Preparação e caracterização da casca de banana prata particulada para aplicação com reforço em compósito de matriz de PEAD

The waste, exaggerated and incorrect disposal of biomass are common practices in modern times where everything is disposable. However the growing concern with the nature and the environment compel man to give nobler destinations for these products through sustainability and recycling of waste. Banana peel is a residual biomass, which is not consumed. It generates tons of waste per week in São Paulo city. This trash is disposed in dumps and landfills, which could be reduced by using it as reinforcement in natural composites. The high density polyethylene (HDPE) is a polymer derived from the ethylene polymerization and is easily recycled. Which makes it a sustainable material. In the present work characteristics of the natural composite composed with banana peel and high-density polyethylene were studied. It was noted that removing the lignin present in the banana peel, the fiber introduces a significant improvement in thermal resistance. The preparation of composite was made with a ratio of 5% and 10% of reinforcement in comparison with polymeric matrix mass. Composites were thermally, mechanically and microscopically characterized. The addition of fiber in the polymer increased the mechanical strength of the composite. The fiber surface treatment with distilled water removed the amorphous material present in the fibers, improving significantly thermal stability and increasing crystallinity of the celullose. The addition of 5% fiber in mass to the polymer increased significantly the tensile strength and elasticity modulus for the composite. With 10% of fiber addiction there were also an improvement when compared with pure HDPE, but when compared with 5% composite the mechanical properties are slightly lower. This may be due to the fiber particle size, which are small and eventually become a hub of tension ... (Complete abstract click electronic access below)

Efeito do tratamento alcalino da fibra na resistência mecânica do compósito epóxi/capim-sapê

Due to growing concerns for reducing environmental damage caused by the use of non-renewable raw materials, there is a growing demand for research related to aggregate technology with environmental preservation. Thus, the use of non-renewable materials and less aggressive materials has been gaining attention. About composite materials, the exchange of synthetic fibers by natural fibers, especially vegetable fiber as reinforcement, has been increasing, due to its physical-chemical properties such as mechanical strength, nontoxic, low cost, low density, processing flexibility, non-abrasive to the process equipment, requiring simple surface treatments, etc. This objective was to process composites reinforced with long fibers of sapegrass in epoxy matrix and characterize the composites through mechanical tests. Three groups of composites were prepared according to the treatment received by the reinforcement: without treatment, alkali treatment at concentration of 5% w/v and alkali treatment at 10% w/v concentration. The materials were analyzed by tensile and flexural, and tests also optical microscopy and scanning electron microscopy (SEM). The results were statistically analyzed. As the main result, the alkali treatment of 5% in the sapegrass fibers increases the tensile and flexural strength, as a consequence of the improve adhesion between matrix and reinforcement

Avaliação dos efeitos ambientais nas propriedades do compósito de poliamida 6,6/fibras de carbono

This graduation work done study of polyamide 6.6/composite carbon fibres, since its processing, characterization of the main properties. Besides the influence of temperature, UV radiation, salt spray and moisture on the mechanical and viscoelastic behavior. To achieve this goal, the first composite was processed from the heat compression molding using known variables of the process and using the empirical method to find the best value for other parameters. The method processing molding was chosen because it common in composites processing in order to evaluate the influence of crystallinity of the properties that influence the mechanical and viscoelastic behavior laminates. From the obtained laminate specimens were evaluated in weathering, such as: in hygrothermal chamber, UV, salt spray and thermal shock. In another step, the effect produced by these constraints were evaluated by optical microscopy, ultrasound, dynamic mechanical analysis and vibration tests. This project was conducted at the Department of Technology and Materials of UNESP in Guaratingueta, where all the equipment and techniques for the implementation of this project met available. After the tests proved the applicability of the composite polyamide 6.6/carbon fibers in aeronautical applications with resistance the main climatic influences

Obtenção e caracterização térmica de compósitos nanoestruturados de resina fenol-furfurílica/CNT

Pós-graduação em Engenharia Mecânica - FEG

Estudo clínico longitudinal de dentes restaurados com sistemas cerâmicos livres de metal: estudo prospectivo sobre a hipersensibilidade dental pós-operatória

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Obtenção e caracterização de compósitos nanoestruturados de poli(sulfeto de fenileno) reforçados com nanotubos de carbono

Pós-graduação em Engenharia Mecânica - FEG

Fadiga em compósitos 5HS carbono/epóxi processados via RTM: relação entre cargas axiais no plano e modos de delaminação

Pós-graduação em Engenharia Mecânica - FEG

Otimização do processamento de partículas lead-free para aplicação em compósitos polímero/cerâmica com propriedades piezoelétrica e fotoluminescente

Pós-graduação em Química - IQ

O impacto do preparo, da cerâmica e do contato oclusal na distribuição de tensões em facetas

Pós-graduação em Odontologia Restauradora - ICT

Obtenção e caracterização de compósitos de benzoxazina/fibra de carbono

Pós-graduação em Engenharia Mecânica - FEG

Predição de vida em fadiga de compósitos estruturais baseado em análises dinâmico-mecânicas

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Reabilitação estética com enfoque nas diferentes cores de substratos e na escolha da cor do cimento adesivo

The evolution of techniques and materials applied to adhesive ceramic restorations resulted in the intensification of its use, proving to be an excellent method of aesthetic restoration. Some important features of this technique are its conservative preparation, which avoids an excessive loss of tooth structure and its high aesthetic value provided by the ceramic even when utilized under different color of dental substrates. The aim of this paper was to report a clinical case with full crowns, porcelain veneers and non-prep veneers, enhancing peculiarities related to the material used, tooth preparation techniques, cementing, indications and contraindications.

Recuperação da harmonia dos dentes anteriores por meio de implantes e restaurações cerâmicas

Introdução: a ausência ou alterações da estrutura dentária, principalmente em áreas estéticas, compromete a aparência, as relações sociais, a autoestima e, consequentemente, a qualidade de vida do indivíduo. Atualmente, avanços tecnológicos e científicos na Odontologia têm possibilitado várias opções de tratamentos reabilitadores e restauradores que oferecem resultados cada vez mais seguros e confiáveis. Objetivo: relatar, por meio de um caso clínico, a recuperação da harmonia dos dentes anteriores com a utilização de laminados de cerâmica e prótese sobre implante associada a recursos para recuperar a estética gengival. Conclusão: o planejamento adequado, associado aos conhecimentos de uma Odontologia integrada, possibilita resultados extremamente satisfatórios, resgatando a função e a estética, tanto dentária quanto gengival, proporcionando um sorriso harmonioso e o bem-estar social do paciente.

Estudo clínico retrospectivo de restaurações cerâmicas do tipo laminado sobre dentes com ou sem preparo dentário: 1 a 5 anos de acompanhamento

Pós-graduação em Odontologia - FOA

Estruturas de concreto reforçadas com PRFC parte II: análise dos modelos de cisalhamento

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)