before and after hemodialysis isovolemic phase with sequential ultra-filtration (10 patients: ISO GROUP). Six of these patients were submitted to measurements of left ventricular mass before and after hemodialysis in both isovolemic and simultaneous ultra-filtration procedures. In the UF group, there was significant reduction in the following parameters before and after dialysis: diastolic diameter from 54.0 +/- 6.0 mm to 45.6 +/- 7.6 mm; left ventricular mass from 342 +/- 114 g to 265 +/- 117 g; and its respective index (IMVE) from 214 +/- 68 g/m(2) to 168 +/- 71 g/m(2). The ISO group showed no statistically significant variation. The behavior of the variables of six patients submitted to both observations confirm these results. In conclusion, the variations in echocardiogram measurements of the left ventricular mass relating to hemodialysis appear to be induced by alterations of the volemic condition.

The impact of physical exercise on the gastrointestinal tract

Purpose of reviewPhysical exercise can be both beneficial and harmful for the gastrointestinal tract in a dose-effect relationship between its intensity and health. Mild-to-moderate intensity exercises play a protective role against colon cancer, diverticular disease, cholelithiasis and constipation, whereas acute strenuous exercise may provoke heartburn, nausea, vomiting, abdominal pain, diarrhea and even gastrointestinal bleeding. This review focuses on mechanisms involved in those symptoms and their associations with type of exercises in humans.Recent findingsOne quarter to one half of elite athletes are hampered by the gastrointestinal symptoms that may deter them from participation in training and competitive events. Vigorous exercise-induced gastrointestinal symptoms are often attributed to altered motility, mechanical factor or altered neuroimmunoendocrine secretions. Training, lifestyle modifications, meal composition, adequate hydration and avoidance of excessive use of some medications are the recommendations.SummaryStrenuous exercise and dehydrated states would be the causes of gastrointestinal symptoms referred by 70% of the athletes. Gut ischemia would be the main cause of nausea, vomiting, abdominal pain and (bloody) diarrhea. The frequency is almost twice as high during running than during other endurance sports as cycling or swimming and 1.5-3.0 times higher in the elite athletes than the recreational exercisers.

Novel insights into the genomic basis of citrus canker based on the genome sequences of two strains of Xanthomonas fuscans subsp aurantifolii

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Effect of free-choice feeding on the performance and ileal digestibility of nutrients in broilers

An experiment was conducted to study ileal digestibility of nutrients and to verify the ability of broilers to select feed in order to meet their requirements for protein and energy. The treatments consisted of six diets: R+S: free-choice feeding with rice bran (energy) and soybean meal (protein); C+G: free-choice feeding with corn (energy) and corn gluten meal (protein); R+G: free-choice feeding with rice bran (energy) and corn gluten meal (protein); C+S: free-choice feeding with corn (energy) and soybean meal (protein); R+C+G+S: free-choice feeding with rice bran and corn (energy) and corn gluten meal and soybean meal (protein); and BD: basal diet represented by a complete diet composed of 63% corn and 33% soybean meal. The results indicated that the adjustment to nutritional requirements does not depend only on the ability of birds to select feed. It might also depend on intake and ingredient quality, since some ingredients did not provide a balanced amount of nutrients. The birds were able to fulfill their requirements for maintenance, that is, they consumed the minimum amount of amino acids (g per day) for maximum growth. The free-choice group with corn gluten meal as the protein source had the worst performance, which indicated that this feed is not recommended as a primary source of amino acids for broilers. The C+G diet presented the highest digestibility coefficient of dry matter and crude protein, whereas the C+S diet resulted in the highest digestibility coefficient of ether extract and nitrogen-free extract, indicating that diet digestibility was affected by the type of feed used as energy and protein sources. In general, the high digestibility values indicate that broilers are able to efficiently digest and absorb the supplied feed.

Effect of the calcium level and limestone particle size on the performance of semi-heavy layers in the second cycle of egg production

An experiment was carried out at the Research and Development Unit of Brotas aiming at evaluating dietary calcium level and limestone particle size on the production performance of commercial (Hy-Line Brown) layers in the second lay cycle. Experiment duration was 112 days. A total number of 288 hens, with 83 weeks of age in the beginning of the experiment, were used in a completely randomized experimental design in a factorial arrangement of 2x3, with two calcium levels (3.5 and 4.0%) and three limestone particle size compositions: 100% fine limestone (FL), 30% coarse limestone (CL) + 70% fine limestone (FL), and 50% (CL) + 50% (FL), with six replicates of eight birds each. Egg weight (g), egg production (%), egg mass (%), feed intake (g), feed conversion ratio (kg/dz and kg/kg), mortality (%), and egg loss (%) were evaluated. The analysis of variance did not detect significant differences (p>0.05) among treatments on any of the evaluated performance parameters. It was concluded that the tested calcium levels and limestone particle composition did not influence the performance of semi-heavy layers in second production cycle.

Forced-Molting methods and their effects on the performance and egg quality of japanese quails (Coturnix japonica) in the second laying cycle

The experiment was carried out in the experimental poultry house of the Research and Development Unit of Brotas of Agência Paulista de Tecnologia dos Agronegócios do Centro-Oeste, SP, Brazil. The objective of the study was to evaluate the performance of Japanese quails submitted to forced molting aiming at optimizing the use of the same quail flock by promoting a second laying cycle. A total number of 400 67-day-old Japanese quails in lay, previously submitted to 14 days of forced molting, was distributed in a completely randomized experimental design into five treatments (T1= not submitted to forced molting, T2= 03 days of fasting + fed ad libitum, T3= 01 days of fasting + 13 days of feed restriction, T4= 02 days of fasting + 12 days of feed restriction, and T5= 03 days of fasting + 11 days of feed restriction. Feeds were contained equal nutrient levels, and were formulated according to NRC (1994) recommendations. There were significant differences among the studied treatments. Although the treatment of 3 days of fasting followed by ad libitum feeding resulted in lower egg weight, it promoted better lay percentage, egg mass, and feed conversion ratios (FCR/dz and FCR/kg). on the other hand, 3 days of fasting followed by restricted feeding resulted in higher feed intake and worse feed conversion ratios (FCR/dz and FCR/kg). When birds were not submitted to forced molting, they presented lower lay percentage and egg mass.