Low-level laser therapy in pediatric bell's palsy: Case report in a three-year-old child

Objectives: The objective of this study was to apply low-level laser therapy (LLLT) to accelerate the recovery process of a child patient with Bell's palsy (BP). Design: This was a prospective study. Subject: The subject was a three-year-old boy with a sudden onset of facial asymmetry due to an unknown cause. Materials and methods: The low-level laser source used was a gallium aluminum arsenide semiconductor diode laser device (660 nm and 780 nm). No steroids or other medications were given to the child. The laser beam with a 0.04-cm2 spot area, and an aperture with approximately 1-mm diameter, was applied in a continuous emission mode in direct contact with the facial area. The duration of a laser session was between 15 and 30 minutes, depending on the chosen points and the area being treated. Light was applied 10 seconds per point on a maximum number of 80 points, when the entire affected (right) side of the face was irradiated, based on the small laser beam spot size. According to the acupuncture literature, this treatment could also be carried out using 10-20 Chinese acupuncture points, located unilaterally on the face. In this case study, more points were used because the entire affected side of the face (a large area) was irradiated instead of using acupuncture points. Outcome measures: The House-Brackmann grading system was used to monitor the evolution of facial nerve motor function. Photographs were taken after every session, always using the same camera and the same magnitude. The three-year-old boy recovered completely from BP after 11 sessions of LLLT. There were 4 sessions a week for the first 2 weeks, and the total treatment time was 3 weeks. Results: The result of this study was the improvement of facial movement and facial symmetry, with complete reestablishment to normality. Conclusions: LLLT may be an alternative to speed up facial normality in pediatric BP. © Copyright 2013, Mary Ann Liebert, Inc. 2013.

Influência do sistema de cimentação adesiva e da fonte de luz fotoativadora na resistência à extrusão de pinos de fibra de vidro

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Efeito do ultra-som de baixa potência na reparação óssea em ratos sob ausência de carga: análise densitométrica e biomecânica

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Efeito do fresamento com alta velocidade de corte na integridade superficial de aços ferríticos com grãos ultrafinos

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Portaferramentas para torneamento com refrigeração interna baseada na mudança de fase do fluido

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Resistência de união de cimentos resinosos, ao cisalhamento, variando o substrato e o material restaurador

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Proposta de uma metodologia para obtenção de um gerador síncrono com rotor de ímãs permanentes inclinados axialmente para microcentrais elétrica a partir de motor de indução

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Hot turning of a difficult-to-machine steel (sae xev-f) aided by infrared radiation

A possible way for increasing the cutting tool life can be achieved by heating the workpiece in order to diminish the shear stress of material and thus decrease the machining forces. In this study, quartz electrical resistances were set around the workpiece for heating it during the turning. In the tests, heat-resistant austenitic alloy steel was used, hardenable by precipitation, mainly used in combustion engine exhaustion valves, among other special applications for industry. The results showed that in the hot machining the cutting tool life can be increased by 340% for the highest cutting speed tested and had a reduction of 205% on workpiece surface roughness, accompanied by a force decrease in relation to conventional turning. In addition, the chips formed in hot turning exhibited a stronger tendency to continuous chip formation indicating less energy spent in material removal process. Microhardness tests performed in the workpieces subsurface layers at 5 m depth revealed slightly higher values in the hot machining than in conventional, showing a tendency toward the formation of compressive residual stress into plastically deformed layer. The hot turning also showed better performance than machining using cutting fluid. Since it is possible to avoid the use of cutting fluid, this machining method can be considered better for the environment and for the human health.

Usinabilidade e integridade superficial de implantes dentários

Pós-graduação em Engenharia Mecânica - FEIS

Influência da geometria oclusal e material restaurador na carga para fratura e distribuição de tensões em coroas totais

Pós-graduação em Odontologia Restauradora - ICT

New LLLT protocol to speed up the bone healing process-histometric and immunohistochemical analysis in rat calvarial bone defect

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Efeito das diferentes direções de aplicação de jato de fluido de corte no torneamento de um aço de difícil usinagem

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Efeito na adesão de pinos de fibra de vidro na dentina radicular após irrigação com diferentes formulações de ácido peracético e cimentação com RelyX U200

Pós-graduação em Odontologia - FOAR