Efeitos da injunção da base nas orientações interior e exterior e nas coordenadas do espaço objeto em imagens obtidas com a estéreo vídeo-câmara de um sistema móvel de mapeamento

In general, a land-based mobile mapping system is featured by a vehicle with a pair of video cameras mounted on the top and positioning and navigation sensors loaded in the vehicle. Considering the pair of video cameras mounted on the roof of the vehicle as a stereo camera pointing forward with both optical axes parallel to each other and orthogonal to the stereo base, whose length is 0.94 m, this paper aims at analyzing the interior and exterior camera orientation and the object point coordinates estimated by phototriangulation when the length constraint related to the stereo base is considered or not. The results show that the stereo base constraint has effect ouver the convergence estimation, but does it neither improves the object point coordinate estimation at significance level of 5% and nor it influences the interior orientation parameters. Finally, it has been noticed that the optical axes are not truly parallel to each other and orthogonal to the stereo base. Additionally, it has been observed that there is a convergence of approximately 0.5 degrees in the optical axes and they are not in the same plane (approximately 0.8 degrees deviation).

Chemical and Bioactive Quality Traits During Fruit Ripening in Eggplant (S-melon gena L.) and Allied Species

A chemical and bioactive quality evaluation of phytochemicals content of 10 eggplant lines and three allied species (S. sodomaeum, S. aethiopicum and S. integrifolium) was performed. The eggplant lines were divided into the two subgroups of delphinidin-3-rutinoside (D3R) and nasunin (NAS) typologies, on the basis of the anthocyanin detected in their fruit skin. The allied species had higher glycoalkaloids content, lower soluble solids and PPO activity and absence of anthocyanins compared to the eggplant lines; S. sodomaeum stood out for high phenols content. Orthogonal contrast revealed a higher sugar content and low PPO activity in NAS- compared to D3R-typologies, whereas higher chlorogenic acid and anthocyanin contents were present in D3R-typologies. The main effect of the ripening was a decrease in phenols and in the PPO activity, not evidenced in S. sodomaeum, and an increase of glycoalkaloids in overripe fruits.A good relationship was found between superoxide anion scavenging capacity and chlorogenic acid. This study highlighted the pattern of accumulation, also evidencing variations, of several phytochemicals during the eggplant fruit development and ripening.

Análise da aceitação de aguardentes de cana por testes afetivos e mapa de preferência interno

A aceitação de 11 amostras de aguardentes de cana envelhecidas e não envelhecidas foi avaliada por testes sensoriais afetivos e análises estatísticas uni e multivariada. As aguardentes estudadas compreenderam seis amostras comerciais de diferentes marcas, (sendo três não envelhecidas e três envelhecidas) e ainda outras cinco amostras correspondentes a zero, 12, 24, 36 e 48 meses de envelhecimento em um tonel de carvalho de 200L. As amostras foram avaliadas por 100 provadores consumidores do produto, recrutados por questionário de avaliação quanto à afetividade. Para os testes afetivos foi utilizada escala hedônica não estruturada de 9cm, sendo os dados obtidos avaliados por dois métodos estatísticos distintos: o Mapa de Preferência Interno (MDPREF) e a análise de variância univariada (ANOVA) com comparação de médias pelo teste de Tukey e análise de correlação. As amostras de aguardente envelhecidas por 12, 36 e 48 meses obtiveram maior aceitação, com médias ao redor de 7,0 na escala hedônica. A amostra com menor aceitação foi a correspondente ao tempo zero de envelhecimento (controle). As demais amostras obtiveram aceitação intermediária. A análise por MDPREF gerou em espaço multidimensional (onde as variações com relação aos dados de preferência foram extraídas em eixos ortogonais e para cada dimensão de preferência), coordenadas relativas aos produtos, que foram geradas em função da resposta dos consumidores. Os dados de aceitação de cada provador foram utilizados para o desenvolvimento de vetores individuais de preferência, resultando na construção de um mapa mutidimensional das amostras, em função dos dados de aceitação. No presente estudo o MDPREF foi gerado pelas primeira e segunda dimensões de preferência, as quais explicaram em conjunto 89,83% das variações observadas entre as amostras com relação à aceitação. O MDPREF confirmou os resultados da ANOVA, indicando uma maior preferência dos provadores pelas amostras de aguardentes envelhecidas. Os resultados sugerem também que aguardentes envelhecidas por mais de 24 meses em tonel de carvalho de 200L são preferidas pelos consumidores, em detrimento das comerciais não envelhecidas e mesmo das comerciais envelhecidas, que podem ser adicionadas de aguardente não envelhecida (processo denominado corte) e também ter correção da cor, conforme permite a Legislação Brasileira. O conteúdo de polifenóis totais e a intensidade de cor também foram determinados, e ambos apresentaram correlação linear positiva significativa (p<=0,05) com o aumento do tempo de envelhecimento das amostras.

3-(1-Hydroxy-2-phenylprop-2-en-1-yl)phenol

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Ethyl (E)-2-methoxyimino-2-(4-nitrobenzoyl)acetate

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

(Z)-Ethyl 2-hydroxyimino-2-(4-nitrobenzyl)ethanoate

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Two-dimensional modeling of material failure in reinforced concrete by means of a continuum strong discontinuity approach

The paper presents a new methodology to model material failure, in two-dimensional reinforced concrete members, using the Continuum Strong Discontinuity Approach (CSDA). The mixture theory is used as the methodological approach to model reinforced concrete as a composite material, constituted by a plain concrete matrix reinforced with two embedded orthogonal long fiber bundles (rebars). Matrix failure is modeled on the basis of a continuum damage model, equipped with strain softening, whereas the rebars effects are modeled by means of phenomenological constitutive models devised to reproduce the axial non-linear behavior, as well as the bondslip and dowel effects. The proposed methodology extends the fundamental ingredients of the standard Strong Discontinuity Approach, and the embedded discontinuity finite element formulations, in homogeneous materials, to matrix/fiber composite materials, as reinforced concrete. The specific aspects of the material failure modeling for those composites are also addressed. A number of available experimental tests are reproduced in order to illustrate the feasibility of the proposed methodology. (c) 2007 Elsevier B.V. All rights reserved.

Optimization of acid hydrolysis from the hemicellulosic fraction of Eucalyptus grandis residue using response surface methodology

Biotechnological conversion of biomass into fuels and chemicals requires hydrolysis of the polysaccharide fraction into monomeric sugars. Hydrolysis can be performed enzymatically and with dilute or concentrate mineral acids. The present study used dilute sulfuric acid as a catalyst for hydrolysis of Eucalyptus grandis residue. The purpose of this paper was to optimize the hydrolysis process in a 1.41 pilot-scale reactor and investigate the effects of the acid concentration, temperature and residue/acid solution ratio on the hemicellulose removal and consequently on the production of sugars (xylose, glucose and arabinose) as well as on the formation of by-products (furfural, 5-hydroxymethylfurfural and acetic acid). This study was based on a model composition corresponding to a 2 3 orthogonal factorial design and employed the response surface methodology (RSM) to optimize the hydrolysis conditions, aiming to attain maximum xylose extraction from hemicellulose of residue. The considered optimum conditions were: H2SO4 concentration of 0.65%, temperature of 157 degrees C and residue/acid solution ratio of 1/8.6 with a reaction time of 20 min. Under these conditions, 79.6% of the total xylose was removed and the hydrolysate contained 1.65 g/l glucose, 13.65 g/l xylose, 1.55 g/l arabinose, 3.10 g/l acetic acid, 1.23 g/l furfural and 0.20 g/l 5-hydroxymethylfurfural. (c) 2006 Published by Elsevier Ltd.

Electrodeposition of copper on titanium wires: Taguchi experimental design approach

Electrodeposition of thin copper layer was carried out on titanium wires in acidic sulphate bath. The influence of titanium surface preparation, cathodic current density, copper sulphate and sulphuric acid concentrations, electrical charge density and stirring of the solution on the adhesion of the electrodeposits was studied using the Taguchi statistical method. A L(16) orthogonal array with the six factors of control at two levels each and three interactions was employed. The analysis of variance of the mean adhesion response and signal-to-noise ratio showed the great influence of cathodic current density on adhesion. on the contrary, the other factors as well as the three investigated interactions revealed low or no significant effect. From this study optimized electrolysis conditions were defined. The copper electrocoating improved the electrical conductivity of the titanium wire. This shows that copper electrocoated titanium wires could be employed for both electrical purpose and mechanical reinforcement in superconducting magnets. (C) 2008 Elsevier B.V. All rights reserved.

Molecular assay optimized by Taguchi experimental design method for venous thromboembolism investigation

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Heat transfer in laminar flow of non-Newtonian fluids in ducts of elliptical section

Laminar forced convection inside tubes of various cross-section shapes is of interest in the design of a low Reynolds number heat exchanger apparatus. Heat transfer to thermally developing, hydrodynamically developed forced convection inside tubes of simple geometries such as a circular tube, parallel plate, or annular duct has been well studied in the literature and documented in various books, but for elliptical duct there are not much work done. The main assumption used in this work is a laminar flow of a power flow inside elliptical tube, under a boundary condition of first kind with constant physical properties and negligible axial heat diffusion (high Peclet number). To solve the thermally developing problem, we use the generalized integral transform technique (GITT), also known as Sturm-Liouville transform. Actually, such an integral transform is a generalization of the finite Fourier transform where the sine and cosine functions are replaced by more general sets of orthogonal functions. The axes are algebraically transformed from the Cartesian coordinate system to the elliptical coordinate system in order to avoid the irregular shape of the elliptical duct wall. The GITT is then applied to transform and solve the problem and to obtain the once unknown temperature field. Afterward, it is possible to compute and present the quantities of practical interest, such as the bulk fluid temperature, the local Nusselt number and the average Nusselt number for various cross-section aspect ratios. (C) 2006 Elsevier. SAS. All rights reserved.

Identification of Mechanical Systems through Kautz Filter

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

A Comparison of the Effects of Nonlinear Damping on the Free Vibration of a Single-Degree-of-Freedom System

This article concerns the free vibration of a single-degree-of-freedom (SDOF) system with three types of nonlinear damping. One system considered is where the spring and the damper are connected to the mass so that they are orthogonal, and the vibration is in the direction of the spring. It is shown that, provided the displacement is small, this system behaves in a similar way to the conventional SDOF system with cubic damping, in which the spring and the damper are connected so they act in the same direction. For completeness, these systems are compared with a conventional SDOF system with quadratic damping. By transforming all the equations of motion of the systems so that the damping force is proportional to the product of a displacement dependent term and velocity, then all the systems can be directly compared. It is seen that the system with cubic damping is worse than that with quadratic damping for the attenuation of free vibration. [DOI: 10.1115/1.4005010]

Ritmo Circadiano de Triiodotironina (T3) e Tiroxina (T4) Plasmática em Ovelhas Ideal durante o Anestro Estacional

The objective was to determine the plasma levels of the triiodothyronine (T-3) and thyroxine (T-4), in six Ideal ewe sheeps during seasonal anoestrus, by radioimmunoassay. The blood samples were collected from the jugular vein catheter over a period of 24 hours, at 2-h intervals (12, 14, 16, IX, 20, 22, 24, OZ, 04, 06, OX, and 10 hours). II was used analysis of variance for data adjustments, and the decomposition of the collected periods in non-orthogonal polynomial. It was observed a crescent linear effect of the T-4 plasma levels, presenting lower level of 49.60+/-11.41 and higher level of 76.99+/-10.0 ng/ml, at fourth and last blood samples collection, respectively. T-3 plasma levels showed a significant cubic response during 24 hours, with the highest value of 0.94+/-0.20 ng/ml at the end of the the study. In conclusion, thyroidal hormones levels were lower in the first blood samples collection, increasing progressively during the night, reaching the highest levels at the morning period.

Effect of amniotic membrane transplantation on corneal healing and proteoglycan expression in an experimental model of limbal deficiency in rabbits

PURPOSE. Amniotic membrane transplantation (AMT) has been used as a graft or as a dressing in ocular surface reconstruction, facilitating epithelization, maintaining normal epithelial phenotype, and reducing inflammation, vascularization, and scarring. The corneal transparency is due, at least in part, to the arrangement in orthogonal lamellae of collagen fibrils, surrounded by proteoglycans (PGs). These PGs regulate fibrilogenesis, the matrix assembly, and ultimately the corneal transparency. The purpose of the present study was to investigate the effects of AMT upon the corneal PGs after severe limbal injury.METHODS. Experiments were performed on the right corneas of 22 New Zealand female albino rabbits, and their left corneas were used as matched controls. These animals were divided into 3 groups: G1 (n = 10): total peritomy and keratolimbectomy, followed by application of 0.5 M NaOH; G2 (n = 10): submitted to the same trauma as G1, and treated by AMT; G3: no trauma, only AMT (n = 2). The right corneas of G2 and G3 were covered by DMSO 4 cryopreserved human amniotic membrane, fixed by interrupted 9-0 mononylon sutures, with its stromal face toward the ocular surface. After 7 or 30 days, the corneas were removed and PGs were extracted.RESULTS. Normal corneas contained approximately 9 mg of PGs per gram of dry tissue. AMT on intact cornea (G3) did not cause any changes in the concentration of PGs. In contrast, injured corneas contained much less PGs, both on the seventh and on the 30th day posttrauma. The PG concentration was even lower in injured corneas treated by AMT. This decrease was due almost exclusively to dermatan sulfate PGs, and the structure of dermatan sulfate was also modified, indicating changes in the biosynthesis patterns.CONCLUSIONS. Although beneficial effects have been observed on clinical observation and concentration of soluble proteins after AMT, the normal PG composition of cornea was not attained, even 30 days postinjury, indicating that the normal ocular surface reconstruction, if possible, is a long-term process. (Eur J Ophthalmol 2010; 20: 290-9)