A SIMPLE METHOD FOR DETERMINING LOCATION OF FORAGING ANT NESTS USING LEAF-CUTTING ANTS AS A MODEL

In many situations, it is difficult to evaluate the location of nests of ants, especially in tropical systems, or to determine which trail system corresponds with which nest, as in the case of high-density populations of leaf-cutting ants, Atta spp. Fragments of colored drinking straws coated with an attractant, generally vegetable oil and/or a starchy carbohydrate, are carried by ants and following removal of the attractant are deposited in middens, allowing determination of the origin of foraging workers.

Evaluation of cutting patterns produced in primary teeth by an air-abrasion system

Objective: the aim of this in vitro study was to assess the effect of tip diameter, nozzle distance, and application time of an air-abrasion system for cavity preparation on the enamel of primary teeth. Method and materials: Forty exfoliated primary teeth were air abraded with a microabrasion machine used with a handpiece with an 80-degree-angle nozzle, 50-mum abrasive particle size, and 80-psi air pressure. The effects of 0.38- or 0.48-mm inner tip diameter, 2- or 5-mm distance from tip to tooth surface, and 15 or 30 seconds of application time on cutting efficiency were evaluated. Cutting width and depth were analyzed and measured from scanning electron micrographs. Results: Statistical analysis revealed that the width of the cuts was significantly greater when the tip distance was increased. Significantly deeper cavities were produced by a tip with a 0.48-mm inner diameter. The application time did not influence the cuts. Conclusion: the cutting patterns found in this study suggest that precise removal of enamel in primary teeth is best accomplished when a tip with a 0.38-mm inner diameter is used at a 2-mm distance.

The application of preprocessing and cutting plane techniques for a class of production planning problems

This paper investigates properties of integer programming models for a class of production planning problems. The models are developed within a decision support system to advise a sales team of the products on which to focus their efforts in gaining new orders in the short term. The products generally require processing on several manufacturing cells and involve precedence relationships. The cells are already (partially) committed with products for stock and to satisfy existing orders and therefore only the residual capacities of each cell in each time period of the planning horizon are considered. The determination of production recommendations to the sales team that make use of residual capacities is a nontrivial optimization problem. Solving such models is computationally demanding and techniques for speeding up solution times are highly desirable. An integer programming model is developed and various preprocessing techniques are investigated and evaluated. In addition, a number of cutting plane approaches have been applied. The performance of these approaches which are both general and application specific is examined.

Winged leaf-cutting ants on nuptial flights used as transport by Attacobius spiders for dispersal

1. Sexuals of a leaf-cutting ant, Atta bisphaerica Forel, left their nest for nuptial flights in October to December.2. When leaving a nest, 53 of the 479 winged sexuals (or alates) observed (11.1%) carried up to three inquiline spiders of Attacobius luederwaldti.3. Spiders exclusively selected winged sexuals, not workers, and preferred females, indicating their expectation of the stronger flight ability of females. Neither these sexuals nor workers that appeared out of the nest on flight days attempted to remove or attack spiders on the body of alates.4. New qucens landing from their nuptial flight did not carry spiders, indicating that the spiders had left the ants in the sky to be dispersed by wind.5. No spiders were found in more than 100 incipient nests, which were estimated to be 2-3 months old. This suggests that the spiders jumped off the alate during mid-flight and dispersed on the wind to inhabit larger nests.

Effect of handpiece tip design on the cutting efficiency of an air abrasion system

Purpose : the aim of this study was to evaluate the effect of nozzle angle and tip diameter on the cutting efficiency of an air abrasion system. Materials and Methods: Thirty-six extracted human third molars were air-abraded with the PrepStar microabrasion machine using a handpiece with either 80degrees or 45degrees nozzle angles with 0.38 or 0.48 nun tip orifice diameters. The following parameters were held constant: abrasive particle size (27 mum), air pressure (80 psi), distance (2 mm.) and duration (15 seconds). The cutting efficiency was compared using enamel, dentin and cementum substrates. Width and depth of the cutting patterns were analyzed and measured using scanning electron micrographs. Results: Statistical analysis using three-way ANOVA and Duncan's Multiple Range test revealed that the width of the cuts was significantly greater when the cavities were prepared using the 45degrees nozzle angle. Significantly deeper cavities were produced with the 80degrees nozzle angle. The tip orifice of the nozzle influenced the cutting efficiency in softer substrates, dentin and cementum. Precise removal of hard tissue is best accomplished using the 80degrees angle nozzle tips for all types of tooth surfaces, enamel, dentin and cementum.

DECOMPOSITION RATES OF SPENT FUNGAL REFUSE OF ATTA-SEXDENS (HYMENOPTERA, FORMICIDAE) AND IMPLICATIONS FOR ESTIMATING FORAGE INTAKE BY LEAF-CUTTING ANTS

Using simulated ceramic refuse chambers, field decomposition studies were performed on the spent fungal refuse of the lead-cutting ant Atta sexdens rubropilosa. Refuse half life was estimated at 40 days, with complete decomposition at 100 days. These results suggest that the conversion-factor method used to estimate forage input into leaf-cutting ant colonies must be corrected for decomposition, or serious estimation errors will occur.

An evolutionary algorithm for the one-dimensional cutting stock problem

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Ventilation of the giant nests of Atta leaf-cutting ants: does underground circulating air enter the fungus chambers?

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

A Lagrangian relaxation approach to a coupled lot-sizing and cutting stock problem

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)