Obtenção e caracterização de nanofibras eletrofiadas via solução de quitosana com e sem inclusão de hidroxiapatita

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Osseointegração de implantes instalados sem estabilidade primária: o papel dos materiais à base de fibrina e fosfato de cálcio

When implants are installed immediately after tooth extraction may occur anchoring primary decreased, delay or failure of osseointegration process. This occurs because of the large interface between the surrounding walls of the socket and the surface of the implant. For reconstruction, replacement or filling of bone defects the solution can be obtained with the use of autogenous, heterogenous or allogeneic bone grafts. However, these grafts suffer certain drawbacks, particularly a high rate of donor site morbidity, limited amounts of available bone, and the additional operative time required for harvest. For these reasons, intensive efforts have been directed toward developing alternative substances for to either augment or substitute. In this paper, we will examine some of the commonly used materials : fibrin and calcium phosphate.

Efeito de diferentes gomas de mascar sobre o pH salivar de crianças

Objective: To evaluate the effect of different chewing gum brands on the salivary pH of children with primary dentition. Method: Forty children were selected and assigned to four groups: control (no chewing gum); sugarless chewing gum; chewing gum with casein phosphopeptide-amorphous calcium phosphate; and chewing gum with xylitol. The first saliva collection was made after supervised tooth brushing for stabilization of the oral pH. Next, all children were instructed to drink slowly 100 mL of a cola-based soft drink (Coca-Cola®) and a new saliva collection was made 10 min later. Then, each group chewed on the chewing gum for 5 min and discarded it after this time. Saliva was collected again at 5, 10 and 15 min intervals after start using the chewing gum. Measurement of salivary pH was made with colorimetric test papers and a digital pH-meter. Data were analyzed statistically by analysis of variance and Tukey’s test at a 5% significance level. Results: The use of chewing gums accelerated the increase of salivary pH to considerably alkaline levels after consumption of an acidic beverage, especially within the first minutes. The highest levels were obtained in the groups of children that used chewing gums containing xylitol and casein phosphopeptide-amorphous calcium phosphate. Conclusion: Children that used the chewing gums after ingestion of an acidic soft drink presented an increase in salivary pH, with the best results in the groups that used chewing gums containing casein phosphopeptide-amorphous calcium phosphate and xylitol.

Scaffold nanoestruturado utilizando-se celulose bacteriana/fosfatos de cálcio para regeneração óssea

Pós-graduação em Biotecnologia - IQ

Cimentos bioativos injetáveis funcionalizados com peptídeo osteogênico para reparação óssea

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Impacto de andrógenos na diferenciação e atividade de osteoclastos em cultura celular

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Efeito de diversos protocolos de dessensibilização dentinária na obliteração de túbulos dentinários, resistência de união do sistema adesivo e formação de camada hibrida na dentina cervical

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Dosimetric properties of UV irradiated calcium co-doped borate glass-ceramic

The thermoluminescence (TL) response of Dy and Li doped 20CaB(4)O(7)-80CaB(2)O(4) (Wt%) glass-ceramic irradiated with ultraviolet (UV) radiation was studied. In order to act as TL activator ions, the Dy and Li ions were included in the matrix during the melting process to increase its TL efficiency. A single crystalline CaB2O4 phase was present in the glass-ceramic as determined by X-ray diffraction (XRD). The glass-ceramic 20CaB(4)O(7)-80CaB(2)O(4):Dy,Li wt% (named 20CBO7:Dy,Li) is a newly prepared TL material. Its thermoluminescent dosimetric characteristics have shown a linear response under UV radiation exposure and a good TL signal reproducibility, thus proving to be a promising material for using as an ultraviolet radiation dosimeter. (C) 2007 Elsevier B.V. All rights reserved.

Effect of conditioning methods on the microtensile bond strength of phosphate monomer-based cement on zirconia ceramic in dry and aged conditions

The objective of this study was to evaluate the durability of bond strength between a resin cement and aluminous ceramic submitted to various surface conditioning methods. Twenty-four blocks (5 X 5 X 4 mm 3) of a glass-in filtrated zirconia-alumina ceramic (inCeram Zirconia Classic) were randomly divided into three surface treatment groups: ST1-Air-abrasion with 110-mu m Al2O3 particles + silanization; ST2-Laboratory tribochemical silica coating method (110-mu m Al2O3, ilO-PM Silica) (Rocatec) + silanization; ST3-Chairside tribochemical silica coating method (30-mu m SiOx) (CoJet) + silanization. Each treated ceramic block was placed in its silicone mold with the treated surface exposed. The resin cement (Panavia F) was prepared and injected into the mold over the treated surface. Specimens were sectioned to achieve nontrimmed bar specimens (14 sp/block) that were randomly divided into two conditions: (a) Dry-microtensile test after sectioning; (b) Thermocycling (TC)-(6,000X, 5-55 degrees C) and water storage (150 days). Thus, six experimental groups were obtained (11 = 50): Gr1-ST1 + dry; Gr2-ST1 + TC. Gr3-ST2 + dry; Gr4-ST2 + TC; Gr5-ST3 + dry; Gr6ST3 + TC. After microtensile testing, the failure types were noted. ST2 (25.1 +/- 11) and ST3 (24.1 +/- 7.4) presented statistically higher bond strength (MPa) than that of STI (17.5 +/- 8) regardless of aging conditions (p < 0.0001). While Gr2 revealed the lowest results (13.3 +/- 6.4), the other groups (21.7 +/- 7.4-25. 9 +/- 9.1) showed statistically no significant differences (two-way ANOVA and Tukey's test, a 0.05). The majority of the failures were mixed (82%) followed by adhesive failures (18%). Gr2 presented significantly higher incidence of ADHESIVE failures (54%) than those of other groups (p = 0.0001). Both laboratory and chairside silica coating plus silanization showed durable bond strength. After aging, airabrasion with 110-mu m Al2O3 + silanization showed the largest decrease indicating that aging is fundamental for bond strength testing for acid-resistant Arconia ceramics in order to estimate their long-term performance in the mouth. (c) 2007 Wiley Periodicals, Inc.

Heat treatment of pre-hydrolyzed silane increases adhesion of phosphate monomer-based resin cement to glass ceramic

This study evaluated the influence of different forms of heat treatment on a pre-hydrolyzed silane to improve the adhesion of phosphate monomer-based (MDP) resin cement to glass ceramic. Resin and feldspathic ceramic blocks (n=48, n=6 for bond test, n=2 for microscopy) were randomly divided into 6 groups and subject to surface treatments: G1: Hydrofluoric acid (HF) 9.6% for 20 s + Silane + MDP resin cement (Panavia F); G2: HF 9.6% for 20 s + Silane + Heat Treatment (oven) + Panavia F; G3: Silane + Heat Treatment (oven) + Panavia F; G4: HF 9.6% for 20 s + Silane + Heat Treatment (hot air) + Panavia F; G5: Silane + Heat Treatment (hot air) + Panavia F; G6: Silane + Panavia F. Microtensile bond strength (MTBS) test was performed using a universal testing machine (1 mm/min). After debonding, the substrate and adherent surfaces were analyzed using stereomicroscope and scanning electron microscope (SEM) to categorize the failure types. Data were analyzed statistically using two-way test ANOVA and Tukey's test (=0.05). Heat treatment of the silane containing MDP, with prior etching with HF (G2: 13.15 ± 0.89a; G4: 12.58 ± 1.03a) presented significantly higher bond strength values than the control group (G1: 9.16 ± 0.64b). The groups without prior etching (G3: 10.47 ± 0.70b; G5: 9.47 ± 0.32b) showed statistically similar bond strength values between them and the control group (G1). The silane application without prior etching and heat treatment resulted in the lowest mean bond strength (G6: 8.05 ± 0.37c). SEM analysis showed predominantly adhesive failures and EDS analysis showed common elements of spectra (Si, Na, Al, K, O, C) characterizing the microstructure of the glass-ceramic studied. Heat treatment of the pre-hydrolyzed silane containing MDP in an oven at 100 °C for 2 min or with hot air application at 50 ± 5 ºC for 1 min, was effective in increasing the bond strength values between the ceramic and resin cement containing MDP.

Enhanced solubilization of iron and calcium phosphates by Aspergillus niger by the addition of alcohols

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Sugarcane bagasse ash as a potential quartz replacement in red ceramic

Sugarcane bagasse ash (SCBA) is an industrial waste that contains silicon and aluminum oxides as the major components and iron, calcium, magnesium, and potassium oxides as the main minor components. In this paper, SCBA from one Brazilian factory was characterized and tested for its influence on the ceramic properties of clay/ash ceramic probes. Prismatic probes were pressed (18 MPa) using a ceramic mass mixed with 0%, 5%, 8%, and 10% ash. The probes were fired at temperatures between 800 degrees and 1200 degrees C. X-ray diffraction, X-ray fluorescence, thermal analysis (differential thermal analysis, thermo-gravimetric analysis/differential thermogravimetric analysis), and tests for texture (particle-size analysis), flexural strength, and linear shrinkage were carried out to characterize the samples. The results showed that the amount of ash to be incorporated will depend on mainly the composition of clay but also ash, and indicated that the clay used in this work can incorporate up to 10% weight of ash to produce solid bricks. The results also showed an improvement in ceramic/ash properties up to sintering temperatures higher than 1000 degrees C.

Biochemical, histopathological and clinical evaluation of delayed effects caused by methamidophos isoforms and TOCP in hens: Ameliorative effects using control of calcium homeostasis

This work evaluated the potential of the isoforms of methamidophos to cause organophosphorus-induced delayed neuropathy (OPIDN) in hens. In addition to inhibition of neuropathy target esterase (NTE) and acetylcholinesterase (AChE), calpain activation, spinal cord lesions and clinical signs were assessed. The isoforms (+)-, (+/-)- and (-)-methamidophos were administered at 50 mg/kg orally; tri-ortho-cresyl phosphate (TOCP) was administered (500 mg/kg, po) as positive control for delayed neuropathy. The TOCP hens showed greater than 80% and approximately 20% inhibition of NTE and AChE in hen brain, respectively. Among the isoforms of methamidophos, only the (+)-methamidophos was capable of inhibiting NTE activity (approximately 60%) with statistically significant difference compared to the control group. Calpain activity in brain increased by 40% in TOCP hens compared to the control group when measured 24h after dosing and remained high (18% over control) 21 days after dosing. Hens that received (+)-methamidophos had calpain activity 12% greater than controls. The histopathological findings and clinical signs corroborated the biochemical results that indicated the potential of the (+)-methamidophos to be the isoform responsible for OPIDN induction. Protection against OPIDN was examined using a treatment of 2 doses of nimodipine (1 mg/kg, i.m.) and one dose of calcium gluconate (5 mg/kg, iv.). The treatment decreased the effect of OPIDN-inducing TOCP and (+)-methamidophos on calpain activity, spinal cord lesions and clinical signs. (C) 2012 Elsevier B.V. All rights reserved.

Effects of calcium gluconate and PMSF in the treatment of acute intoxication of chicken by TOCP

To examine the efficacy of calcium gluconate (two doses of Ca-Glu 5 mg/kg i.v.) to alleviate the injurious effects of organophosphorus induced delayed neuropathy (OPIDN) in the presence or absence of phenylmethanesulfonyl fluoride (PMSF go mg/kg i.m.), 14 groups of four isabrown hens were used. To measure the lymphocyte neuropathy target esterase (LNTE)activity, groups receiving just distilled water (control), groups receiving just Tri-orto-cresyl phosphate (TOCP; 500 mg/kg p.o.) (Positive control), and other groups receiving TOCP and Ca-Glu or PMSF simultaneously or 12 hours later following intoxication by TOCP were used. They were sacrificed 12 and 24 hours after the administration of TOCP. To observe a 28-day time course of neurotoxicity scores and calcium plasma concentration, five groups were used. Regarding free Ca(2+)in the plasma, the positive control produced a characteristic profile time course up and down (luring 28 days, and some hens with maximum score of neurotoxicity in 28 days. The treatment, which prevented greater oscillation in free Ca(2+) in the plasma, presented a decrease in OPIDN in relation to the positive control. Twelve hours after the administration of TOCP, LNTE was 70-80% inhibited when compared with control, whereas the first decrease in the free Ca(2+) in the plasma was significantly different from the control only 24 hours after the administration of TOCP. In summary, the sooner the Ca-Glu is started, the less severe the neuropathy effects.

Calcium Hydroxide Mixed With Camphoric p-Monochlorophenol or Chlorhexidine in Delayed Tooth Replantation

This study evaluated the repair process after delayed replantation of rat teeth, using calcium hydroxide (Ca(OH)(2)) mixed with camphorated p-monochlorophenol (CMCP), chlorhexidine 2% (CHX), or saline as temporary root canal dressing to prevent and/or control inflammatory radicular resorption. Thirty Wistar rats (Rattus norvegicus albinos) had their right upper incisor extracted, which was bench-dried for 60 minutes. The dental papilla, the enamel organ, the dental pulp, and the periodontal ligament were removed. The teeth were immersed in 2% acidulated-phosphate sodium fluoride solution for 10 minutes. The root canals were dried with absorbent paper cones and divided into 3 groups of 10 animals according to root canal dressing used: group 1: Ca(OH)(2) + saline, group 2: Ca(OH)(2) + CMCP, and group 3: Ca(OH)(2) + CHX 2%. Before replanting, the teeth sockets were irrigated with saline. Histological analysis revealed the presence of inflammatory resorption, replacement resorption, and ankylosis in all 3 groups. Statistical analysis showed a significant difference between group 3 and the other groups. The use of Ca(OH)(2) mixed with CMCP or CHX did not show an advantage over the use of Ca(OH)(2) mixed with saline in preventing and/or controlling inflammatory resorption in delayed replantation of rat teeth.