Numerical and experimental analysis of natural convection in a cavity with flush mounted heat sources on a side wall

This work considers a problem of interest in several technological applications such as the thermal control of electronic equipment. It is also important to study the heat transfer performance of these components under off-normal conditions, such as during failure of cooling fans. The effect of natural convection on the flow and heat transfer in a cavity with two flush mounted heat sources on the left vertical wall, simulating electronic components, is studied numerically and experimentally. The influence of the power distribution, spacing between the heat sources and cavity aspect ratio have been investigated. An analysis of the average Nusselt number of the two heat sources was performed to investigate the behavior of the heat transfer coefficients. The results obtained numerically and experimentally, after an error analysis, showed a good agreement.

An investigation of electrolytic surface damages and electroplated crhomium effects on fatigue behavior of high strength steel

Fatigue crack initiation occurs at the surface, although sub surface nucleation has also been reported. Localized imperfections like inclusions close to surface and surface small pits can result in crack sources. Coatings are not always beneficial by fatigue point of view too. Mechanical properties of the covering material can change considerably the fatigue behavior of base metal due to residual surface stresses, to micro cracks or to hydrogen embrittlement. This paper is concerned with analysis of electrolytic etch on the fatigue resistance of a 35NCD16 high strength steel in a mechanical condition of (1760 - 1960) MPa, and analysis of electroplated hard chromium effects on the fatigue resistance in a strength condition of 989 MPa. Hardness impression was used as a reference parameter in case of electrolytic etch. In both cases, experimental data showed that fatigue strength of 35NCD16 steel was considerably reduced. Copyright © 2001 Society of Automotive Engineers, Inc.

A two phase flow nonlinear parameter estimation for capillary tube-suction line heat exchanger

Here we present two-phase flow nonlinear parameter estimation for HFC's flow through capillary tube-suction line heat exchangers, commonly used as expansion devices in small refrigeration systems. The simplifying assumptions adopted are: steady state, pure refrigerant, one-dimensional flow, negligible axial heat conduction in the fluid, capillary tube and suction line walls. Additionally, it is considered that the refrigerant is free from oil and both phases are assumed to be at the same pressure, that is, surface tension effects are neglected. Metastable flow effects are also disregarded, and the vapor is assumed to be saturated at the local pressure. The so-called homogeneous model, involving three, first order, ordinary differential equations is applied to analyze the two-phase flow region. Comparison is done with experimental measurements of the mass flow rate and temperature distribution along capillary tubes working with refrigerant HFC-134a in different operating conditions.

Dietary electrolyte balance for broiler chickens under moderately high ambient temperatures and relative humidities

Cobb male broiler chicks (1,000) on new litter were used to evaluate effects of dietary electrolyte balance [DEB; Na+K-Cl, milliequivalents (mEq) per kilogram] under tropical summer conditions. Corn-soybean meal-based mash diets had salt (NaCl) alone or in combination with one or more supplements: sodium bicarbonate (NaHCO3), ammonium chloride (NH4Cl), or potassium bicarbonate (KHCO3). A completely randomized design, with five starter and grower feed treatments (control: 145, then 130 mEq/kg; or 0, 120, 240, or 360 mEq/kg throughout) and four replicate pens (1.5 x 3.2 m) per treatment (50 chicks per pen), was used. Diets were analyzed for Na, K, and Cl for confirmation. There were no significant (P < 0.05) effects of treatments on mortality or processing parameters. Water intake increased linearly with increasing DEB, giving higher litter moistures and lower rectal temperatures. Blood HCO3 and pH increased with the highest DEB (360 mEq/kg) causing respiratory alkalosis. The DEB of 240 mEg/kg gave best weight gain and feed conversion ratio, and ideal DEB predicted by regression analyses were 186 and 197 mEq/kg from 0 to 21 d of age and 236 and 207 mEq/kg of feed from 0 to 42 d, respectively. These DEB corresponded to estimated (interpolated) values in predicted optimal 186 to 197 mEq/kg starter of Na 0.38 to 0.40% and Cl 0.405 to 0.39% (K = 0.52%), in 207 to 236 mEq/kg starter, Na 0.409 to 0.445% and Cl 0.326 to 0.372% Cl (K = 0.52%), and in grower Na 0.41 to 0.445%, Cl 0.315 to 0.267% (K = 0.47%).

Dietary electrolyte balance for broiler chickens exposed to thermoneutral or heat-stress environments

Ross male broiler chicks (n = 480) on new litter were used in a randomized block design with two blocks (environmental rooms) and four treatments having four replicate pens (1.0 × 2.5 m; 15 chicks) each to evaluate dietary electrolyte balance (DEB; P < 0.05). Two rooms were 1) thermoneutral (Weeks 1 through 6, with decreasing maximum from 32 to 25°C and minimum from 28 to 19°C; relative humidity 49 to 58%) and 2) cyclic daily heat stress (Weeks 1 and 2, thermoneutral; Weeks 2 through 6, maximum temperatures 35, 35, 33, and 33°C, respectively; and minimum temperatures 23, 20, 19, and 19°C, respectively; relative humidity 51 to 54%). The DEB treatments (0, 140, 240, or 340 mEq Na + K - Cl/kg) had NaHCO3 plus NH4Cl, or KHCO3, or both added to corn-soybean meal mash basal diets with 0.30% salt (NaCl). In the thermoneutral room, DEB 240 increased 42-d weight gain and 44-d lymphocyte percentage and decreased heterophil percentage and heterophil to lymphocyte ratio compared to the DEB 40 treatment. The DEB 240 diets had 0.35 and 0.35% Na and 0.37% and 0.29% Cl in starter (0.75% K) and grower (0.67% K) diets, respectively. No DEB treatment differences were found in the heat stress room. For combined rooms, 42-d feed intake was higher for DEB 240 than for DEB 40. The 21-d weight gain was higher for DEB 240 than for DEB 40 or 140; and 21-d feed/gain was lower for DEB 40 than for DEB 340. The predicted maximum point of inflection for 21- and 42-d weight gains were DEB 250 and 201, with highest 42-d feed intake at 220.

The influence of dietary vitamin C and E supplementation on the physiological response of pirarucu, Arapaima gigas, in net culture

This study evaluated the efficacy of dietary vitamin C (ascorbic acid or AA), vitamin E (α-tocopherol or α-T), and C + E supplementation on the blood parameters of Arapaima gigas grown in net cages for 45 days. Four treatments were tested: control (commercial feed); C800; E500 and C + E (800 + 500) with supplementation of 800 mg AA kg- 1, 500 mg α-T kg- 1 and 800 + 500 mg AA + α-T kg- 1, respectively. Hematocrit (Ht), red blood cells (RBC), and hemoglobin concentration (Hb) (oxidative status indicators), thrombocytes and leukocytes (immunological indicators), plasma protein and glucose were evaluated. Fish fed vitamin C and C + E supplemented diets showed greater weight gain and survival. Dietary vitamin C and C + E diet supplementation resulted in increased Ht, Hb, RBC, MCHC, total leukocytes, total proteins, thrombocytes and eosinophils compared to the control and α-T. The α-tocopherol-supplemented diet reduced the number of total thrombocytes, lymphocytes and neutrophils and increased glucose and eosinophils relatively to the control. In general, leukocytes and thrombocytes were good indicators of the efficiency of vitamin on the defense mechanism of the A. gigas reared in cages. Results indicate that high α-T diet supplementation provides no benefit for the maintenance of the oxidative or the immunological status of A. gigas. However, it was demonstrated that high dietary AA improves A. gigas immunological status. Red blood cell indices and immune system indicators showed no synergistic effect between the vitamins after supplementing the A. gigas diet with α-T + AA. © 2006 Elsevier Inc. All rights reserved.

In vitro evaluation of surface roughness of 4 resin composites after the toothbrushing process and methods to recover superficial smoothness.

OBJECTIVE: This study evaluated the efficiency of repolishing, sealing with surface sealant, and the joining of both in decreasing the surface roughness of resin-based composites after a toothbrushing process. METHOD AND MATERIALS: Ten specimens of each composite (Alert, Z100, Definite, and Prodigy Condensable), measuring 2 mm in thickness and 4 mm in diameter, were made and submitted to finishing and polishing processes on both sides of the specimens using the Sof-Lex system. The specimens were then subjected to toothbrushing (30,000 cycles), and surface roughness (Ra) was analyzed with a Surfcorder SE 1700 profilometer. The upper surface of each composite was etched with 37% phosphoric acid, and the surface-penetrating sealant Protect-it was applied on 1 surface. The roughness of these surfaces was again measured. On the other side, the surface of the specimen was repolished, and the efficiency of this procedure was measured using the profilometer. The surface roughness resulting from the joining of the 2 methods was verified by applying, in the final stage, the surface-penetrating sealant on the repolished surface. Data were analyzed with analysis of variance and Tukey test (P <.05). RESULTS: Results showed that the lowest surface roughness values were obtained for Definite, Z100, and Prodigy Condensable after the repolishing process and after the repolishing plus sealing. For Alert, the joining of repolishing plus sealing promoted the lowest values of surface roughness. CONCLUSION: Of the resin-based composites, Alert demonstrated the highest values of surface roughness in all the techniques tested.

Influence of environmental temperature, dietary energy level and sex on performance and carcass characteristics of pigs

Pigs are quite sensitive to high environmental temperatures and the thermoregulation mechanisms represent great expenses in energy for heating loss, reducing animal well-being and production performance, and altering carcass quality. The aim of this study was to assess the effects of sex and dietary energy level in growing-finishing pigs submitted to characteristic seasonal variation of temperature in subtropical humid climate, and to propose a mathematical model to predict growth performance and carcass characteristics. Twenty-eight crossbred growing-finishing pigs were randomly allotted to twelve treatments, in a 2x2x3 factorial trial (2 sex; 2 environmental conditions, and 3 energy levels). Heat stress condition (climatic chamber) showed temperatures of 31 oC at 7:00 and 22 oC at 17:00 (maximum of 33 °C) and thermal comfort condition (stall) showed temperatures of 18 °C at 7:00 and 24 °C (maximum of 27 °C). Pigs were fed ad libitum with diets containing 12.2 (low), 13.6 (medium) and 15.0 (high) MJ ME/ kg DM. Voluntary feed intake, daily weight gain, and final body weight were higher (P<0.01) at thermal comfort condition and were influenced by sex (P<0.01) in growing pigs. Feed to gain ratio decreased as the energy level increased (P<0.01), with values of 2.67, 2.59, and 2.32 (12.2, 13.6, and 15.0 MJ ME/kg DM, respectively). There was energy level and sex interaction only for daily weight gain. Regarding finishing pigs, environmental conditions also showed effects (P<0.01) on voluntary feed intake, daily weight gain, and final body weight. Performance of pigs was better at thermal comfort condition. Feed to gain ratio values were 3.55, 3.42, and 2.95 for low, medium, and high energy level, respectively. Interactions between energy level and sex were observed for voluntary feed intake, daily weight gain, and final body weight (P<0.05). Carcass yield and quality were affected by environmental condition and dietary energy level. Both hot and cold carcass weight increased as energy of ration increased. Cold carcass weight increased by 1.142 kg/MJ EM whereas backfat thickness was up to 252 mm/MJ EM. Longissimus thoracis muscle thickness was around 16 mm smaller in pigs under heat stress, but lean content was 2.68% higher in those animals. Regression equations were proposed to predict the performance values in the different situations studied.

Effect of phosphate-bonded investments on titanium reaction layer and crown fit

This study analyzed the reaction layer and measured the marginal crown fit of cast titanium applied to different phosphate-bonded investments, prepared under the following conditions (liquid concentration/casting temperature): Rema Exakt (RE) - 100%/237°C, 75%/287°C, Castorit Super C (CS)-100%/70°C, 75%/141°C and Rematitan Plus (RP)-100%/430°C (special to titanium cast, as the control group). The reaction layer was studied using the Vickers hardness test, and analyzed by two way ANOVA and Tukey's HSD tests (α = 0.05). Digital photographs were taken of the crowns seated on the die, the misfit was measured using an image analysis system and One-way ANOVA, and Tukey's test was applied (α = 0.05). The hardness decreased from the surface (601.17 VHN) to 150 μm (204.03 VHN). The group CS 75%/141°C presented higher hardness than the other groups, revealing higher surface contamination, but there were no differences among the groups at measurements deeper than 150 μm. The castings made with CS - 100%/70°C presented the lowest levels of marginal misfit, followed by RE -100%/237°C. The conventional investments CS (100%) and RE (100%) showed better marginal fit than RP, but the CS (75%) had higher surface contamination.

Effect of brushing with conventional versus whitening dentifrices on surface roughness and biofilm formation of dental ceramics

The aim of this study was to evaluate the effect of conventional and whitening dentifrices on the weight loss, surface roughness, and early in situ biofilm formation on the surface of dental ceramics. Standardized feldspar ceramic specimens (Vita VM7 and Vita VM13) were submitted to the following experimental conditions: no brushing; brushing without a dentifrice; brushing with a conventional dentifrice; and brushing with a whitening dentifrice. A brushing machine was used to simulate brushing. The mass and surface roughness of all specimens from the test groups were evaluated prior to and after brushing. Ten participants used an oral device for eight hours to evaluate the biofilm formed in situ on the specimens. Scanning electron microscopy was used for qualitative and quantitative analysis of the biofilm. ANOVA and Tukey tests were used to analyze the results of weight loss, surface roughness, and presence of bacteria. A one-way Kruskal-Wallis test was used for bacterial colonization results. For both ceramics, brushing with a whitening dentifrice resulted in weight loss that was significantly greater when compared to brushing without a dentifrice or with a conventional dentifrice. Increased surface roughness was noticed on VM13 ceramic samples with both dentifrices, whereas only conventional dentifrice had a significant effect on the surface roughness of VM7 samples. For both VM7 and VM13, no difference was found between the experimental conditions with regard to the presence or number of bacteria. Cocci and short rods were the predominant microbial morphotypes. Granular or fibrillar acellular material partially covered the specimens. Brushing with a whitening dentifrice resulted in significant weight loss of ceramic restorations, while brushing with both conventional and whitening dentifrices can roughen ceramic surfaces. The increase in roughness was not clinically significant to contribute to increased biofilm formation.

Histological analysis of the osseointegration of Ti-30Ta dental implants after surface treatment

Metallic biomaterials are used to reinforce or to restore the form and function of hard tissues. Implants and prosthesis are used to replace shoulders, knees, hips and teeth. When these materials are inserted in bone several biological reactions happen. This process can be associated to surface properties (topography, roughness and surface energy). In this work, the influence of biomimetic surface treatment in the osseointegration of Ti-30Ta dental implants was evaluated. Ingots were obtained from titanium and tantalum by using an arc-melting furnace. They were submitted to heat treatment at 1,100°C for 1 h, cooled in water and cold worked by swaging. Then, screw-shaped implants (2.0 mm diameter by 2.5 mm length) were manufactured and they were implanted in a rat's femur. Animals were divided into two groups: untreated (control group) and treated (biomimetic surface treatment). They were sacrificed 30 days after implantation. For histological analysis, implants with surrounding tissue were removed and immersed in formaldehyde. Samples were embedded in polymethyl methacrylate and after polymerization, cut with a saw, polished and mounted on glass slides. The results obtained suggest that biomimetic surface treatment was able to promote an increase osseointegration on the surface of dental implants. © Springer-Verlag Berlin Heidelberg 2013.

Effect of dietary betaine supplementation on the performance, carcass yield, and intestinal morphometrics of broilers submitted to heat stress

The objective of this study was to evaluate the effect of betaine in methionine- and choline-reduced diets fed to broilers submitted to heat stress. In total, 1,408 male broilers were randomly distributed into eight treatments, according to 2 × 4 (environment x diet) factorial arrangement, with eight replicates of 2 birds each. Birds were reared environmental chambers under controlled temperature (25-26 °C) or cyclic heat-stressing temperature (25-31 °C). The following diets were tested: positive control (PC), formulated to meet broiler nutritional requirements; negative control (NC), with reduced DL-methionine and choline chloride levels; and with two supplementation levels of natural betaine to the negative control diet (NC+NB1 and NC+NB2). Live performance, carcass traits, and intestinal morphometrics were evaluated when broilers were 45 days of age. The results showed that all evaluated parameters were influenced by the interaction between environment and diet, except for breast meat drip loss. The breakdown of the interactions showed that birds fed the PC diet and reared in the controlled environment had greater breast drip loss than those submitted to the cyclic heat-stress environment. Birds submitted to cyclic heat stress and fed the PC diet presented the lowest feed intake. Feed conversion ratio was influenced only by diet. The FCR of broilers fed the NC+NB2 diet was intermediate relative to those fed the PC and NC diets. The addition of betaine in the diet, with 11.18% digestible methionine and 24.73% total choline reductions, did not affect broiler live performance, carcass yield, or intestinal morphometrics.

Ti-Mo alloys employed as biomaterials: Effects of composition and aging heat treatment on microstructure and mechanical behavior

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Effect of bleaching agents and soft drink on titanium surface topography

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Using phenology to assess urban heat islands in tropical and temperate regions

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)