Effects of copper vapor laser irradiation (λ = 510.6 nm) on the enamel and dentine of human teeth: An ultra-structural morphologic study

Objective: A morphological and ultra-structural study of copper vapor laser (λ = 510.6 nm) effects on enamel and dentine was performed to show the effects of this radiation. Methods: A total of 15 human molars were cut in half; 15 pieces were separated for irradiation on enamel and 15 for dentine. These two groups were further divided into five experimental groups, including a control group, comprised of three half-sections each, irradiated by a CVL laser with a power of 7 W, a repetition rate of 15,000 pulses/sec and exposed at 500, 600, and 800 msec and 1 sec irradiation times with a 5-sec interval between irradiations. Results: In an ultra-structural SEM exam, we observed that on the enamel surfaces irradiated for 1 sec there was morphological alteration that consisted of catering, flaking, and melting on the surfaces. There was no alteration for the other exposure times. On the dentine teeth irradiated for 1 sec, we observed an evident ultra-structural alteration of melted tissue and loss of morphological characteristics. In the dentine group irradiated by 800 msec, we observed ablation and a partial loss of morphological characteristics. In the dentine groups irradiated by 500 and 600 msec, no alteration was observed. Conclusions: The results showed that irradiation with CVL promoted morphologic changes in the enamel as well as in the dentine and demonstrated a need for future studies in order to establish a safe protocol for further use in the odontological practice.

Caracterização de Filmes a-C:H:Cl e a-C:H:Si:Cl produzidos por deposição à vapor químico assistido por plasma (PECVD) e deposição e implantação iônica por imersão em plasma (PIIID)

Pós-graduação em Ciência e Tecnologia de Materiais - FC

Treinamento básico sobre operação e segurança operacional de máquinas agrícolas

The study is intended to portray the experiment of mechanical engineering course academicians’ that work on health and labor security field, at the project “Primary Training of Operation and Operational Security of Agricultural Machines”, by practical and theoretical content for workers of a rural community, aiming operational security orientation on their work activities.

Avaliação do desempenho das máquinas agrícolas na implantação da cultura do girassol

The sunflower oleaginous is the fourth of recognized importance in the oil production and few studies related to agricultural operations adopted for this crop. The objective of the present work was to study the performance of agricultural machines in the conventional tillage and reduced in the plantation of the sunflower crop. The experiment was installed at the Experimental Farm of Lageado, belonging to the Faculty of Agricultural Sciences of UNESP, located in Botucatu-SP. It consisted of two types of tillage (conventional tillage-CC and reduced tillage-CR), with experimental design in randomized blocks and four replications. The treatment CC promoted less coverage of the soil surface protected with waste when compared to CR treatment. The chisel plow was the tillage of equipment that required the tractor higher average traction force, average power traction and slippage, consequently, promoted lower average speed of work. The theoretical field capacity and area of land involved in the treatment CR were superior when compared to treatment CC, thereby lower consumption of fuel per hour worked was lower in CR treatment.

Demanda energética de máquinas agrícolas na implantação da cultura do sorgo forrageiro

Forage sorghum can be grown in areas and environmental conditions dry and warm, where the productivity of other forage plants can often be uneconomical. The soil disturbance can be made only on the lines of planting (direct seeding) or entirely from the area for seeding (conventional tillage), as plowing, harrowing, subsoiling and chiseling (minimum tillage). The displacement speed ideal for planting is one in which the groove is opened and closed without removing the over-ground, allowing the distribution of seed spacing and depth constant. The experiment was conducted in a soil classified as Typic Oxisol at Lageado Experimental Farm, Faculty of Agronomic Sciences, UNESP, Botucatu campus. This study aimed to evaluate the response of sorghum in four forward speeds (3, 5, 6 and 9 km h-1) and four systems of soil management: SD (direct seeding), GP (harrow + sowing), LPG (disc harrow and two light disking + sowing) and CR (scarification and seeding). Data was subjected to analysis of variance in a factorial 4 x 4 and a randomized block design with split plots. The following parameters were determined: average speed, average strength of the drawbar, the average power drawbar, theoretical field capacity of the tractor-equipment, fuel consumption per hour. For the conditions under which the experiment was conducted, it was concluded that the hourly fuel consumption was not influenced by tillage systems and was inversely proportional to the increase of speed work, and that the change of speed in the sowing operation did not provide additional the values of average traction force on the bar of the tractor-planter.

Estimativa da irradiação solar global pelo método de Angstrom-Prescott e técnicas de aprendizado de máquinas

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Melhoria de eficiência de máquinas pela metodologia DMAIC em eventos Kaizen

In a highly competitive and globally integrated market, excellence in production processes has become a survival factor, instead of just a differential point. In this context, companies from various sectors have resorted to philosophies and techniques already established in the literature to improve the efficiency of their production processes. This paper discusses aspects and techniques used to improve the production efficiency of a multinational company that manufactures surgical devices to a global market. Through DMAIC methodology, there were found opportunities to improve machines' efficiency by OEE, an efficiency indicator, in Kaizen Events. A case study was conducted to analyze the methodology and to identify good practices and difficulties along the way

Implementação do OEE nas máquinas de laminação a frio

Through a description of the productivity problems experienced by some enterprises, to optimize their respective production lines, results of poor performance or low quality, the following work aims to explain and demonstrate the practical application of the theory of overall equipment effectiveness (OEE) on cold lamination machines in a steel industry . The project, to ensure your goal, is based on structuring a complete planning to increase levels of performance, availability and quality relating to rolling. On completion of the work, will be presented forecasts of future goals for the OEE, to search for continuous improvement and global standards of efficiency, taking into account, the sector the company operates, the history of the laminators, and financial aspects

Análise envoltória de dados combinada com a lógica fuzzy em problemas de avaliação de eficiência de máquinas de consumo: um estudo em empresa do segmento farmacêutico

The pharmaceutical industry was consolidated in Brazil in the 1930s, and since then has become increasingly competitive. Therefore the implementation of the Toyota Production System, which aims to lean production, has become common among companies in the segment. The main efficiency indicator currently used is the Overall Equipment Effectiveness (OEE). This paper intends to, using the fuzzy model DEA-BCC, analyze the efficiency of the production lines of a pharmaceutical company in the Paraíba Valley, compare the values obtained by the model with those calculated by the OEE, identify the most sensitive machines to variation in the data input and develop a ranking of effectiveness between the consumer machinery. After the development, it is shown that the accuracy of the relationship between the two methods is approximately 57% and the line considered the most effective by the Toyota Production System is not the same as the one found by this paper