Estudo teórico da contribuição à dose de partículas secundárias geradas por prótons de energias entre 100 e 200 MeV num Phantom de substituto de tecido MS20

The goal of this project is the reproduction, through the simulation code based on the MCNPX (Monte Carlo N-Particle eXtended) v2.50 method, of the proton beam interaction with the material, since, in proton therapy, only the particle ionization and excitation are analyzed and the occurence of nuclear interactive inelastic process are not considered. This work will help the development of studies concerning the contribution to the total dosis of secondary particles generated by nuclear interaction in proton therapy. They are: alpha particles ( ), deuterium(2H), tritium (3H), neutron (n) and helium (3He). A MS20 tissue substitute phantom was used as the target and the energy of the proton beams was within an interest range of 100 to 200MeV. With the results obtained, it was possible to generate graphics which allows the analysis of the dosis deposition relation with and without nuclear interaction, the percentage of secondary particles deposited dosis, the radial dispersion of neutrons in the material, the secondary particles multiplicity, as well as the relation between the secondary particles spectrum with the próton generated spectrum

Uma revisão sobre a resina uréia-formadeído (RUF) empregada na produção de painéis de madeira reconstituída

According to ABIPA (2009), Brazil is currently among the major producers of reconstituted wood panels, with one of the main factors for this condition, its climate and its large land area, which allows the cultivation of forests, which provide raw materials for these industries. To establish that market as power, Brazil has invested about R$ 1.3 billion in the last 10 years, yet designed an investment of 0.8 billion dollars over the next three years (BNDES, 2008). With the new investments in this segment, we expect a growth of about 66% in the resin consumption of urea-formaldehyde (GPC, 2009) which should also result in major investments by the companies producing this polymer. Currently employees are mainly three types of resins in the production industry panels, as follows: Urea-Formaldehyde Resin (R-UF), melamine-formaldehyde resin (R-MF) and Phenol-Formaldehyde Resin (R-FF). Especially the cost factor, the urea-formaldehyde resin is the most used by companies producing reconstituted wood panels. The UF-R is a polymer obtained by condensation of urea and formaldehyde reactors (usually batch type), characterized by being a thermosetting polymer which makes it very efficient for bonding wood composites. The urea-formaldehyde polymer, to present a quite complex, it becomes very difficult to predict the exact chain resulting in the process of condensation of urea with formaldehyde, so that a greater knowledge of its characteristics and methods for their characterization can result in greater control in industrial processes and subsequent decrease cost and improve the quality of reconstituted wood panels produced in Brazil

Estudo de melhorias dos painéis de baixa tensão da Faculdade de Engenharia de Guaratinguetá - UNESP

The protection and distribution systems for the electrics equipments are really important for the safety of products, process and final users, for an enterprise or even for a residence. For that, it’s necessary the utilization of low voltage switchboards for controlling the feeding of a charge, avoiding any kind of abnormality that can eventually occur. It’s necessary to pay attention in the cubicles conditions, and always verify if they are in accordance to the norms of the product, verifying also any kind of physical damage for the operator and/or users. In this line, the present graduation work analyses the low voltage switchboards in the college, checking if they are attending the actual standards, suggesting some improvements and later making a simulation of the creation of a new panel that reach all the needing in substitution of this actual, through the software Simaris. Using the research and lecture of norms and regulations for verifying the problems, this way we could register the greatest acting failures. These actions are made for becoming aware to the university about the danger in using electrics equipments without a minimum degree of protection, allowed by the law, and attempting to the urgency in changing this fails

Desenvolvimento de solução para o problema de alocação de navios em berços de terminais portuários: aplicação de algoritmos genéticos e otimização por nuvens de partículas

This work proposes two optimization algorithms for the solution of the Berth Allocation Problem (PAB). Due to the economic development of the country, it became necessary for the improvement of means of transport, which mainly shipping. For this, you need a better system management port, you will receive a lot of ships carrying cargo. In this work the PAB is approached so that the goals are to reduce costs and time handling in ports. For this, we applied two computational techniques, genetic algorithms and optimization for cloud particles, to obtain the best results for this problem. The results obtained with each type of algorithm are compared to conclude which method is more efficient for the port system

Estudo teórico da contribuição a dose de partículas secundárias geradas por prótons de energias entre 100-200 MeV num phantom de músculo estriado

In the treatment plans in conventional Proton therapy are considered only the elastic interactions of protons with electrons and/or nuclei, it means, mainly ionization and coulomb excitation processes. As the energy needed to reach the deep tumors should be of several hundred of MeVs, certainly the nuclear inelastic channels are open. Only some previous studies of the contribution of these processes in the full dose have been made towards targets composed of water. In this study will be presented the results of the simulation of the processes of interaction of beams of protons in the range of 100-200 MeV of energy with a cylindrical phantom composed by striated muscle (ICRU), emphasizing in the contribution to total dose due to the deposition of energy by secondary particles alpha (α), deuterium (2H), tritium (3H), neutron (n) and hélio3 (3He), originated by nuclear inelastic processes. The simulations were performed by using the method of Monte Carlo, via the computer code MCNPX v2.50 (Monte Carlo N-Particle eXtended). The results will be shown demonstrated through the graphics of the deposited dose with or without nuclear interaction, the percentual of dose deposited by secondary particles, the radial dispersion of neutrons, as well as the multiplicity of secondary particles

Análise das propriedades físico-mecânicas de painel particulado de eucalipto composto por três camadas com duas variações de pressão

The research aimed to produce sheets of particles with waste processing of Eucalyptus sp bonded with urea-formaldehyde and evaluate the effect of pressure variation in the quality of the boards produced. To do so, the Boards made were divided into two treatments depending on the pressing pressure of 30 to 40 kgf / cm². Once pressings, climatized, the particleboards have been sectioned in test samples, and underwent physical-mechanical tests for determining density, swelling and water absorption, modulus of rupture and elasticity in static bending and internal linking. The particleboards pressed at 40 kgf / cm ² showed the best results

Estudo teórico da contribuição à dose de partículas secundárias geradas por Prótons de energias entre 100 e 200 MeV num Phantom de osso cortical

In proton therapy, the deposition of secondary particles energy originated by nuclear inelastic process (n, 2H, 3H, 3He and α) has a contribution in the total dose that deserves to be discussed. In calculations of plans implemented for routine treatment, the paid dose is calculated whereas the proton loses energy by ionization and or coulomb excitement. The contribution of inelastic processes associated with nuclear reactions is not considered. There are only estimates for pure materials or simple composition (water, for example), because of the difficulty of processing targets consisting of different materials. For this project, we use the Monte Carlo method employing the code MCNPX v2.50 (Monte Carlo N-Particle eXtended) to present results of the contribution to the total dose of secondary particles. In this work, it was implemented a cylindrical phantom composed by cortical bone, for proton beams between 100 and 200 MeV. With the results obtained, it was possible to generate graphics to analyze: the dose deposition relation with and without nuclear interaction, the multiplicity and percentage of deposited dose for each secondary particle and a radial dispersion of neutrons in the material

Aplicação de painéis fotovoltaicos em residências: estudos de caso em Guaratinguetá e Sevilha (Espanha)

In this paper we discussed the possibility of installing a photovoltaic panel in a house in order to reduce electrical consumption. Brazil is a country with a huge solar resource and photovoltaic technology allows transforming solar energy into electricity, helping to decentralize energy production. To enlarge the field of view, the study compares with the equivalent in a Spanish city, discussing how the law favors the initiative of using this type of energy. It will be seen that, with the encouragement of the government, the project can be done because the installation is amortized over a reasonable period of time, about eight years in Spain and three in Brazil

Análise geoestatística da variabilidade espacial do acabamento com tingidor em painéis de madeira colada lateralmente

Classical statistical techniques which necessarily assume that all sampling units are random and independent were always used in the timber industry. Geostatistics considers that certain phenomena are characterized by spatial dependence: values of sampling units closer to each other tend to be more similar than values of sampling units farther away. This study aimed to characterize the spatial variability of the finishing (dyer) in the upper and lower surfaces of four edge glued panels by using geostatistical methods using geoR. Semivariograms were constructed for the analysis of spatial dependence. The spherical mathematical model was the best fit to the semivariograms generated, and was done the interpolation of the data (kriging) in samples where the distribution of dyer presents spatial dependence. In the bottom surfaces of two panels where the spatial dependence was detected geostatistical methods characterized a very large spatial variability due to the heterogeneous application of the finishing

Produção e caracterização físico-mecânica do compósito cimento-madeira com variação granulométrica dos resíduos lignocelulósicos

The need to reduce environmental damage and add value to waste causes more and more new alternatives appear to unite these two points. One of the main ways to achieve this in timber industries and the use of waste for making panels. This work was aimed at studying the influence of particle size and density in Eucalyptus mechanical compressive strength of cement composite wood. For this study was performed production and physico-mechanical characterization of specimens, using portland cement, water and waste eucalyptus. The methodology consists of a statistical study of the results obtained by calculating the density and axial compression tests and a subsequent comparison of these results with other studies. The results showed that there are significant differences in density and compressive strength when using different particle sizes the particles of eucalyptus. In general, the smaller the particle size, the lower the compression strength and the greater the density when the samples are produced with the same trait

Estudo da influência das resinas termofixas uréia formaldeído (UF) e melamina formaldeído (MF) nas características físicas e mecânicas de painéis MDF

Thermosetting resins are very important in the production of MDF panels. They act as an adhesive in the process of compacting and consolidating the fiberboard. Thermoset resins commonly used in this process are based resin urea formaldehyde (UF) and melamine formaldehyde (MF). The first has a higher demand due to its low cost and good performance in meeting the specifications and standards. The second has a high cost compared to MF resin, but adds greater value to the MDF panel, because it gives greater moisture resistance. The process of manufacture of MDF boards was briefly presented in this study to facilitate the understanding of the work. Samples of thermosetting resins (UF and MF) were subjected to physical-chemical seeking to relate these results to the technological performance presented by their respective samples of MDF boards. Two other samples of MDF panels were subjected to physical and mechanical tests. Results were analyzed and related to the award of their respective thermoset resin. Instruments like Dahmos Trend Manager ® and Grecon Dax 5000 and TG - DSC analysis were used in this study to assist in the analysis of the results. It was observed that the results of the analysis of thermosetting resins were within the specified. Such resins do not directly influence the technological tests provided by the MDF panels, but it has been found that the process variables such as humidity and fiber production rate interfere with the performance of the resin accelerating the reaction and therefore their influence on the physical-mechanical properties of the panels MDF. Samples of MDF panels with UF and MF met all the specifications required by the Brazilian standard with regard to the technological quality. The increased demand for UF resin market is justified by the service specifications...

Análise do desempenho físico-mecânico de painéis compensados de Pinus sp. produzidos com adesivos aquosos a base de poliacetato de vinila e de homopolímero vinílico

This study aimed to evaluate the physico-mechanical performance of three PVA adhesive formulations according to the Brazilian standards for plywood testing and to evaluate the results with those presented in the technical literature and specified in normative documents. The study presents the production process of the panels, the obtaining of samples and, finally, the implementation of physico-mechanical characterization tests based on plywood Brazilian standards. For the panels production it was used a gramature of 120 g / m² and applied a pressure of 15 bars and two temperature combinations and pressing time for each adhesive. The commercial adhesives used were PVA 1810, PVA 1060 and Vinyltec 239. The physical tests conducted were thickness swelling, density, moisture content and water absorption. The mechanical tests were static flexion, for the determination of elasticity modulus (MOE) and rupture modulus (MOR), and shear in the glue line. Among the three formulations studied none showed good performance in the presence of water. However, other trials in the adhesive showed better results and closer to the commercially equivalent used, in the case the urea-formaldehyde, was the PVA 1810, that can be applied in non-structural uses and in environments without the presence of moisture

Física de partículas no ensino médio: uma análise de materiais para apoio didático

This work consisted in analysing five materials which mean respect to subjects related to Particle Physics, aiming to explore their potentialities for the use in the High School levels, particularly by physics teachers. On this perspective, we sought to describe the contents of each material and point out their potentialities as material of didactic support. They are: 1. The purpose of Secretaria da Educação do Estado de São Paulo, presented in the Teacher's Guide of the Program São Paulo faz escola; 2. The Game Sprace Game, elaborated by the European Organization for Nuclear Research (CERN); 3. The book O discreto charme das partículas elementares, written by the professor Maria Cristina Abdalla; 4. The video O discreto charme das partículas elementares, based on the book of Professor Maria Cristina Abdalla which was produced by TV Cultura in association with the Ministério da Educação e Cultura” (MEC). The book Partículas elementares no ensino médio: uma abordagem a partir do LHC written by Wagner Franklin Balthazar and Alexandre Lopes de Oliveira, from the collection CBPF - Tópicos de Física. The work was constructed on a qualitative perspective, that is, it did not attempt to quantify the help that each material could offer to Physics teaching. One sought to describe and analyse, from different theoretical frames, their potentialities for the use in the High School level. The results indicate that all the materials analysed can contribute to the Physics teaching, and beyond, as they own format and approches distinct from the subject, they can be used as a whole or in parts, together or separately, depending on the objectives to be reached and on the profile of the target public

Produção de partículas secundárias em reações de “spallation” induzidas por prótons

Cosmic radiation has been identi ed as one of the main hazard to crew, aircraft and sensitive equipments involved in long-term missions and even high-altitude commercial ights. Generally, shields are used in spatial units to avoid excessive exposure, by holding the incident radiation. Unfortunatelly, shielding in space is problematic, especially when high-energy cosmic particles are considered, due to the production of large number of secondary particles, mainly neutrons, protons and alpha particles, caused by spallation reactions and quasi-elastic processes of the corpuscular radiation with the shield. Good parameters for checking the secondary particle production at target material are diferential cross section and energy deposited in the shield. Addition experiments, some computer codes based on Monte Carlo method show themselves a suitable tool to calculate shield parameters, due to have evaluated nuclear data libraries implemented on the algorithm. In view of this, the aim of this work is determining the parameters evaluated in shielding materials, by using MCNPX code, who shows good agreement with experimental data from literature. Among the materials, Aluminium had lower emission and production of secondary particles

Estudo teórico da contribuição a dose de partículas secundárias geradas por prótons de energias entre 100-200 MeV num phantom de osso compacto

The contribution of the total dose due to deposition of secondary energy particles caused by nuclear inelastic processes (n, 2H, 3H, 3He and  ) in proton therapy is an opened problem and in discussion. In the calculations of plans implemented for routine treatment, the paid dose is calculated whereas that the proton loses energy by ionization and or coulomb excitement. The contribution of inelastic processes associated with nuclear reactions is not considered, mainly due to the difficulty of processing targets consisting of various materials. In this sense, there are only estimates for pure materials or simple composition (water, for example).This work presents the results of simulations by the Monte Carlo method employing the code MCNPX v2.50 (Monte Carlo N-Particle eXtended) of the contribution to the total dose of secondary particles. The study was implemented in a cylindrical phantom composed by compact bone, for monochromatic beams of protons between 100 and 200 MeV with pencil beam form