Determinação de vazões extremas para diversos períodos de retorno para o Rio Paraguai utilizando métodos estatísticos

No presente trabalho foram analisadas as distribuições de probabilidade teórica Normal, Log-Normal, Exponencial, Gama e Weibull, para estimar as vazões máximas e mínimas anuais para o rio Paraguai, utilizando dados de uma estação fluviométrica localizado na cidade de Cáceres-MT. Os testes de Kolmogorov-Smirnov e Qui-Quadrado foram utilizados para verificar a aderência das probabilidades estimadas às freqüências observadas. A série utilizada compreende vazões máximas e mínimas anuais dos anos de 1966 a 2003, excluindo- se dados com falhas. Verificou-se que o melhor ajuste dos valores anuais de vazão máximas e mínimas são referentes a distribuição Gama e Weibull, respectivamente, conforme demonstrado pelo teste de Kolmogorov-Smirnov. Palavras-chave: Previsão de Vazão, teste de aderência.

Perfil de comercialização das Anonáceas nas Ceasas brasileiras

The anonas' quantity at Brazilian main terminal markets is growing and is concentrated at CEAGESP - 61%. SIEM's data has shown a large supply growth of atemoya and soursop, 35% and 32% respectively, and a sweetsop's decrease - 20%, from 2011 to 2012 at CEAGESP. Atemoya (54%), soursop (41%) and sweetsop (5%) are the most important anonnas at CEAGESP terminal market. The origin is concentrated in the state of Bahia - soursop and sweetsop and atemoya from Minas Gerais and São Paulo. The study of the value differentiation causes, comparing atemoya batches of the same grade size, of maximum and minimum value, at the same day, has shown the size homogeneity as the most important characteristic for value differentiation. The best strategy to promote the value differentiation for the grower is to improve size selection - its visual homogeneity.

Triplex Doppler Ultrassonography in Prenatal of Pregnant Bitches

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Análise da falha do suporte de mancal de um eixo cardan utilizado num veículo pesado

Pós-graduação em Engenharia Mecânica - FEG

Efeito da atividade física no uso de serviços de saúde na atenção primária no município de Rio Claro, SP

Introduction: Physical inactivity is identified as the fourth greatest risk factor of mortality worldwide. Little is known about how physical inactivity alters the demand for use of primary health care services, and it is a subject which demands further investigation. Objective: This study aims to determine the influence that physical activity has on the demand for use of primary health care services. Methods: This is a retrospective and cross-sectional study. The Rio Claro Active Health Program (SARC), studied in this research, is a partnership between the Municipal Health Foundation and Universidade Estadual Paulista Julio de Mesquita Filho (UNESP), represented by the Nucleus of Physical Activity, Sport and Health (NAFES) department of Physical Education and coordinated by Prof. Dr. Eduardo Kokubun. The study was carried out on residents of Rio Claro of both sexes seen at SARC. To assess the influence that physical activity had on the demand of the use of health services a questionnaire was given to participants who had attended the program since 2009. This questionnaire contains questions concerning the level of physical activity, health service use, number of both blood pressure and glucose measurement takings, number of spontaneous and scheduled medical visits, number of medications taken, number of illnesses and hospitalizations, comparing the data found in the previous year and the year after the program began. An informed term of consent was used for research participants. Descriptive analysis was carried out, using frequency, mean, maximum and minimum standard deviation. Results: Active participation in The Rio Claro Active Health program has positively influenced the following variables: perception of health, uncontrolled blood pressure, did not modify the number of diseases, number of medications in general, ...(Complete abstract click electronic access below)

Avaliação de momentos fletores em estruturas de fundação tipo radier em concreto armado

It aims the comparison of these moments between an analytical plates theory and a computational numerical simulation. It is accented the details of studies about analytical theory as well the process, step by step, of a program that has as an influence the method of finite elements. The theory of plates has an extremely importance when it is talked about slabs and it takes as a base some fundamental hypotheses (that the middle point of the plate is considered flat and under formable) the points that are normal in relation to the middle surface is not considered because of its intensity that is irrelevant in comparison to the rest. The computational programs offer good results when they are applied in a correct way and, it resolves numerous functions in a short period of time. The objective is to highlight the importance of bending moments, its points of maximum and minimum, that has the objective of realize a good reinforcement sizing for a reinforced concrete. Furthermore, it can propitiate an economy in places that is demanded a small quantity of steel, before dimensioned for a load that is distributed in all the surface of the plate, at the same intensity

Estimativa da altura por dimensões dentárias: uma revisão da literatura

The knowledge of Forensic Anthropology is very importance in cases of identification of human remains. One phase of this process is the study of human height, which can be accomplished with relative ease when intact corpses, complete skeletons or long bones are available. However, the experience of Forensic Dentistry is essential in situations in which there is only information of the skull or of the teeth. The objective of this study was to review in the literature and evaluate works concerning the estimate of the height calculated from dental dimensions. Carrea, in 1920, proposed the estimation of the probable height of an individual by developing formulas for maximum and minimum heights from measurements of the lower central and lateral incisors and canines. The method was used in the case "Josef Mengele", to complement estimates. Tested in the Brazilian population, 70% of match between the actual and the estimated stature were obtained. Using more precise instruments, in the modified method, 96% of correct matching were verified. Recently, a new formula was introduced to estimate height, from measurements of upper teeth, because the technique cannot be used when jaw is not available. The correlation between height and dental dimensions is demonstrated. However, there is still a lack in scientific literature in this field, and further studies are necessary. The estimate of height from dental dimensions can be very useful and important, especially in situations where the complete skeleton it not found, and long bones are not available.

Sazonalidade da dieta e hábitos alimentares do gavião-peneira (Elanus leucurus) em habitats agrícolas no sul do Brasil

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Produção de fitases por fermentação em estado sólido e imobilização das enzimas por srpay drying

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Computer graphics applied to anatomy: a study of two bio-cad modeling methods on finite element analysis of human edentulous hemi-mandible

Modeling is a step to perform a finite element analysis. Different methods of model construction are reported in literature, as the Bio-CAD modeling. The purpose of this study was to perform a model evaluation and application using two methods of Bio-CAD modeling from human edentulous hemi-mandible on the finite element analysis. From CT scans of dried human skull was reconstructed a stereolithographic model. Two methods of modeling were performed: STL conversion approach (Model 1) associated to STL simplification and reverse engineering approach (Model 2). For finite element analysis was used the action of lateral pterygoid muscle as loading condition to assess total displacement (D), equivalent von-Mises stress (VM) and maximum principal stress (MP). Two models presented differences on the geometry regarding surface number (1834 (model 1); 282 (model 2)). Were observed differences in finite element mesh regarding element number (30428 nodes/16683 elements (model 1); 15801 nodes/8410 elements (model 2). D, VM and MP stress areas presented similar distribution in two models. The values were different regarding maximum and minimum values of D (ranging 0-0.511 mm (model 1) and 0-0.544 mm (model 2), VM stress (6.36E-04-11.4 MPa (model 1) and 2.15E-04-14.7 MPa (model 2) and MP stress (-1.43-9.14 MPa (model 1) and -1.2-11.6 MPa (model 2). From two methods of Bio-CAD modeling, the reverse engineering presented better anatomical representation compared to the STL conversion approach. The models presented differences in the finite element mesh, total displacement and stress distribution.

Vibração incidente sobre o corpo inteiro do operador de trator agrícola ensaiado em pista de vibração com diferentes lastros, velocidades e pressões de inflação dos pneus

Pós-graduação em Agronomia (Energia na Agricultura) - FCA

Couve consorciada com sorgo e feijão-guandu na ocorrência de pulgões e insetos predadores

Pós-graduação em Agronomia (Entomologia Agrícola) - FCAV

Máximos e mínimos com proposta de aplicação para funções quadráticas

Pós-graduação em Matemática em Rede Nacional - IBILCE

Avaliação dos níveis de vibração no operador de um trator agrícola ensaiado em pista normatizada em diferentes velocidades de deslocamento

Pós-graduação em Agronomia (Energia na Agricultura) - FCA