Evaluation of recycled tiles and OSB ceiling materials in closed broiler house prototypes

This study aimed at evaluating the thermal performance of a modular ceiling system for poultry houses. The reduced- and distorted-scale prototypes used ceiling modules made of reforested wood and were covered with recycled long-life package tiles. The following parameters were measured for 21 days: tile internal surface temperature (ST), globe temperature and humidity index (WBGT), and radiant heat load (RHL). Measurements were made at times of highest heat load (11:00 am, 13:00 pm, and 03:00 pm). Collected data were analyzed by R statistics software. Means were compared by multiple comparison test (Tukey) and linear regression was performed, both at 5% significance level. The results showed that the prototype with the ceiling was more efficient to reduce internal tile surface temperature; however, this was not sufficient to provide a comfortable environment for broilers during the growout. Therefore, other techniques to provide proper cooling are required in addition to the ceiling.

Influência da cinética de oxidação no controle da atmosfera de fornos de revestimentos cerâmicos

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Processamento de cerâmicas reticuladas a partir de matérias-primas naturais

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Matéria-prima da formação Corumbataí na região do pólo cerâmico de Santa Gertrudes, SP, com características naturais para fabricação de argila expandida

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Estudo comparativo das argilas das olarias dos municípios de Alfenas e Areado, MG

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Reintegração dos finos provenientes do beneficiamento de argila no processo de produção de revestimentos via seca

Na região de Rio Claro (SP), localiza-se o Pólo Cerâmico de Santa Gertrudes, responsável por cerca de 50% da produção nacional de revestimentos. Durante o beneficiamento da argila e preparação da massa, cerca de 2 a 3% argila fina é colocada em suspensão no ar, sendo quase toda retida nos filtros de manga. Esse material fino, por problemas de homogeneização ou tecnológico, representa perda de material e se constitui em um potencial agente de contaminação do ar e da água, necessitando ser armazenado. A presente pesquisa buscou viabilizar o aproveitamento do pó retido nos filtros, no próprio processo, através da granulação da massa por aspersão de barbotina preparada com o pó. Investigaram-se a composição ideal da barbotina e a influência dessa metodologia no produto final, comparando a massa granulada por aspersão com a massa-padrão.

Propriedades reológicas de matérias-primas do Pólo Cerâmico de Santa Gertrudes provenientes da Formação Corumbataí (região de Rio Claro, SP)

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Programa de apoio à legalização mineral de olarias da região de Rio Claro (SP)

Esse artigo apresenta os resultados de um projeto denominado de Projeto Parceria, desenvolvido no período de 2007 a 2010, com objetivo de orientar, tecnicamente, os oleiros associados da ASCER, para a correta condução das atividades de extração de matéria-prima das jazidas utilizadas pela indústria oleira. As atividades desenvolvidas, nesse projeto, contemplam a legalização da situação minerária das atuais áreas de extração, orientação em relação à recuperação das áreas degradadas pela mineração e caracterização cerâmica dos materiais argilosos utilizados na produção de tijolos. Fizeram parte desse estudo quatorze Olarias situadas na região de Rio Claro (SP). A legalização das atividades de extração mineral, na área da jazida de cada olaria, conduziu, automaticamente, à legalização ambiental, que está sendo atualmente executada. Duas olarias não puderam regularizar as suas extrações, pois as áreas de suas propriedades estavam oneradas no DNPM. Outras duas olarias não possuíam documentações referentes à parte jurídica das empresas, necessárias para legalização de suas áreas. Os materiais argilosos utilizados pelos oleiros foram caracterizados quanto às suas aplicações cerâmicas como material nobre para a fabricação de telhas e tijolos, gerando produtos de alta qualidade.

Characterization of ceramic powders used in the inCeram systems to fixed dental Prosthesis

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Si3N4 ceramic cutting tool sintered with CeO2 and Al2O3 additives with AlCrN coating

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Demulsification of water/sunflower oil emulsions by a tangential filtration process using chemically impregnated ceramic tubes

A tangential filtration process was implemented in this study using porous ceramic tubes made of alpha-alumina produced by the slip-casting technique. These tubes were sintered at 1450 degrees C and characterized by mercury intrusion porosimetry, which revealed a mean pore size of 0.5 mu m. The tubes were chemically impregnated with a zirconium citrate solution, after which they were calcined and heat treated at temperatures of up to 600 and 900 degrees C to eliminate volatile organic compounds and transform the zirconium citrate into zirconium oxide impregnated in the alumina in the form of nanoparticle agglomerates. The microporous pipes were tested on a microfiltration hydraulic system to analyze their performance in the demulsification of sunflower oil and water mixtures. The fluid-dynamic parameters of Reynolds number and transmembrane pressure were varied in the process. The volume of permeate was analyzed by measuring the Total Organic Carbon concentration (TOC), which indicated 99% of oil phase retention. The emulsified mixture was characterized by optical microscopy, while the morphology and composition of the impregnated microporous tubes were analyzed by scanning electron microscopy (SEM). Quantification of the TOC values for the tube impregnated once at 600 degrees C showed the best demulsification performance, with the concentration on permeate smaller than 10 mg/L. The impregnated tube sintered once at 900 degrees C presented low carbon concentration (smaller than 20 mg/L), has the advantage of presenting the greatest trans-membrane flux in relation to the other microporous tube. (c) 2006 Elsevier B.V. All rights reserved.

Effect of aging on the stability of ceramic foams prepared by thermostimulated sol-gel process

This work presents a new route of preparation of zirconium ceramic foams based on the thermostimulated sol-gel process. This method produces gelled bodies with up to 90% of porosity in the wet gel and can be used to make complex-shaped components. Unfortunately, the shrinkage during the drying step allows to a catastrophic reduction (50%) of the foam porosity. To improve the foam stability we carried out a systematic study of the effect of gel foam aging on the drying process. Samples were aged in closed vessel at 25 C during different time period (from 6 to 240 h). The shrinkage and the mass loss during drying at 50 C were measured in situ, using a non-contact technique performed with a special apparatus. The results show that the total linear shrinkage decreases from 46% to 8% as the aging period increase from 6 to 240 h. This behavior is followed by a small change of total mass loss, from 42 to 54%. It indicates that by aging the structural stiffness of the foams increases due to secondary condensation reactions. Thus, by controlling the aging period, the porosity can be increased from 67 to 75% and the average size of mesopores of dried foams can be screened from 0.3 to 0.9 mum. Finally, these results demonstrate that the thermostimulated sol-gel transition provides a potential route to ceramic foams manufacture.

ac conductivity and conduction mechanism of NaNbO3 semiconductor antiferroelectric ceramic: A relaxational approach at high temperature

The electric properties of the sodium niobate perovskite ceramic were investigated by impedance spectroscopy in the frequency range from 5 Hz to 13 MHz and from room temperature up to 1073 K, in a thermal cycle. Both capacitance and conductivity exhibit an anomaly at around 600 K as a function of the temperature and frequency. The electric conductivity as a function of angular frequency sigma(omega) follows the relation sigma(omega)=Aomega(s). The values of the exponent s lie in the range 0.15less than or equal tosless than or equal to0.44. These results were discussed considering the conduction mechanism as being a type of polaron hopping. (C) 2003 American Institute of Physics.

Mechanochemical synthesis of ceramic powders with perovskite structure

The mechanical activation is one of the most effective method for obtaining highly disperse system due to mechanical action stress fields form in solids during milling procedure. This effect results in changes of free energy, leading to release of heat, formation of a new surface, formation of different crystal lattice defects and initiation of solid-state chemical reaction. The accumulated deformation energy determines irreversible changes of crystal structure and consequently microstructure resulting in the change of their properties. Mechanochemical processing route has been developed recently for the production of intermetallic and alloy compounds. The intrinsic advantage of this process is that the solid-state reaction is activated due to mechanical energy instead of the temperature. It was shown that the chemical reactivity of starting materials could be improved significantly after mechanochemical activation and, subsequently, the calcination temperature was reduced. Besides, it was apparent that the mechanochemical treatment could enhance the reactivity of constituent oxides; however, the sintering process could not be avoided to develop the desired ceramics. A novel mechanochemical technique for synthesis of fine-grained perovskite structured powders has shown that it is possible to form perovskite at room temperature. The effect of milling on the formation of perovskite structure of barium titanate (BT), lead titanate (PT), PZT, PZN, magnesium niobate (PMN) and LM ceramic materials was analyzed. The dielectric properties of sintered ceramics are comparable with those prepared by other methods in the literature. (C) 2003 Elsevier B.V. B.V. All rights reserved.