Morphology of the vas deferens in an ethanol-drinking strain of rats (UChA and UChB)

Chronic alcoholism alters reproduction and therefore may be responsible for alterations of vas deferens, which are the subject of this analysis in UCh ethanol-drinking rats. The proximal and distal segments of the vas deferens of 20 animals were submitted to macroscopic, light microscopy, electron microscopy and morphometric analysis. The UCh rats showed atrophy of the epithelium of the vas deferens and alterations of the hypothalamus-pituitary axis. Ethanol induces changes in the epithelium of the vas deferens and hypothalamus-pituitary axis of UCh rats.

High sensitivity low cost capacitive strain gage

This paper describes a high senstivity low cost capacitive strain gage sensor. The theory, design, and sensor construction details are presented. It consists of eight capacitive sensors connected in two full bridges. The capacitive strain gage sensor structure was designed in order to produce high sensitivity and low dependence with temperature. By using a simple signal conditioning circuit constituted by a differential amplifier, a band-pass filter, and a precision rectifier the device can measure forces with resolution of 0.009 N and precision of 98.7%. It is rugged, presents linear response, and good repeatability. It presents sensitivity of 8.7 V/N and fall time of 12 ms.

Production of CGTase by a bacillus Alkalophilic CGII strain isolated from wastewater of a manioc flour industry

GCTase production by a new strain of Bacillus alkalophillc CGII isolated from Brazilian wastewater of manioc flour industry was examined. The growth medium used was composed by 1.5% starch, 1.5% nitrogen and 1% Na 2CO3. Higher activity was obtained with starch, maltodextrin and galactose. When glucose was added to the medium, no enzyme production was observed. High enzyme activity and growth were reached when aeration was increased (88.6 U/mL). The enzyme characterization showed an optimum pH and temperature 8.0 and 55°C for starch hydrolyses, respectively. Mg+ and Ca++ showed small activation; however, Hg + and Cu+ showed a strong enzyme inhibition.

Influence of activation modes on diametral tensile strength of dual-curing resin cements.

In metallic restorations, the polymerization of dual-curing resin cements depends exclusively on chemical activation. The effect of the lack of photoactivation on the strength of these cements has been rarely studied. This study evaluated the influence of activation modes on the diametral tensile strength (DTS) of dual-curing resin cements. Base and catalyst pastes of Panavia F, Variolink II, Scotchbond Resin Cement, Rely X and Enforce were mixed and inserted into cylindrical metal moulds (4 x 2 mm). Cements were either: 1) not exposed to light (chemical activation = self-cured groups) or 2) photoactivated through mylar strips (chemical and photo-activation = dual-cured groups) (n = 10). After a 24 h storage in 37 masculineC distilled water, specimens were subjected to compressive load in a testing machine. A self-curing resin cement (Cement-It) and a zinc phosphate cement served as controls. Comparative analyses were performed: 1) between the activation modes for each dual-curing resin cement, using Students t test; 2) among the self-cured groups of the dual-curing resin cements and the control groups, using one-way ANOVA and Tukeys test (alpha = 0.05). The dual-cured groups of Scotchbond Resin Cement (53.3 MPa), Variolink II (48.4 MPa) and Rely X (51.6 MPa) showed higher DTS than that of self-cured groups (44.6, 40.4 and 44.5 MPa respectively) (p < 0.05). For Enforce (48.5 and 47.8 MPa) and Panavia F (44.0 and 43.3 MPa), no significant difference was found between the activation modes (p > 0.05). The self-cured groups of all the dual-curing resin cements presented statistically the same DTS as that of Cement-It (44.1 MPa) (p > 0.05), and higher DTS than that of zinc phosphate (4.2 MPa). Scotchbond Resin Cement, Variolink II and Rely X depended on photoactivation to achieve maximum DTS. In the absence of light, all the dual-curing resin cements presented higher DTS than that of zinc phosphate and statistically the same as that of Cement-It (p > 0.05).

Evaluation of serum- and animal protein-free media for the production of infectious bronchitis virus (M41) strain in a continuous cell line

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Influência da posição diametral das tábuas e da vaporização nos defeitos de secagem de Eucalyptus grandis

This study evaluated the Eucalyptus grandis drying defects acting on boards diametrical position and on log steaming. Half of the logs, with diameter from 20 to <25, 25 to <30 and 30 to <35cm, were steamed during 20 hours at 90°C of temperature. Subsequently, the logs (control and steamed) were sawn. The boards were dried in the dry-kiln pilot and the resulting defects from the drying process were measured. The results indicate that: (1) the boards coming from control logs presented different magnitude defects in function of the diametrical position. The split and spring to increase in direction to pith, the bow to increase in direction to bark and cupping were bigger in intermediary boards; (2) the boards coming from steamed logs presented a reduction from drying defects in function of logs diameter and its more homogeneous index in the pith-bark direction.

Strain relaxation and stress-driven interdiffusion in InAsInGaAsInP nanowires

The authors have investigated strain relaxation in InAsInGaAsInP nanowires (NW's). Transmission electron microscopy images show an additional stress field attributed to compositional modulation in the ternary layer, which disrupts NW formation and drives Ga interdiffusion into InAs, according to grazing incidence x-Ray diffraction under anomalous scattering conditions. The strain profile along the NW, however, is not significantly affected when interdiffusion is considered. Results show that the InAs NW energetic stability is preserved with the introduction of ternary buffer layer in the structure. © 2007 American Institute of Physics.

Diametral tensile strength of dual-curing resin cements submitted exclusively to autopolymerization.

OBJECTIVES: To evaluate, at different times, the diametral tensile strength (DTS) of dual-curing resin cements that were not photopolymerized. METHOD AND MATERIALS: Equal amounts of base and catalyst pastes of Panavia F (Kuraray), Variolink II (Vivadent), Rely X (3M ESPE), and Enforce (Dentsply) were mixed and inserted into cylindrical molds (4 x 2 mm) (n = 10). Cements were not photopolymerized. DTS test was performed in a testing machine at 30 minutes, 1 hour, 24 hours, and 7 days. The specimens were stored in light-proof containers with distilled water at 37 degrees C until the time of assay. An autopolymerizing resin cement (Cement-It, Jeneric Pentron) and a zinc phosphate cement served as controls. One-way analysis of variance (ANOVA) and Tukey test were performed separately for each cement and for each time (P <.05). RESULTS: All cements showed an increase in DTS when tested at 1 and 24 hours. Tests at 24 hours and 7 days revealed no statistically significant differences. In all groups, the zinc phosphate cement had the lowest DTS mean values (2.1 MPa, 3.6 MPa, 6.5 MPa, and 6.9 MPa), while Cement-It (35.1 MPa, 33.6 MPa, 46.9 MPa, and 46.3 MPa) and Enforce (31.9 MPa, 31.7 MPa, 43.4 MPa, and 47.6 MPa) presented the highest DTS mean values. CONCLUSION: All cements presented maximal strength at 24 hours. The dual-curing resin cements, even when nonphotopolymerized, demonstrated higher DTS than the zinc phosphate cement and similar or lower values than the autopolymerizing resin cement.

Application of a serum/protein-free medium for the growth of mammalian cell lines and high level production of classical, variant and very virulent strain of infectious bursal disease virus (IBDV)

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Experimental infection of commercial layers using a Salmonella enterica serovar Gallinarum strain: Leukogram and serum acute-phase protein concentrations

The aim of the present study was to evaluate white blood cell counts and serum protein profiles of commercial layers experimentally infected with Salmonella Gallinarum (SG) in order to better understand the pathophysiology of the disease caused by this bacterium. 180 five-day-old commercial layers were divided into 3 groups (G); G1 and G2 received 0.2 mL of inoculate containing 3.3x10 8 CFU or 3.3×10 5 CFU SG resistant to nalidix acid (Nal r)/mL, respectively, directly into their crops. G3 group did not receive the inoculum. Birds were sacrificed 24 hours before (T1) and 24 hours after the infection (T2), and three (T3), five (T4), seven (T5), and ten (T6) days after the administration of the inoculum. White blood cell counts were carried out in a Neubauer hemocytometer and in blood smears. Serum protein concentrations, including acute-phase proteins, were determined using sodium dodecyl sulphate-polyacrylamide gel electrophoresis (SDS-PAGE). Data were submitted to analysis of variance, and means were compared by Tukey's test (P <0.05). G1 and G2 groups presented higher leukocyte counts on T4 and T5, respectively, due to the increase of circulating lymphocytes and heterophils, with a significant difference relative to G3. In electrophoresis, an increase in the serum levels of ceruloplasmin, haptoglobin, and hemopexin and a decrease in transferrin, which are acute-phase proteins, was verified. IgA serum levels did not change; however, IgG concentration increased during the infection. In conclusion, the results provide information for the better understanding of the pathophysiology of fowl typhoid.

Experimental infection of commercial layers using a Salmonella enterica sorovar Gallinarum strain: Blood serum components and histopathological changes

The purpose of the study was to evaluate the blood serum components and histopathological findings of commercial layers experimentally infected with Salmonella Gallinarum (SG), the microorganism responsible for the fowl typhoid. 180 commercial layers were distributed into three groups (G): G1 and G2 received 0.2mL of inoculum containing 3.3x10 8 and 3.3x10 5 CFU of resistant SG to the nalidix acid (Nal r)/mL, respectively, directly into their crops; G3 did not receive the inoculum (control group). The birds were inoculated when they were 5 days old and the euthanasia was performed 24 hours before and after infection and 3, 5, 7 and 10 days after the administration of the inoculum. In each day of collection, blood samples were obtained for biochemical tests of the blood serum besides macroscopic and histopathological examination of the birds. Data were submitted to analysis of variance by the SAS statistical program and the means were compared by Tukeýs test (P<0,05). In the serum biochemical profile it was observed that the infection interfered in the values of total protein, albumin, calcium, phosphorus, cholesterol, triglycerides, GGT and ALT in the infected groups. The macroscopic examination showed hepatomegaly, alteration of the hepatic color and hemorrhagic spots in the kidneys of animals from G1. The histopathology showed degeneration of hepatocytes in G1 and G2 although other lesions like multifocal hepatic necrosis and inflammatory infiltrate on the liver and kidneys were restricted to G1. The alterations were more evident on G1 which received a higher concentration of bacteria/mL when compared to G2. The results showed that the correlation between biochemical alterations and macroscopic and histopathological lesions can assist the comprehension of the pathophysiology of fowl typhoid, supplying important information for the diagnosis and prognosis of this disease.

Theoretical approach including friction for determining strain limits in punch stretching of anisotropic sheet metals

A new analytical theory including friction was developed to assess strain limits in punch stretching of anisotropic sheet metals. This new approach takes into consideration the anisotropic behaviour of sheet materials and could explain the mechanical behaviour of a variety of anisotropic sheet materials. The theory explains the sheet metal failure so for the drawing as the stretching region of the forming limit curve, particularly for materials that present the strain-ratio dependence of limit strain ε 1, where dε 1/dρ is not always greater than zero. dε 1/ dρ or dε 1/dε 2 could be equal to or smaller than zero for a range of materials. Therefore, this new theory can explains such experimental observations, besides to assuming that membrane element relations near the pole, for the case of punch stretching are dependent of sheet metal properties as the process history and also suggests that the onset of local necking is controlled by shear. Thus, theoretical results obtained through this new approach are compared with experimental results available in the literature. It is demonstrated the effect of friction on a FLC curve for both regions, drawing and stretching. © 2010 American Institute of Physics.

Effect of axial loads on implant-supported partial fixed prostheses by strain gauge analysis

Objectives: The present study used strain gauge analysis to perform an in vitro evaluation of the effect of axial loading on 3 elements of implant-supported partial fixed prostheses, varying the type of prosthetic cylinder and the loading points. Material and methods: Three internal hexagon implants were linearly embedded in a polyurethane block. Microunit abutments were connected to the implants applying a torque of 20 Ncm, and prefabricated Co-Cr cylinders and plastic prosthetic cylinders were screwed onto the abutments, which received standard patterns cast in Co-Cr alloy (n = 5). Four strain gauges (SG) were bonded onto the surface of the block tangentially to the implants, SG 01 mesially to implant 1, SG 02 and SG 03 mesially and distally to implant 2, respectively, and SG 04 distally to implant 3. Each metallic structure was screwed onto the abutments with a 10 Ncm torque and an axial load of 30 kg was applied at five predetermined points (A, B, C, D, E). The data obtained from the strain gauge analyses were analyzed statistically by RM ANOVA and Tukey's test, with a level of significance of p<0.05. Results: There was a significant difference for the loading point (p=0.0001), with point B generating the smallest microdeformation (239.49 με) and point D the highest (442.77 με). No significant difference was found for the cylinder type (p=0.748). Conclusions: It was concluded that the type of cylinder did not affect in the magnitude of microdeformation, but the axial loading location influenced this magnitude.

Safety and efficacy of a Salmonella Gallinarum ΔcobSΔcbiA strain with potential to prevent chicken infections by Salmonella Gallinarum and Salmonella Enteritidis

New vaccine design techniques have allowed the development of effective vaccine strains against Salmonella infections in which the risks of reversion to the wild type and virulence is null. The mutant strain Salmonella Gallinarum ΔcobSΔcbiA was previously shown to be avirulent in chickens. In this study, this strain was tested as a vaccine against Salmonella Gallinarum (SG) and S. Enteritidis (SE) infections, and its protection levels, safety and possible risks of reversion to virulence after vaccination of layers were evaluated. Birds were vaccinated at five days of age or at five and 25 days of age. At 45 days of age, brown and white layers were challenged with SG and SE wild strains, respectively. Two assays to test the possibility of reversion to virulence were performed. Five successive bacterial passages in brown layers were carried out in the first assay. In the second assay, brown layers received a ten-fold concentrated inoculum of the SGΔcobSΔcbiA strain and were evaluated for clinical signs and mortality. In both experiments, no birds that received the inoculation of the attenuated strain died. Additionally, the use of the mutant strain as a vaccine provided good protection levels against both challenge strains.

Keratinase production by new strain of Bacillus Amyloliquefaciens: Application of statistical experimental design for optimization of keratinase production

Feathers are rich in amino acids and can be employed as a dietary protein supplement for animal feed. Microbial degradation is an alternative technology for improving the nutritional value of feathers. Other potential applications of keratinase include use in the leather industry, detergents and medicine as well as the pharmaceutical for the treatment of acne, psoriasis and calluses. A new keratinolytic enzyme production bacterium was isolated from a poultry processing plant. To improve keratinase yield, statistically based experimental designs were applied to optimize three significant variables: temperature, substrate concentration (feathers) and agitation speed. Response surface methodology demonstrated an increase in keratinolytic activity at temperature, agitation speed and substrate concentration of 26.6°C, 150 rpm and 2%, respectively. Liquid chromatography revealed the release of amino acids in the Bacillus amyloliquefaciens culture broth, thereby demonstrating the potential of feather meal in the animal feed industry. © Global Science Publications.