Different responses in bulk density and saturated hydraulic conductivity to soil deformation by logging machinery on a Ferralsol under native forest

Ferralsols have high structural stability, although structural degradation has been observed to result from forest to tillage or pasture conversion. An experimental series of forest skidder passes in an east Amazonian natural forest was performed for testing the effects of mechanical stress during selective logging operations on a clay-rich Ferralsol under both dry and wet soil conditions. Distinct ruts formed up to 25 cm depth only under wet conditions. After nine passes the initially very low surface bulk density of between 0.69 and 0.80 g cm(-3) increased to 1.05 g cm(-3) in the wet soil and 0.92 g cm(-3) in the dry soil. Saturated hydraulic conductivities, initially > 250 mm h(-1), declined to a minimum of around 10 mm h(-1) in the wet soil after the first pass, and in the dry soil more gradually after nine passes. The contrasting response of bulk density and saturated hydraulic conductivity is explained by exposure of subsoil material at the base of the ruts where macrostructure rapidly deteriorated under wet conditions. We attribute the resultant moderately high hydraulic conductivities to the formation of stable microaggregates with fine sand to coarse silt textures. We conclude that the topsoil macrostructure of Ferralsols is subject to similar deterioration to that of Luvisols in temperate zones. The stable microstructure prevents marked compaction and decrease in hydraulic conductivity under wetter and more plastic soil conditions. However, typical tropical storms may regularly exceed the infiltration capacity of the deformed soils. In the deeper ruts water may concentrate and cause surface run-off, even in gently sloping areas. To avoid soil erosion, logging operations in sloping areas should therefore be restricted to dry soil conditions when rut formation is minimal.

Aging behaviour of 25Cr-17Mn high nitrogen duplex stainless steel

The precipitation behaviour of a nickel free stainless steel containing 25% chromium, 17% manganese and 0.54% nitrogen, with duplex ferritic-austenitic microstructure, was studied using several complementary techniques of microstructural analysis after aging heat treatments between 600 and 1 000 degrees C for periods of lime between 15 and 6 000 min. During aging heat treatments, ferrite was decomposed into sigma phase and austenite by a eutectoid reaction, like in the Fe-Cr-Ni duplex stainless steel. Chromium nitride precipitation occurred in austenite, which had a high nitrogen supersaturation. Some peculiar aspects were observed in this austenite during its phase transformations. Chromium nitride precipitation occurred discontinuously in a lamellar morphology, such as pearlite in carbon steels. This kind of precipitation is not an ordinary observation in duplex stainless steels and the high levels of nitrogen in austenite can induce this type of precipitation, which has not been previously reported in duplex stainless steels. After chromium nitride precipitation in austenite, it was also observed sigma phase formation near the cells or colonies of discontinuously precipitated chromium nitride. Sigma phase formation was made possible by the depletion of nitrogen in those regions. Time-temperature-transformation (precipitation) diagrams were determined.

Q-ANALOG REALIZATION OF NUCLEON PAIRING

A q-deformed analogue of zero-coupled nucleon pair states is constructed and the possibility of accounting for pairing correlations examined. For the single orbit case, the deformed pairs are found to be more strongly bound than the pairs with zero deformation, when a real-valued q parameter is used. It is found that an appropriately scaled deformation parameter reproduces the empirical few nucleon binding energies for nucleons in the 1f7/2 orbit and 1g9/2 orbit. The deformed pair Hamiltonian apparently accounts for many-body correlations, the strength of higher-order force terms being determined by the deformation parameter q. An extension to the multishell case, with deformed zero-coupled pairs distributed over several single particle orbits, has been realized. An analysis of calculated and experimental ground state energies and the energy spectra of three lowermost 0+ states, for even-A Ca isotopes, reveals that the deformation simulates the effective residual interaction to a large extent.

MANY-BODY PROBLEMS WITH COMPOSITE-PARTICLES AND Q-HEISENBERG ALGEBRAS

We propose to employ deformed commutation relations to treat many-body problems of composite particles. The deformation parameter is interpreted as a measure of the effects of the statistics of the internal degrees of freedom of the composite particles. A simple application of the method is made for the case of a gas of composite bosons.

The Serido Group of NE Brazil, a late Neoproterozoic pre- to syn-collisional basin in West Gondwana: insights from SHRIMP U-Pb detrital zircon ages and Sm-Nd crustal residence (T-DM) ages

The Serido Group is a deformed and metamorphosed metasedimentary sequence that overlies early Paleoproterozoic to Archean basement of the Rio Grande do Norte domain in the Borborema Province of NE Brazil. The age of the Serido Group has been disputed over the past two decades, with preferred sedimentation ages being either Paleoproterozoic or Neoproterozoic. Most samples of the Serido Formation, the upper part of the Serido Group, have Sm-Nd T-DM ages between 1200 and 1600 Ma. Most samples of the Jucurutu Formation, the lower part of the Serido Group, have T-DM ages ranging from 1500 to 1600 Ma; some basal units have T-DM ages as old as 2600 Ma, reflecting proximal basement. Thus, based on Sm-Nd data, most, if not all, of the Serido Group was deposited after 1600 Ma and upper parts must be younger than 1200 Ma.Cathodoluminescence photos of detrital zircons show very small to no overgrowths produced during ca. 600 Ma Brasiliano deformation and metamorphism, so that SHRIMP and isotope dilution U-Pb ages must represent crystallization ages of the detrital zircons. Zircons from meta-arkose near the base of the Jucurutu Formation yield two groups of ages: ca. 2200 Ma and ca. 1800 Ma. In contrast, zircons from a metasedimentary gneiss higher in the Jucurutu Formation yield much younger ages, with clusters at ca. 1000 Ma and ca. 650 Ma. Zircons from metasedimentary and metatuffaceous units in the Serido Formation also yield ages primarily between 1000 and 650 Ma, with clusters at 950-1000, 800, 750, and 650 Ma. Thus, most, if not all, of the Serido Group must be younger than 650 Ma. Because these units were deformed and metamorphosed in the ca. 600 Ma Brasiliano fold belt during assembly of West Gondwana, deposition probably occurred ca. 610-650 Ma, soon after crystallization of the youngest population of zircons and before or during the onset of Brasiliano deformation.The Serido Group was deposited upon Paleoproterozoic basement in a basin receiving detritus from a variety of sources. The Jucurutu Formation includes some basal volcanic rocks and initially received detritus from proximal 2.2-2.0 Ga (Transamazonian) to late Paleoproterozoic (1.8-1.7 Ga) basement. Provenance for the upper Jucurutu Formation and all of the Serido Formation was dominated by more distal and younger sources ranging in age from 1000 to 650 Ma. We suggest that the Serido basin may have developed as the result of late Neoproterozoic extension of a pre-existing continental basement, with formation of small marine basins that were largely floored by cratonic basement (subjacent oceanic crust has not yet been found). Immature sediment was initially derived from surrounding land; as the basin evolved much of the detritus probably came from highlands to the south (present coordinates). Alternatively, if the Patos shear zone is a major terrane boundary, the basin may have formed as an early collisional foredeep associated with south-dipping subduction. In any case, within 30 million years the region was compressed, deformed, and metamorphosed during final assembly of West Gondwana and formation of the Brasiliano-Pan African fold belts. (C) 2003 Elsevier B.V. All rights reserved.

THE PHYSICAL CONTENT OF THE SP(1,R) MODEL

We analyse the properties of the Sp(1, R) model states using a basis obtained from the deformed harmonic oscillator wavefunctions. We make an Sp(1, R) calculation for C-12 and consider bases obtained from oblate, triaxial and prolate intrinsic states. The model states are given by angular momentum projection of vibrational phonons, which are associated with giant monopole and quadrupole resonances.

A new method for extending the range of conductive polymer sensors for contact force

This paper describes a technique for extending the force range of thin conductive polymer force sensors used for measuring contact force. These sensors are conventionally used for measuring force by changing electrical resistance when they are compressed. The new method involves measuring change in electrical resistance when the flexible sensor, which is sensitive to both compression and bending, is sandwiched between two layers of spring steel, and the structure is supported on a thin metal ring. When external force is applied, the stiffened sensor inside the spring steel is deformed within the annular center of the ring, causing the sensor to bend in proportion to the applied force. This method effectively increases the usable force range, while adding little in the way of thickness and weight. Average error for loads between 10 N and 100 N was 2.2 N (SD = 1.7) for a conventional conductive polymer sensor, and 0.9 N (SD = 0.4) using the new approach. Although this method permits measurement of greater loads with an error less than 1 N, it is limited since the modified sensor is insensitive to loads less than 5 N. These modified sensors are nevertheless useful for directly measuring normal force applied against handles and tools and other situations involving forceful manual work activities, such as grasp, push, pull, or press that could not otherwise be measured in actual work situations.

Coffee leaf scorch caused by a strain of Xylella fastidiosa from citrus

Citrus variegated chlorosis (CVC) and coffee leaf scorch (CLS) are two economically important diseases in Brazil caused by the bacterium Xylella fastidiosa. Strains of the bacterium isolated from the two plant hosts are very closely related, and the two diseases share sharpshooter insect vectors. In order to determine if citrus strains of X. fastidiosa could infect coffee and induce CLS disease, plant inoculations were performed. Plants of coffee, Coffea arabica 'Mundo Novo', grafted on Coffea canephora var, robusta 'Apuatao 2258' were mechanically inoculated with triply cloned strains of X. fastidiosa isolated from diseased coffee and citrus. Three months postinoculation, 5 of the 10 plants inoculated with CLS-X. fastidiosa and 1 of the 10 plants inoculated with CVC-X. fastidiosa gave positive enzyme-linked immunosorbent assay (ELISA) and/or polymerase chain reaction (PCR). Eight months postinoculation, another six plants inoculated with CVC-X. fastidiosa gave positive PCR results. The two X. fastidiosa strains were isolated from the inoculated plants and showed the same characteristics as the original clones by microscopy, ELISA, and PCR. None of the plants inoculated with sterile periwinkle wilt (PW) medium as controls gave positive reactions in diagnostic tests, and none developed disease symptoms. Six months postinoculation, seven plants inoculated with CLS-X. fastidiosn and eight inoculated with CVC-X. fastidiosa began to develop characteristic CLS symptoms, including apical and marginal leaf scorch, defoliation, and reductions of internode length, leaf size, and plant height, terminal clusters of small chlorotic and deformed leaves, and lateral shoot dieback. We have demonstrated that X, fastidiosa from citrus plants is pathogenic for coffee plants. This has important consequences for the management of CLS disease and has implications for the origin of citrus variegated chlorosis disease.

Plasma nitriding of sintered AISI 316L at several temperatures

Samples of sintered AISI 316L stainless steel were plasma nitrided in a mixture of H-2-20% N-2, for 3 or 4 h. The treatment temperature was selected in 400-550 degreesC interval, in steps of 50 degreesC. X-ray diffraction (glancing angle geometry-GAXRD), conversion electron Mossbauer spectroscopy (CEMS), optical microscopy and Vickers microhardness were used as analytical techniques. For T greater than or equal to 500 degreesC and t = 4 h, a 40-mum layer is formed. The GAXRD results showed a transformation of the austenite gamma phase to the martensite in the sinterization process and showed as well, that the gamma' (Fe4N) phase is the predominant nitride besides small amounts of epsilon-Fe2N, gamma(N) CrN, Cr2O3 and the fcc nitrogen supersatured solid phase gamma(N). The CrN phase seems to decrease with temperature while the gamma(N) phase fraction is almost less than or equal to10%, independently on the temperature. The CEMS results indicated that while the gamma(N) fraction decreases with temperature of plasma nitriding, the gamma' fraction increases proportionally. (C) 2003 Elsevier B.V. All rights reserved.

Induction of the split sting trait in Africanized Apis mellifera (Hymenoptera : Apidae) by cold treatment of pupae

Split sting is the name given to a nonfunctional honey bee sting characterized by lancets not attached to the stylet. It has appeared in a mutant line in Brazil, and has provoked interest as a possible means to reduce honey bee colony defensiveness. We induced this alteration in Africanized Apis mellifera L. workers and queens by maintaining pupae at 20 degrees C. In particular, we determined the pupal phase most susceptible to alterations in the sting caused by cold treatment, and we investigated whether this treatment also affected survival to the adult phase and wing morphology. The highest frequency of split sting was detected in workers treated at the pink-eyed pupal phase. The lowest frequency was observed in the bees treated at the oldest worker pupal phase studied (brown-eyed pupae with lightly pigmented cuticle). Both queen pupal phases tested (white and pink-eyed pupae) were equally sensitive and produced high percentages of adults with split sting. However, the 20 degrees C treatment of workers and queens, at the different pupal phases, resulted in high frequencies of adults with deformed wings. Also, fewer workers and queens treated at the earlier pupal stages reached adult emergence. There was also an arrest in developmental time, corresponding to the period of cold treatment.

First record of petrified Permian pecopterids from the Parana Basin, Brazil (Corumbatai Formation, Passa Dois Group, northeastern State of São Paulo): Morphology, anatomy and paleoecological implications

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Effects of milling condition on the surface integrity of hot forged steel

This paper presents a study on the influence of milling condition on workpiece surface integrity focusing on hardness and roughness. The experimental work was carried out on a CNC machining center considering roughing and finishing operations. A 25 mm diameter endmill with two cemented carbide inserts coated with TiN layer were used for end milling operation. Low carbon alloyed steel Cr-Mo forged at 1200 degrees C was used as workpiece on the tests. Two kinds of workpiece conditions were considered, i.e. cur cooled after hot forging and normalized at 950 degrees C for 2 h. The results showed that finishing operation was able to significantly decrease the roughness by at least 46% without changing the hardness. on the other hand, roughing operation caused an increase in hardness statistically significant by about 6%. The machined surface presented deformed regions within feed marks, which directly affected the roughness. Surface finish behavior seems to correlate to the chip ratio given the decrease of 25% for roughing condition, which damaged the chip formation. The material removal rate for finishing operation 41% greater than roughing condition demonstrated to be favorable to the heat dissipation and minimized the effect on material hardness.

Carbon Stocks and Isotopic Composition of the Organic Matter in Soils Covered by Native Vegetation and Pasture in Sorocaba, SP, Brazil

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Tensor3D: A computer graphics program to simulate 3D real-time deformation and visualization of geometric bodies

Tensor3D is a geometric modeling program with the capacity to simulate and visualize in real-time the deformation, specified through a tensor matrix and applied to triangulated models representing geological bodies. 3D visualization allows the study of deformational processes that are traditionally conducted in 2D, such as simple and pure shears. Besides geometric objects that are immediately available in the program window, the program can read other models from disk, thus being able to import objects created with different open-source or proprietary programs. A strain ellipsoid and a bounding box are simultaneously shown and instantly deformed with the main object. The principal axes of strain are visualized as well to provide graphical information about the orientation of the tensor's normal components. The deformed models can also be saved, retrieved later and deformed again, in order to study different steps of progressive strain, or to make this data available to other programs. The shape of stress ellipsoids and the corresponding Mohr circles defined by any stress tensor can also be represented. The application was written using the Visualization ToolKit, a powerful scientific visualization library in the public domain. This development choice, allied to the use of the Tcl/Tk programming language, which is independent on the host computational platform, makes the program a useful tool for the study of geometric deformations directly in three dimensions in teaching as well as research activities. (C) 2007 Elsevier Ltd. All rights reserved.

On the Milnor fibre and L numbers of semi-weighted homogeneous arrangements

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)