Estudo da influência das resinas termofixas uréia formaldeído (UF) e melamina formaldeído (MF) nas características físicas e mecânicas de painéis MDF

Thermosetting resins are very important in the production of MDF panels. They act as an adhesive in the process of compacting and consolidating the fiberboard. Thermoset resins commonly used in this process are based resin urea formaldehyde (UF) and melamine formaldehyde (MF). The first has a higher demand due to its low cost and good performance in meeting the specifications and standards. The second has a high cost compared to MF resin, but adds greater value to the MDF panel, because it gives greater moisture resistance. The process of manufacture of MDF boards was briefly presented in this study to facilitate the understanding of the work. Samples of thermosetting resins (UF and MF) were subjected to physical-chemical seeking to relate these results to the technological performance presented by their respective samples of MDF boards. Two other samples of MDF panels were subjected to physical and mechanical tests. Results were analyzed and related to the award of their respective thermoset resin. Instruments like Dahmos Trend Manager ® and Grecon Dax 5000 and TG - DSC analysis were used in this study to assist in the analysis of the results. It was observed that the results of the analysis of thermosetting resins were within the specified. Such resins do not directly influence the technological tests provided by the MDF panels, but it has been found that the process variables such as humidity and fiber production rate interfere with the performance of the resin accelerating the reaction and therefore their influence on the physical-mechanical properties of the panels MDF. Samples of MDF panels with UF and MF met all the specifications required by the Brazilian standard with regard to the technological quality. The increased demand for UF resin market is justified by the service specifications...

Efeito de fontes de luz na microdureza de resinas compostas

This study assessed the surface microhardness of compound resins cured by different light sources. Methods Three micro hybrid (Vit-l-escence, Amelogen Plus, Opallis) and one nanoparticle (Filtek Z350, 3M ESPETM Dental Products, St. Paul, USA) compound resins were selected. The resins were polymerized by a halogen light unit (Ultralux, Dabi Atlante, Ribeirão Preto, Brasil) with two tips, one semi-guided made of glass and another of painted acrylic and a LED-based source (UltraLume 2, Ultradent®, South Jordan, USA). Specimens constructed from a circular aluminum matrix were photopolymerized for 40 second after they received the compound resin and stored dry for 24 hours. After this period, a Vickers surface microhardness assay was performed, measuring the top (hardness 1) and base (hardness 2) surfaces four times each. Variance analyses were complemented by Newman-Keuls method, with significance set at 5%. Results The Opallis (FGM, Santa Catarina, Brasil) resin subjected to UltraLume 2 (Ultradent®, South Jordan, USA) obtained the lowest mean hardness values for the top surface. The Vit-l-escence (Ultradent®, South Jordan, USA) compound cured by Led UltraLume 2 (Ultradent®, South Jordan, USA) and by Ultralux PCP (Dabi Atlante, Ribeirão Preto, Brasil) halogen light obtained the highest mean hardness, followed by the Filtek Z350 (3M ESPETM Dental Products, St. Paul, USA) resin subjected to UltraLume 2 (Ultradent® South Jordan, USA). The Opallis (FGM, Santa Catarina, Brasil) resin cured by LED UltraLume 2 (Ultradent®, South Jordan, USA) also obtained the lowest mean hardness for the base surface and the Vit-L-Escence (Ultradent®, South Jordan, USA) resin obtained the highest value, followed by Amelogen Plus, when cured by Ultralux (Dabi Atlante, Ribeirão Preto, Brasil) using the semi-guided tip. Conclusion The polymerization and, consequently, the microhardness achieved by the LED unit was equivalent to those achieved by conventional halogen units for three of the four composites tested.

Análise comparativa da rugosidade superficial de resinas compostas de alta densidade

The success achieved by the use of composite resins in anterior teeth precipitately leads their use in posterior teeth. However, the indiscriminate application of these materials in cavities with several diverse sizes rapidly pointed out their lack of resistance to oclusal and proximal wear. OBJECTIVE: To evaluate the surface roughness of composite resin in relation to finishing and polishing technique. MATERIAL AND METHODS: Eight experimental groups (n = 15) were divided according to finishing and polishing technique: G1 – Z250TM composite resin without surface finishing and polishing; G2 – Z250TM composite resin plus surface finishing and polishing; G3 – P60TM composite resin without surface finishing and polishing; G4 – P60TM composite resin plus surface finishing and polishing; G5 – Prodigy CondensableTM composite resin without surface finishing and polishing; G6 – Prodigy CondensableTM composite resin plus surface finishing and polishing; G7 – SurefillTM composite resin without surface finishing and polishing; G8 – SurefillTM composite resin plus surface finishing and polishing. Three packable and one microhybrid (control group) composite resin was used. The surface roughness was measured using a profilometer at three points in each sample. The results were evaluated by ANOVA and Tukey test (p < 0.05). RESULTS: Prodigy CondensableTM composite resin showed the lowest surface roughness, while SurefillTM showed the highest surface roughness. Comparing the resins used, only between P60TM and SurefillTM there were no statistically significant differences (p > 0,05). CONCLUSION: Surface roughness was lower in all types of resin composites surfaces in contact with Mylar matrix strip than in areas submitted to finishing and polishing procedure.

Reabilitação estética funcional associando onlays em cerômero e resinas nanoparticuladas

Introdução: a perda da dimensão vertical de oclusão (DVO) é resultada de um grande desequilíbrio oclusal, onde não apenas a perda dos dentes pode ser o fator responsável, mas também as parafunções, entre elas, o bruxismo. O restabelecimento da relação maxilomandibular é condição necessária para que uma adequada reabilitação bucal seja executada, devolvendo, assim, função e estética perdidas. Objetivo: descrever um caso clínico de reabilitação em paciente bruxista, com presença de desgastes dentários, desgastes de tratamentos restauradores previamente existentes, fratura de onlay e bordas incisais, restabelecendo uma nova DVO por meio de onlays posteriores em cerômeros, recuperando a estética com restaurações diretas em resinas compostas nos dentes anteriores. Conclusões: a reabilitação bucal com levante de mordida em onlays devolve a DVO perdida de maneira segura.

Nanotubos óxidos aplicados a resinas compostas fotoativadas

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Contração de polimerização e expansão higroscópica de resinas compostas: análise pela técnica de video-imagem

To evaluate the volumetric changes due to polymerization and thermocycling on different resin-composites. Methods: Thirteen A2 Universal Dentin shade resin-composites (n = 10) from eight manufacturers were evaluated (4Seasons, Grandio, Venus, Amelogen Plus, P90, Z350, Esthet-X, Amaris, Vita-l-escence, Natural-Look, Charisma, Z250 and Opallis). The polymerization shrinkage percentage (PS) was calculated using an image measurement device (ACUVOL - Bisco Dental). Equal volumes of material, standardized by a semisphere polyurethane matrix (d = 3mm) were used and, after 5 minutes of relaxation, the baseline volume measurements were obtained with 18 J of energy dose from the LED light-curing unit. Measurements were obtained after 5 minutes and PS values calculated. Specimens were stored in a drydark environment for 24 hours and re-measured. Specimens were then thermocycled in distilled water between 5oC and 55oC for 20,000 cycles, subjected to another volume measurement at 5,000 cycle intervals. Specimens were gently dried prior to each measurement. Results: Repeated measurements were made using ANOVA (α = 0.05) showed that all resin-composite volumes were influenced by the number of cycles. Volumes at 5 minutes post-polymerization (12.47 ± 0.08) were significantly lower than those at baseline (12.80 ± 0.09). Volumes at 24 hours (12.43 ± 0.19) were insignificantly lower than those at 5 minutes postpolymerization. With regards to the impact of thermocycling, all specimens showed statistically significant increases in volume after 5,000 cycles (13.04 ± 0.22). Although statistically different from those after 5,000 cycles, there was no statistically significant difference between volumes measured at 10,000 (12.87±0.21), 15,000 (12.92±0.24), and 20,000 (12.84±0.23) cycles. Conclusion: According to the video-imaging analysis, thermocycling caused a significant expansion in resin-composites tested, the volume increase was not able to...

Influência do tratamento clareador e envelhecimento induzido sobre o brilho, cor, dureza e rugosidade superficial de resinas compostas

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Alteração cromática de resinas compostas laboratoriais submetidas à imersão em diferentes soluções

The pigmentation of indirect composite resins has been one of the most common reasons that lead the restorative treatment to failure. The purpose of this study was to investigate the effect of different solutions on color stability of indirect composite resins. Five brands of indirect composite resins were tested: Adoro, Resilab, Cristobal, Sinfony and Epricord. The samples were immerged in eleven solutions (n=10): common liquid foods (coke soft drink, red wine, coffee and orange juice), mounthrinses (Listerine, Oral-B, Colgate Plax and Periogard) and bleaching agents (carbamide peroxide 16%, 7.5% and hydrogen peroxide 38%) and artificial saliva (control group). The color was measured by a spectrophotometer before and after 7, 14 and 21 days of immersion in common liquid foods, after 12, 24, 36 and 60 hours of immersion in mounthrinses and after 7 and 14 days of immersion in bleaching agents. The Cristobal and Adoro resins showed highest values of ΔE statistically significant compared to the others resin brands. Adoro’s ΔE values changed significantly after the immersion process in red wine and coffee and also between periods measured. The resins Cristobal and Sinfony showed the highest values of ΔE after the immersion process in Listerine with difference statistically significant in comparison to control group. Besides, there was difference statistically significant of the ΔE values  for  Cristobal  after  immersion  in hydrogen peroxide 7,5% in comparison to control group. It can be conclude that all the solutions promoted color change on the indirect composite resins. However, ΔE values  are  whitin  the  values clinically acceptable.

Emprego de carvão ativado e resinas de troca ionica na remoção de substâncias orgânicas contaminantes do alcool etílico

This work had with objective to characterize and evaluate the performance of the combined system, involving activated charcoal and ionic exchange resins in the removal of substances organic contaminating of the ethyl alcohol from the fermentation of the cassava starch. To testing was used ethyl alcohol PA 96 oGL, conductivity of 0.90 μS/cm at 25 oC, acidity of 60 mg/L and Barbet test of 43 minutes at 15 oC. The contaminated alcohol was composed of ethyl alcohol additive of higher alcohols, organic acids, ester, diol, aldehydes, ketone and ether. Contaminated alcohol was added 2% activated charcoal and after the adsorption isotherm in ionic exchange resins was tested. The adsorption with activated charcoal was performed in a Water Bath at 30 oC for one hour and a half and shaking. Already adsorption ionic exchange columns occurred at room temperature on columns of 93,4 cm in filling height and diameter of 2.29 cm, for flows of 180 mL/min and 90 mL/min. Samples were collected in the tests with charcoal and with each one of the resins and the following analyses were performed: conductivity, acidity and Barbet test. The medium values for conductivity, acidity and Barbet test after the adsorption in charcoal and cation and anion resins were respectively: conductivity was 240; 354 and 465 μS/cm to 25 oC; acidity of 1.081; 1.103 and 1.062 mg/L and the Barbet test was 21; 20 and 9 minutes to 15 oC. It was observed that the addition of 2% of activated charcoal and the permanence in the columns of adsorption was not sufficient to remove the organic substances contaminating of the ethyl alcohol.

Avaliação mecânica e microbiológica de resinas acrílicas reforçadas com partículas de sílica revestidas com prata

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Análise da efetividade de polimerização, adaptação marginal e interna de restaurações Classe II de resinas compostas de inserção em bloco utilizando diferentes matrizes

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Avaliação da resistência de união de reparos em resinas compostas convencionais e bulkfill

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Biocompatibilidade de resinas acrílicas para base e reembasamento de próteses após períodos de imersão em soluções desinfetantes: análise do metabolismo celular

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Trigona spinipes (Fabr.) (Hymenoptera: Apidae) em espécies de maracujazeiro: flutuação populacional, horário de visitação e danos às flores

Avaliou-se a infestação, flutuação populacional e horário de visitação de Trigona spinipes (Fabr.) (Hymenoptera: Apidae) em espécies de maracujazeiro. As espécies utilizadas foram Passiflora coccinea, P. setacea, P. alata, P. edulis f. flavicarpa, P. laurifolia e P. nitida, aos três anos de idade. O ensaio foi conduzido em parcelas de 1,5 m de comprimento, avaliando-se os dois lados da espaldeira, considerando-se apenas o 0,5 m superior desta e totalizando, para os dois lados, a área de 1,5 m². Avaliaram-se os seguintes parâmetros: número de irapuás e porcentagem de dano nos botões florais, flores, frutos, ramos, folhas e pedúnculos. Para a determinação do horário de visitação, foi utilizada P. coccinea, sendo as avaliações realizadas às 9:00h, 12:00h e 15:00h. A correlação entre o número médio de T. spinipes presentes nas flores de espécies de maracujazeiro e a porcentagem de danos foi positiva e significativa (r = 0,99). em nenhuma das observações efetuadas, constatou-se a presença de T. spinipes nos botões florais, frutos, ramos, folhas ou pedúnculos das espécies de maracujazeiro, não ocorrendo danos nessas estruturas. Esse resultado sugere que as abelhas são atraídas pelas flores ocasionando danos nessas estruturas, provavelmente, por utilizar o tecido floral ou resinas contidas neste para a construção de ninhos. P. coccinea foi a espécie mais danificada por T. spinipes, apresentando suscetibilidade ao ataque desse inseto. Os horários de maior incidência de T. spinipes foram 9:00h e 12:00h, ocorrendo decréscimo significativo no número de abelhas por flor às 15:00h. Constatou-se maior infestação de T. spinipes nas flores das plantas de maracujá nos meses de outubro a novembro, coincidindo com a primavera, em Jaboticabal, SP.