Theoretical and experimental study of agricultural spraying using CFD

This paper presents a computational fluid dynamics (CFD) application about the axial fan design used in an agricultural spraying system with a theoretical and experimental analysis of comparative results between the characteristic curves of a fan for several rotations and numerical results for the influence of blade attack angle variation and optimization of the spraying system, both for a same rotation. Flow was considered three-dimensional, turbulent, isothermal, viscous and non-compressible in a steady state, disregarding any influence of the gravity field. The average turbulent field was obtained from the application of time average where the turbulence model required for closing the set of equations was the k-E model. Resolution of all connected phenomena was achieved with the help of a fluid dynamics computer, CFX, which uses the finite volumes technique as a numerical method. In order to validate the theoretical analysis, an experiment was conducted in a circular section of a horizontal wind tunnel, using a Pitot tube for pressure readings. The main results demonstrate that the methodology used, based on CFD techniques, is able to reproduce the phenomenological behavior of an axial fan in a spraying system because results were very reliable and similar to experimentally measured ones.

Cardiovascular and respiratory evaluation during cervical myelography using ioversol in dogs

The objective of this study was to evaluate cardiovascular and respiratory effects associated with neck flexion, subarachnoid puncture, cerebrospinal fluid drainage and the subarachnoid infusion of ioversol (320mgl/mL) in dogs under isoflurane general anesthesia. The dogs received infusion of: autologous cerebrospinal fluid at 38 degrees C (GC - control group); ioversol 0.3mL/ Kg at 25 degrees C (GI25) and heated to 38 degrees C (GI38). Heart rate, systolic and diastolic arterial pressure, respiratory rate, oxyhemoglobin saturation and electrocardiography readings were recorded. The results showed that cervical myelography with ioversol 320mgl/mL at 0.3mL/Kg (25 C-degrees and 38C degrees) did not significantly alter recorded parameters, except for an elevation in arterial pressure.

Long-term surface hardness and monomer conversion of a nonofilled and a microhybrid composite resin

Objective: This study aims to evaluate the degree of conversion (DC) and hydrolytic degradation through the Vickers hardness test (HV) of a nanofilled (Filtek™ Z-250, 3M) and a microhybrid (Filtek™Supreme-XT, 3M) composite resin. Materials and methods: Eight disk-shaped specimens (4 mm diameter × 2 mm thick, ISO 4049) of each material were prepared for each test. Composites were inserted into single increment in a metallic matrix and light-cured for 40 seconds. VH readings were performed for each specimen at predetermined intervals: immediately after polymerization (control), 1, 2, 3, 7, 14, 21, 30 and 180 days. After curing, initial hardness measurements were performed and the specimens were immersed in artificial saliva at 37°C. For DC (%), specimens were ground, pressed with KBr and analyzed by FT-IR spectrophotometer. Results: Student t-test showed that there was no difference between the resins for DC (p = 0.252). ANOVA analysis revealed that Z-250 VH means were all greater than S-XT, for both top and bottom surfaces, whatever the storage-period in artificial saliva (p < 0.001). After 180 days of storage, the hardness obtained for S-XT was similar with that at the baseline, for both top and bottom surfaces. While for Z-250 hardness was not significantly different from baseline only for top surface, but there was a significant decrease observed in hardness for bottom surface. Conclusion: The materials tested showed no evidence of hydrolytic degradation in a significant way, in a 6-month storagetime in artificial saliva. Nanofilled resin presents a monomer conversion comparable to the conventional microhybrid.

Color stability of a nanofilled resin: influence of polishing and finishing and fluoride solutions according to time

Aim: The aim of the study was evaluate the finishing and polishing effect of the color stability of the composite resin Filtek Supreme XT, according to different fluoride solutions and time. Material and Methods: Specimens were prepared (n=140) with half of the samples finished and polished. The experimental groups were divided according to the presence or absence of finishing and polishing and immersion solutions (artificial saliva, sodium fluoride solution at 0.05% - manipulated, Fluordent Reach, Oral B, Fluorgard). The specimens remained in artificial saliva for 24 hours and were subjected to an initial color analysis using a spectrophotometer CIELab system. Then, they were immersed in the experimental solutions for 1 minute a day. The readings of the color change were made after 24 and 48 hours, 7, 14, 21, 30 and 60 days after the first immersion. The three-way mixed Analysis of Variance (ANOVA) ("finishing/polishing", "immersion medium" and “time”) were performed. For multiple comparisons, the Sidak test for repeated measure was used, with a 5% level of significance. Results: The finishing and polishing factor showed significant variability, independently of the immersion media (p<0.001). Cconclusion: Finishing and polishing procedures yielded better color stability to composite resin over time, regardless of the immersion media.

Effect of thermal and mechanical cycles on the hardness and roughness of artificial teeth

In this study the effects of thermal and mechanical cycles on the hardness and roughness of artificial teeth were evaluated. Materials and Methods:Specimens were prepared and stored in distilled water at 37ºC for 48 hours (n=10).The hardness and roughness readings were made in the following time intervals, according to each group:G1: after specimen storage in distilled water at 37°C for 48 hours; G2: after 600.000 constant mechanical cycles; G3: after 1.200.000 constant mechanical cycles; G4: after 2.500 thermalcycling baths, alternated between hot water (55°C) and cold water (5°C) and G5: after 5.000 thermalcycling baths, alternated between hot water (55°C) and cold water (5°C). After cycling and storage procedures, the specimens of each group were submittedto surface roughness and hardness readouts. Statistical evaluation was performed by three-way analysis of variance, complemented by the Tukey multiple comparisons of means test. The level of significance adopted was 5%. There was no significant difference between G1, G4 and G5 as regards mean roughness of different brands of artificial teeth. Groups G2 and G3 showed higher mean roughness values, and generally equivalent values in all time intervals, except for Trilux (G3> G2). Significant differences in hardness values were observed in different brands of artificial teeth, and differences in values after thermal and mechanical cycling. In conclusion, our findings suggest that thermal cyclingdid not change the roughness of the artificial teeth tested, but after the mechanical cycling the roughness values increased. Thermal and mechanical cycling influenced the hardness of the artificial teeth tested.

Evaluation of roof slope and exposure with different roofing materials in reduced models of animal production facilities in spring and summer

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Ra-226 and Ra-228 in mineral waters of southeast Brazil

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Hemoculture and polymerase chain reaction using primers TCZ1/TCZ2 for the diagnosis of canine and feline trypanosomiasis

Introduction. American trypanosomiasis, also known as Chagas disease, is a zoonosis caused by Trypanosoma cruzi (T. cruzi). Dogs and cats participate actively in this parasite's transmission cycle. This study aimed at evaluating the occurrence of T. cruzi in dogs and cats from Botucatu, SP, Brazil, as well as at evaluating the technique of hemoculture in LIT (liver infusion tryptose) medium by polymerase chain reaction (PCR). Methods. Blood samples were collected from 50 dogs and 50 cats in Botucatu-SP, Brazil. For hemoculture, the samples were inoculated in LIT medium, and readings were performed for four months. Upon completion of such period, all the hemocultures were processed for parasitic DNA extraction. The PCR reactions were performed by using primers TCZ1/TCZ2. Results. Ten dogs and ten cats (20%) were positive to PCR, and four dogs and three cats (7%) were positive to hemoculture. Only in a one cat sample (1%) there was confirmation of positive hemoculture by PCR for T. cruzi. Conclusions. Results showed that PCR was a suitable tool for the confirmation of the parasite detection in hemoculture samples, and that dogs and cats from Botucatu, SP, Brazil, are maintaining the role of household reservoirs of T. cruzi, which reinforces the need for constant epidemiologic surveillance for this zoonosis.

Glucose,cholesterol,total proteins and insulin-like growth factor typeI values in the follicular fluid of female river buffaloes (Bubalus bubalis)

Twenty six Murrah female river buffaloes, between 45 and 70 d post-partum, empty, multiparae, with an average live weight of 675 ± 56 kg, and average body condition of 3.5 points, in a 1 to 5 scale, were used to determine the concentrations of glucose, cholesterol, total protein and insulin-like growth factor type I(IGF-I) in the follicular fluid. The fluid was collected from dominant follicles, with diameters between 8 and 12 mm, by in vivo follicular aspiration. The oestrous cycle stage was not taken into account. The wave of follicular development was synchronized six days prior to the collection. Biochemical analyses of glucose and cholesterol were performed by the enzymatic colorimetric method with the utilization of commercial kits of Glicose (GOD-PAP) and Cholesterol (CHOD-PAP) (Kovalent), respectively. For the determination of total protein, the commercial kit total Protein (Kovalent), method Biuret, was employed. Readings were carried out through absorption spectrophotometry with visible light. Through the radioimmunoanalysis (RIA) technique the concentration of IGF-I was obtained using commercial kits of IRMA IGF-I (IMMUNOTECH). Descriptive statistics was used, by applying the PROC MEANS procedure of the SAS (2009) statistical package. Glucose concentrations (4.0 ± 0.75 mmol/L) and IGF-I (340 ± 129.83 ng/mL) showed higher values in female river buffaloes and dairy cows regarding those reported in other studies. However, cholesterol levels (0.51 ± 0.12 mmol/L) and total proteins (58.4 ± 4.43 g/L) were lower. Results indicate that there is a relationship between the concentration of biochemical indicators, the nutritional aspects, the diameter of the aspired follicles and the productive period.