Barium strontium titanate nanocrystalline thin films prepared by soft chemical method

Barium strontium titanate (Ba0.65Sr0.35TiO3) nanocrystalline thin films, which were produced by the soft chemical method, were crystallized at low temperature using a domestic microwave oven. A SiC susceptor were used to absorb the microwave energy and rapidly transfer the heat to the film. Low microwave power and short time have been used. The films obtained are crack-free, well-adhered, and fully crystallized. The microstructure displayed a polycrystalline nature with nanograin size. The metal-BST-metal structure of the thin films treated at 700 degrees C show food electric properties. The ferroelectric nature of the BST35 thin film was indicated by buttertly- shaped C-V curves. The capacitance-frequency curves reveal that the dielectric constant may reach a value up to 800 at 100kHz. The dissipation factor was 0.01 at 100kHz. The charge storage density as function of applied voltage graph showed that the charge storage densities are suitable for use in trench type 64 Mb ( 1-5 mu C/cm(2) and 265 Mb (2-11 mu C/cm(2)) DRAMs. (C) 2007 Elsevier Ltd. All rights reserved.

Synthesis and electrical characterization of CaBi2Nb2O9 thin films deposited on Pt/Ti/SiO2/Si substrates by polymeric precursor method

We report the successful deposition of CaBi2Nb2O9 (CBN) thin films on platinum coated silicon substrates by polymeric precursor method. The CBN thin films exhibited good structural, dielectric and CBN/Pt interface characteristics. The leakage current of the capacitor structure was around 0.15 A cm(-2) at an applied electric field of 30 kV cm(-1). The capacitance-voltage measurements indicated good ferroelectric polarization switching characteristics. The typical measured small signal dielectric constant and the dissipation factor at a frequency of 100 kHz were 90 and 0.053, respectively. The remanent polarization and the drive voltage values were 4.2 C cm(-2) and 1.7 V at an applied voltage of 10 V. No significant fatigue was observed at least up to 10(8) switching cycles. (c) 2005 Elsevier B.V. All rights reserved.

Low temperature synthesis and electrical properties of PbTiO3 thin films prepared by the polymeric precursor method

Ferroelectric PbTiO3 thin films were successfully prepared on a Pt(111)Ti/SiO2/Si(100) substrate for the first time by spin coating, using the polymeric precursor method. X-ray diffraction patterns of the films indicate that they are polycrystalline in nature. This method allows low temperature (500 degrees C) synthesis and high electrical properties. The multilayer PbTiO3 thin films were granular in structure with a grain size of approximately 110-120 nm. A 380-nm-thick film was obtained by carrying out four cycles of the spin-coating/heating process. Scanning electron microscopy (SEM) and atomic force microscopy (AFM) analyses showed the surface of these thin films to be smooth, dense and crack-free with low surface roughness (=3.4 nm). At room temperature and at a frequency of 100 kHz, the dielectric constant and the dissipation factor were, respectively, 570 and 0.016. The C-V characteristics of perovskite thin film prepared at low temperature show normal ferrolectric behavior. The remanent polarization and coercive field for the films deposited were 13.62 mu C/cm(2) and 121.43 kV/cm, respectively. The high electrical property values are attributed to the excellent microstrutural quality and chemical homogeneity of thin films obtained by the polymeric precursor method. (C) 2000 Elsevier B.V. S.A. All rights reserved.

A new implementation of population based incremental learning method for optimizations in electromagnetics

To enhance the global search ability of population based incremental learning (PBIL) methods, it is proposed that multiple probability vectors are to be included on available PBIL algorithms. The strategy for updating those probability vectors and the negative learning and mutation operators are thus re-defined correspondingly. Moreover, to strike the best tradeoff between exploration and exploitation searches, an adaptive updating strategy for the learning rate is designed. Numerical examples are reported to demonstrate the pros and cons of the newly implemented algorithm.

Tumor necrosis factor-alpha in gestation and puerperium of women with gestational hypertension and pre-eclampsia

Problem High plasma levels of tumor necrosis factor-alpha (TNF-alpha) in pregnant women have been associated with the pathogenesis of pre-eclampsia (PE). This study evaluated TNF-alpha plasma levels and monocyte production in gestational hypertension (GH) and PE during gestation and at puerperium.Method of study This study included 128 women, of whom 20 were non-pregnant (NP) normotensive (NT), and 108 were pregnant: 36 NT, 27 with GH, and 45 with PE. Peripheral blood plasma was used for TNF-alpha and uric acid determination. TNF-alpha was determined in plasma and lipopolysaccharide (LPS)-stimulated and non-stimulated monocyte supernatants by L929 bioassay.Results Tumor necrosis factor-alpha and uric acid plasma levels were higher in PE than in GH pregnancies. In both hypertensive groups, these parameters positively correlated and were significantly more elevated than in NT and NP women. TNF-alpha plasma levels and monocyte production were higher in hypertensive than in NT women during gestation, and significantly decreased at puerperium. Although decreased, TNF-alpha release in LPS-stimulated PE monocytes, was still significantly higher than in the other pregnant groups.Conclusion In vivo monocyte activation in GH and PE pregnant women was characterized by in vitro TNF-alpha production. The fact that higher circulating concentrations of TNF-alpha and uric acid were observed in PE than in GH suggests an association with disease severity.

Model approach for estimating potato pesticide bioconcentration factor

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Células sangüíneas, eletrólitos séricos, relação hepato e esplenossomáca de carpa-comum, Cyprinus carpio (Cyprinidae) na primeira maturação gonadal

This research studied the condition (Kn) relative factor, the hepatosomatic (HSR), the splenosomatic (SSR) relation, the erythrocytes, thrombocytes and leukocytes number, the glicogen locality by PAS method in thrombocytes and leucocytes and the total protein and electrolytes serices levels in both Cyprinus carpio L. sex. The female Kn showed higher value than the males. The female HSR average values were lower than the ones observed in males, while the leukocytes, lymphocytes and neutrophils percentage number were the highest. However, the males magnesium and choride serices levels were higher than the females. The HRS average values, hematocrit, haemoglobin concentration, average corspucular volume (ACV), average corpuscular haemoglobin concentration (ACHC), erythocytes number, trombocytes, monocytes, oesinophils, positive PAS leukocyte granular (PAS-LG), and total protein, sodium, potassium and calcium serices levels did not show significant statistics difference (p> 0.05) between males and females. The PAS method showed glicogen granules into the thronbocytes, eosinophils and neutrophils cytoplasm. Nevertheless, in the PAS-LG cytoplasm, neutral glicoprotein granules were also observed. Monocytes and lynfocytes showed negative reaction to PAS. In the teleosts, the gonodas matureness presents higher relation with the factor of condition. During the reprodution period it is unlikely to find the sexual effects isolated in the hemogram, because most of the time that is not the only factor to cause dimorphism.

A new implementation of Population Based Incremental Learning method for optimization studies in electromagnetics

To enhance the global search ability of Population Based Incremental Learning (PBIL) methods, It Is proposed that multiple probability vectors are to be Included on available PBIL algorithms. As a result, the strategy for updating those probability vectors and the negative learning and mutation operators are redefined as reported. Numerical examples are reported to demonstrate the pros and cons of the newly Implemented algorithm. ©2006 IEEE.

Detection of enterotoxin and toxic shock syndrome toxin 1 genes in Staphylococcus, with emphasis on coagulase-negative staphylococci

The detection of staphylococcal enterotoxins is decisive for the confirmation of an outbreak and for the determination of the enterotoxigenicity of strains. Since the recognition of their antigenicity, a large number of serological methods for the detection of enterotoxins in food and culture media have been proposed. Since immunological methods require detectable amounts of toxin, molecular biology techniques represent important tools in the microbiology laboratory. In the present study, polymerase chain reaction (PCR) was used to identify genes responsible for the production of enterotoxins and toxic shock syndrome toxin 1 (TSST-1) in S. aureus and coagulase-negative staphylococci (CNS) isolated from patients and the results were compared with those obtained by the reverse passive latex agglutination (RPLA) assay. PCR detection of toxin genes revealed a higher percentage of toxigenic S. aureus strains (46.7%) than the RPLA method (38.3%). Analysis of the toxigenic profile of CNS strains showed that 26.7% of the isolates produced some type of toxin, and one or more toxin-specific genes were detected in 40% of the isolates. These results suggests the need for further studies in order to better characterize the pathogenic potential of CNS and indicate that attention should be paid to the toxigenic capacity of this group of microorganisms.

Influence of resin composite insertion technique in preparations with a high C-factor

Objective: To evaluate the marginal microleakage in enamel and dentin/cementum walls in preparations with a high C-factor, using 3 resin composite insertion techniques. The null hypothesis was that there is no difference among the 3 resin composite insertion techniques. Method and Materials: Standardized Class 5 cavities were prepared in the lingual and buccal aspects of 30 caries-free, extracted third molars. The prepared teeth were randomly assigned to 3 groups: (1) oblique incremental placement technique, (2) horizontal incremental placement technique, and (3) bulk insertion (single increment). The preparations were restored with a 1-bottle adhesive (Single Bond, 3M ESPE) and microhybrid resin composite (Z100, 3M ESPE). Specimens were isolated with nail varnish except for a 2-mm-wide rim around the restoration and thermocycled (1,000 thermal cycles, 5°C/55°C; 30-second dwell time). The specimens were immersed in an aqueous solution of 50 wt% silver nitrate for 24 hours, followed by 8 hours in a photo-developing solution and evaluated for microleakage using an ordinal scale of 0 to 4. The microleakage scores obtained from occlusal and gingival walls were analyzed with Wilcoxon and Kruskal-Wallis nonparametric tests. Results: The null hypothesis was accepted. The horizontal incremental placement technique, the oblique incremental technique, and bulk insertion resulted in statistically similar enamel and dentin microleakage scores. Conclusion: Neither the incremental techniques nor the bulk placement technique were capable of eliminating the marginal microleakage in preparations with a high C-factor.

Study of the phenomena of fatigue using the finite element method

About 99% of mechanical failures are consequence of the phenomena of fatigue, which consists on the progressive weakening of the resistant section of a mechanical component due to the growing of cracks caused by fluctuating loadings. A broad diversity of factors influences the fatigue life of a mechanical component, like the surface finishing, scale factors, among others, but none is as significantly as the presence of geometric severities. Stress concentrators are places where fatigue cracks have a greater probability to occur, and so on, the intuit of this work is to develop a consistent and trustfully methodology to determine the theoretical stress concentration factor of mechanical components. Copyright © 2007 SAE International.

Characterization of language disorders in children with lead poisoning

Background: lead poisoning can have a negative impact on the neuropsychological functions, including language, due to the damage it causes to the developthent of the Central Nervous System. Aim: to verify the occurrence of language disorders in children who suffered from led poisoning and to verify the correlation between the lead concentration level in the blood and the language disorders presented by the children. Method: language evaluation of 20 preschoolers, with lead concentration level in the blood above 10μg/dl. Results: 13 children presented language impairment involving only phonology or more than one language subsystem. The statistical analysis indicated that no correlation exists between the severity of the language impairment and the concentration levels of lead. Conclusion: the number of children with language impairment indicates lead poisoning as a risk factor for the present alterations, even though other risk factors for language disorders were found and the absence of correlation between the investigated variables.

Metodologia para quantificação de leucóciotos totais em peixe Oreochromis Niloticus

Haematological investigation is an important part of disease diagnosis. The techniques used for mammals are generally applicable for fishes with slight modification. The presence of nucleated erythrocytes and thrombocytes in fish may cause some confusion in the identification of blood cells, mainly in total leukocytes count. This work evaluated two different methods (direct and indirect) of leukocytes counting. Specimens of tilapia were divided randomly into four groups of 48 fish each. Each group was further randomized into three replicate experiments of 16 fish per replicate in 40 L aquarium and maintained for 10 days. Counting of leukocytes in peripheral blood was determined in six fishes per group at the times: 0, 3, 7 and 10 days. The direct method in Neubauer chamber showed a large dispersion of data in regard to the average, the opposite was observed in indirect method determined in blood smears that showed more homogeneity among groups. Due to this factor the indirect method can be considered more accurate than the direct method for counting leukocytes in fishes.

A statistical analysis of loss factor to determine the energy losses

Given that the total amount of losses in a distribution system is known, with a reliable methodology for the technical loss calculation, the non-technical losses can be obtained by subtraction. A usual method of calculation technical losses in the electric utilities uses two important factors: load factor and the loss factor. The load factor is usually obtained with energy and demand measurements, whereas, to compute the loss factor it is necessary the learning of demand and energy loss, which are not, in general, prone of direct measurements. In this work, a statistical analysis of this relationship using the curves of a sampling of consumers in a specific company is presented. These curves will be summarized in different bands of coefficient k. Then, it will be possible determine where each group of consumer has its major concentration of points. ©2008 IEEE.

Comparison of methods for the detection of biofilm production in coagulase-negative staphylococci

Background: The ability of biofilm formation seems to play an essential role in the virulence of coagulase-negative staphylococci (CNS). The most clearly characterized component of staphylococcal biofilms is the polysaccharide intercellular adhesin (PIA) encoded by the icaADBC operon. Biofilm production was studied in 80 coagulase-negative staphylococci (CNS) strains isolated from clinical specimens of newborns with infection hospitalized at the Neonatal Unit of the University Hospital, Faculty of Medicine of Botucatu, and in 20 isolates obtained from the nares of healthy individuals without signs of infection. The objective was to compare three phenotypic methods with the detection of the icaA, icaD and icaC genes by PCR. Findings: Among the 100 CNS isolates studied, 82% tested positive by PCR, 82% by the tube test, 81% by the TCP assay, and 73% by the CRA method. Using PCR as a reference, the tube test showed the best correlation with detection of the ica genes, presenting high sensitivity and specificity. Conclusions: The tube adherence test can be indicated for the routine detection of biofilm production in CNS because of its easy application and low cost and because it guarantees reliable results with excellent sensitivity and specificity. © 2010 Cunha et al; licensee BioMed Central Ltd.