Ethanol production by Zymomonas mobilis during sucrose fermentation: Optimization of culture conditions using factorial design

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Atletismo na educação física escolar: a elaboração colaborativa do software Atletic

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Mapeamento de ontologias empresariais para modelos de processos de negócio em BPMN, com aplicação em processos de software

Pós-graduação em Ciência da Computação - IBILCE

Identificação de funções de transferência de ordem fracionária utilizando como entrada um degrau

Pós-graduação em Engenharia Elétrica - FEIS

Improvement of water transport and carotenoid retention during drying of papaya by applying ultrasonic osmotic pretreatment

The effect of ultrasound and osmotic dehydration pretreatments on papaya drying kinetics was investigated. The ultrasound pretreatment was carried out in an ultrasonic bath at 30 A degrees C. The osmotic pretreatment in sucrose solution was carried out in an incubator at 34 A degrees C and agitation of 80 rpm for 210 min. The drying process was conducted in a fixed bed dryer at 70 A degrees C. Experimental data were fitted successfully using the Page model for dried fresh and pretreated fruits, with coefficient of determination greater than 0.9992 and average relative error lower that 14.4 %. The diffusional model was used to describe the moisture transfer, and the effective water diffusivity was identified in the order of 10(-9) m(2) s(-1). It was found that drying rates of osmosed fruits were the lowest due to the presence of infused solutes, while the ultrasound pretreatment contributed to faster drying rates. Evaluation of the dried fruit was performed by means of total carotenoids retention. Ultrasound treatments in distilled water prior to air-drying gave rise to dried papayas with retention of carotenoids in the range 30.4-39.8 % and the ultrasonic-assisted osmotic dehydration of papayas showed carotenoids retention values up to 64.9 %, whereas the dried fruit without pretreatment showed carotenoids retention lower than 24 %.

Improvement to the physical quality and imbibition pattern in seeds of candeia (Eremanthus incanus (Less.) Less.)

The objective of this work was to develop a methodology for seed processing and X-ray analysis and to study imbibition pattern in seeds of candeia (Eremanthus incanus). Seeds were gathered in 2001 and 2002 in Morro do Pilar and Lavras respectively, processed and stored in a cold chamber (5ºC/60%RH) until the start of experiments. In order to identify unfilled seeds, a protocol was developed for X-ray use combining radiation energy (Kv) and exposure time (seconds). For elimination of unfilled seeds, an experiment was conducted using a South Dakota seed blower whereby different opening settings and ventilation times were combined. Original seed lots and categorized lots following radiograph viewing were tested by germination tests, with seeds being cleansed in sodium hypochlorite and scattered over blotting paper in 'gerboxes' and then taken to germinators with alternating temperatures of 20º-30ºC and 10 hours of light, for up to 15 days. Imbibition curves were determined under the conditions 30ºC, 20º-30ºC/10 hours of light and 30º-20ºC/10 hours of light. The X-ray protocol that best allowed viewing of internal seed structures was 30Kv for 45 seconds. Seed separation using the blower setting at a 3.0 opening for 30 seconds raised the number of embryonic seeds to values exceeding 99%, also raising the germination rates as a consequence. The imbibition pattern is three-phased and the germination process is completed in 72 hours. Under alternate temperatures, primary root growth is favored.

Simulação sequencial na interpolação dos dados de entrada ou saída do modelo de lixiviação do software Araquá

Pós-graduação em Agronomia (Irrigação e Drenagem) - FCA

Um estudo de retas do plano e uma abordagem para o ensino médio com o software GeoGebra

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Solution heat treatment of plasma nitrided 15-5PH stainless steel - Part I: Improvement of the corrosion resistance

The results of the investigation on Solution Heat Treatment of Plasma Nitrided (SHTPN) precipitation-hardened steel 15-5PH are presented. The layers have been obtained by the plasma nitriding process followed by solution heat treatment at different temperatures. The influence of the solution heat treatment after nitriding on the dissolution process of the nitrided layer has been considered. The nitrided layers were studied by scanning electron microscopy, X-ray microanalysis (EDX), and X-Ray diffraction. Micro-hardness tests of the nitrided layers and solubilized nitrided layers have been carried out and interpreted by considering the processing conditions. It was found that high nitrogen austenitic cases could be obtained after SHTPN of martensitic precipitation-hardened steel (15-5PH). When Solution Heat Treatment (SHT) was performed at 1100 °C, some precipitates were observed. The amount of precipitates significantly reduced when the temperature increased. The EDX microanalysis indicated that the precipitate may be chromium niobium nitride. When the precipitation on the austenite phase occurred in small amount, the corrosion resistance increased in SHTPN specimens and the pit nucleation potential also increased. The best corrosion result occurred for SHT at 1200 °C.

Um estudo sobre a utilização do software SCRATCH como ferramenta de apoio ao ensino da disciplina de lógica de programação

Learning to program or master a programming language is not an easy task, and the base of process should by study Logic Programming, beginning to learning through the development of pseudocodes, algorithms and flowcharts, for, techniques that facilitate the construction and understanding of what you want to accomplish, to that is subsequently developed or elaborated a program. Reflecting on the learning of Logic Programming, this article presents information about software SCRATCH in relation to logic (pseudocodes), and how it provides support to the understanding of student learning in this course.

Análise de cenários para auxílio à tomada de decisão no plantio mecanizado de cana-de-açúcar

Pós-graduação em Agronomia (Ciência do Solo) - FCAV

Estudo do peso metabólico e índice de Kleiber na estimação de parâmetros genéticos de características ponderais em uma população de bovinos de raça brahman

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Cenários da expansão urbana e da legislação e os reflexos na cobertura vegetal arbórea e arbustiva na cidade de Americana-SP

Pós-graduação em Geografia - IGCE

Utilização de trocadores de calor de placas em espiral em processos da indústria siderúrgica

Stricter environmental policies are shown necessary to ensure an effective pollutant emission control. It is expected for the present year of 2015, that Brazil will assume, at the 21th United Nation's Climate Change Conference (COP21), implementation of commitment to a low carbon economy. This positioning affects the industrial environment, so that is deemed necessary to search for new technologies, less aggressive to the environment, so the adequacies to the new emission policies do not cause a negative effect on production. Almost all of the processes performed in the steel industry demand burning fuel and, therefore, flue gases are sent to the atmosphere. In this present work is discussed the utilization of heat exchangers so, by recovering part of the available heat from the flue gases of certain industrial process, the combustion air is preheated. The combustion air preheat results in less energy requirement, i.e., less need of fuel consumption and, in addition, minor amount of pollutants to be emitted. Due to better fitting to the process, it is studied the utilization of spiral plate heat exchangers. The heat exchanger dimensioning is made by an iterative method implemented in the software Microsoft Excel. Subsequently are analyzed the gains in terms of process's thermal efficiency improvement and the percentage of fuel saving. The latter implies in reduction of the same percentage of greenhouse gases emission

Avaliação do software Autodesk Revit 2016 para quantificação por meio da modelagem da informação da construção

The building budgeting quickly and accurately is a challenge faced by the companies in the sector. The cost estimation process is performed from the quantity takeoff and this process of quantification, historically, through the analysis of the project, scope of work and project information contained in 2D design, text files and spreadsheets. This method, in many cases, present itself flawed, influencing the making management decisions, once it is closely coupled to time and cost management. In this scenario, this work intends to make a critical analysis of conventional process of quantity takeoff, from the quantification through 2D designs, and with the use of the software Autodesk Revit 2016, which uses the concepts of building information modeling for automated quantity takeoff of 3D model construction. It is noted that the 3D modeling process should be aligned with the goals of budgeting. The use of BIM technology programs provides several benefits compared to traditional quantity takeoff process, representing gains in productivity, transparency and assertiveness