Efeitos de pontos de contato corporal e orientação segmentar na sensibilidade háptica durante o uso do sistema âncora em tarefas de controle postural

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Dinâmica não linear e projeto de controle em sistemas de transporte vertical: comportamentos periódicos e caóticos

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

A coupling technique for non-matching finite element meshes

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Simulação numérica do escoamento em difusores radiais com discos frontais fixos e móveis

Pós-graduação em Engenharia Mecânica - FEIS

Iniciação ao estudo da dinâmica de rotação de um satélite em variáves de Andoyer

The dynamics of the rotation of a satellite is an old and classical problem, specially in the Euler formalism. However, with these variables, even in torque free motion problem, the integrability of the system is far from trivial, mainly when the three moments of the inertia are not equal. Another disadvantage occurs when the inclinations between some plans are null or close to zero, so the nodes become undetermined. In this work, we propose the use of modern Andoyer's variables. These are a set of canonical variables and therefore some significant advantages can be obtained when dealing with perturbation methods. On other the hand, the integrability of the torque free motion becomes very clear, as the system is reduced to a problem of one degree of freedom. The elimination of the singularities mentioned above, can be solved very easily, with Pincaré-type variables. In this work we give the background concepts of the Andoyer's variables and the disturbing potential is obtained for the rotational dynamics of a satellite perturbed by a planet. In the case when A = B (moments of inertia) and due to the current variables, the averaged system is trivially obtained through very simple integrations

Dinâmica não linear e controle de um sistema vibratório modelado com memória de forma e, excitado por fontes de energia do tipo ideal e não ideal

Pós-graduação em Engenharia Mecânica - FEB

Time reduction of light curing: Influence on conversion degree and microhardness of orthodontic composites

Introduction: The aim of this study was to assess the influence of curing time and power on the degree of conversion and surface microhardness of 3 orthodontic composites. Methods: One hundred eighty discs, 6 mm in diameter, were divided into 3 groups of 60 samples according to the composite used-Transbond XT (3M Unitek, Monrovia, Calif), Opal Bond MV (Ultradent, South Jordan, Utah), and Transbond Plus Color Change (3M Unitek)-and each group was further divided into 3 subgroups (n = 20). Five samples were used to measure conversion, and 15 were used to measure microhardness. A light-emitting diode curing unit with multiwavelength emission of broad light was used for curing at 3 power levels (530, 760, and 1520 mW) and 3 times (8.5, 6, and 3 seconds), always totaling 4.56 joules. Five specimens from each subgroup were ground and mixed with potassium bromide to produce 8-mm tablets to be compared with 5 others made similarly with the respective noncured composite. These were placed into a spectrometer, and software was used for analysis. A microhardness tester was used to take Knoop hardness (KHN) measurements in 15 discs of each subgroup. The data were analyzed with 2 analysis of variance tests at 2 levels. Results: Differences were found in the conversion degree of the composites cured at different times and powers (P < 0.01). The composites showed similar degrees of conversion when light cured at 8.5 seconds (80.7%) and 6 seconds (79.0%), but not at 3 seconds (75.0%). The conversion degrees of the composites were different, with group 3 (87.2%) higher than group 2 (83.5%), which was higher than group 1 (64.0%). Differences in microhardness were also found (P < 0.01), with lower microhardness at 8.5 seconds (35.2 KHN), but no difference was observed between 6 seconds (41.6 KHN) and 3 seconds (42.8 KHN). Group 3 had the highest surface microhardness (35.9 KHN) compared with group 2 (33.7 KHN) and group 1 (30.0 KHN). Conclusions: Curing time can be reduced up to 6 seconds by increasing the power, with a slight decrease in the degree of conversion at 3 seconds; the decrease has a positive effect on the surface microhardness.