Development and validation of a new and rapid HPLC for determination of lyophilized teicoplanin

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Development and validation of a dissolution test for diltiazem hydrochloride in immediate release capsules

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Development on polymeric precursor routes to produce superconducting nanoparticles

The well-known polymeric precursor route is a simple and low-cost sol-gel method based on the preparation of an aqueous precursor solution of metals followed by the addition of a water-soluble polymer. This method consists of a polyesterification process between a metal chelate complex by using a hydroxycarboxylic acid and a polyhydroxy alcohol. In this work, citric acid (CA), tartaric acid (TA) and ethylenediaminetetraacetic acid (EDTA) are used as the hydroxycarboxylic acid and ethylene glycol (EG) is used as the polyhydroxy alcohol. The effects of the precursor pH solution, time and temperature of polymerization step as well as the combination of different chelating agents in order to obtain nanoscopic YBa2Cu3Oy samples were traced. (c) 2007 Elsevier B.V. All rights reserved.

Alternative parameters for the continuation power flow method

The conventional Newton's method has been considered inadequate to obtain the maximum loading point (MLP) of power systems. It is due to the Jacobian matrix singularity at this point. However, the MLP can be efficiently computed through parameterization techniques of continuation methods. This paper presents and tests new parameterization schemes, namely the total power losses (real and reactive), the power at the slack bus (real or reactive), the reactive power at generation buses, the reactive power at shunts (capacitor or reactor), the transmission lines power losses (real and reactive), and transmission lines power (real and reactive). Besides their clear physical meaning, which makes easier the development and application of continuation methods for power systems analysis, the main advantage of some of the proposed parameters is that its not necessary to change the parameter in the vicinity of the MLP. Studies on the new parameterization schemes performed on the IEEE 118 buses system show that the ill-conditioning problems at and near the MLP are eliminated. So, the characteristics of the conventional Newton's method are not only preserved but also improved. (C) 2003 Elsevier B.V. B.V. All rights reserved.

Validation of an HPLC Method for quantitative Determination of Benzocaine in PHBV-Microparticles and PLA-Nanoparticles

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Development of phantom for radiographic image optimization of standard patient in the lateral view of chest and skull examination

We present the construction of a homogeneous phantom to be used in simulating the scattering and absorption of X-rays by a standard patient chest and skull when irradiated laterally. This phantom consisted of Incite and aluminium plates with their thickness determined by a tomographic exploratory method applied to the anthropomorphic phantom. Using this phantom, an optimized radiographic technique was established for chest and skull of standard sized patient in lateral view. Images generated with this optimized technique demonstrated improved image quality and reduced radiation doses. (c) 2006 Elsevier Ltd. All rights reserved.

A rapid, environmentally friendly, and reliable method for pesticide analysis in high-fat samples

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Common factors method to predict the carcass composition tissue in kid goats

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Development and application of methods for determination of residual monomer in dental acrylic resins using high performance liquid chromatography

Two high-performance liquid chromatographic methods for determination of residual monomer in dental acrylic resins are described. Monomers were detected by their UV absorbance at 230 nm, on a Nucleosil((R)) C-18 (5 mu m particle size, 100 angstrom pore size, 15 x 0.46 cm i.d.) column. The separation was performed using acetonitrile-water (55:45 v/v) containing 0.01% triethylamine (TEA) for methyl methacrylate and butyl methacrylate, and acetonitrile-water (60:40 v/v) containing 0.01% TEA for isobutyl methacrylate and 1,6-hexanediol dimethacrylate as mobile phases, at a flow rate of 0.8 mL/min. Good linear relationships were obtained in the concentration range 5.0-80.0 mu g/mL for methyl methacrylate, 10.0-160.0 mu g/mL for butyl methacrylate, 50.0-500.0 mu g/mL for isobutyl methacrylate and 2.5-180.0 mu g/mL for 1,6-hexanediol dimethacrylate. Adequate assay for intra- and inter-day precision and accuracy was observed during the validation process. An extraction procedure to remove residual monomer from the acrylic resins was also established. Residual monomer was obtained from broken specimens of acrylic disks using methanol as extraction solvent for 2 h in an ice-bath. The developed methods and the extraction procedure were applied to dental acrylic resins, tested with or without post-polymerization treatments, and proved to be accurate and precise for the determination of residual monomer content of the materials evaluated. Copyright (c) 2005 John Wiley & Sons, Ltd.

The kinetic mechanism of human uridine phosphorylase 1: Towards the development of enzyme inhibitors for cancer chemotherapy

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Novel production method of porous surface Ti samples for biomedical application

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Validated HPLC method for the standardization of Phyllanthus niruri (herb and commercial extracts) using corilagin as a phytochemical marker

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Validated high-performance liquid chromatographic method for the standardisation of Ptychopetalum olacoides Benth., Olacaceae, commercial extracts

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Development of a bioassay to quantify the ricin toxin content of castor bean (Ricinus communis L.) seeds

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

On the development of the brown spider Loxosceles gaucho Gertsch (Araneae, Sicariidae): the nympho-imaginal period

Observations of the developmental biology of Loxosceles gaucho Gertsch, 1967, the brown spider of southeastern Brazil are scarce. The present study reports the method of individualized rearing of 18 populations of L. gaucho, kept in laboratory under varied diet conditions, and characterizes their nympho-imaginal period as well as factors related to their reproduction. Females built the first egg sac about 20 days after copulation and nymphs hatched 40 days after the laying date. Average offspring was 61.3 spiderlings and females usually built three to four successive egg sacs in a period of five to seven months. First nymphs initiated their predatory activity between the 5th and 8th days after hatching and the majority reached adulthood within six moults (range of five to eight) in approximately 15 to 17 months (male) and 15.5 to 18 months (female). The average sex ratio equaled 1.0:1.7 (male:female). The wide individual variability of this species intermoult intervals is herewith expressed by the intermoult rate, which was fairly uniform for both intra and interpopulations and gives a relevant aspect for a general idea of the life cycles of spiders.