Recovery of degraded areas using topsoil in the Amazon rainforest

This study is aimed at evaluating the effect of placing the top soil cover areas, such as tailings degraded by tin mining, in the Amazon rainforest in Brazil. The evaluations of the planting sites occurred in areas where tin mining was carried out, basically planting native trees over a period of seven years. This work did not come from a pre-decreed methodology of experimental design, and data was collected only seven years after planting. Thus, it was not possible to identify all variables that contributed to a better recovery of the areas. Sampling was done about seven years after placing the top soil and is determined: pH, organic matter content, P, K, Ca, Mg, Al, cation exchange capacity (T), base saturation (V%), B, Fe, Zn, Cu and Mn. The native forest species existing at the site were evaluated in relation to height (in meters) and diameter of the base. For all sites where the surface layer of soil was applied, there were significant differences in the growth of native species. A fundamental aspect in the rehabilitation of areas degraded by mining, in general, is the knowledge about the soil where that recovery must be conducted. The specific procedures in the rehabilitation of those areas depend essentially on the physical, chemical, biological and mineralogical properties of the soil, which must present conditions for the adequate development of the plants. The initial idea of implanting a project of recovery of soils degraded by mining in the Amazon Forest emerged from a first visit to the field, carried out in 1998. The conditions of the already mined areas, in comparison to the exuberant forest of the surroundings caught our attention. The mining company that acts in the area had already been trying for some time to implant a plan of recovery of these mining areas, however without reaching any significant positive results. The loss of organic matter is one of the main problems of degraded areas in Brazil. The storage and reuse of a blanket of soil (topsoil) produce excellent results, but most of the miners consider this technique expensive and difficult because of operational costs and the sharp topographical condition of the mine site. Therefore, a research project was elaborated prioritizing the recovery of the soil degraded by the tin mining as a prior step to the recovery activities with native forest species. The formation of a superficial pseudo-horizon that supported the vegetation and the time that it would take for its establishment became the main objective of this research. The objective of this work is to verify the levels of elements and their traces in areas where top soils were applied for the remediation of degraded areas with local re-vegetation. © 2011 WIT Press.

Signal classification of submerged aquatic vegetation based on the hemispherical-conical reflectance factor spectrum shape in the yellow and red regions

The water column overlying the submerged aquatic vegetation (SAV) canopy presents difficulties when using remote sensing images for mapping such vegetation. Inherent and apparent water optical properties and its optically active components, which are commonly present in natural waters, in addition to the water column height over the canopy, and plant characteristics are some of the factors that affect the signal from SAV mainly due to its strong energy absorption in the near-infrared. By considering these interferences, a hypothesis was developed that the vegetation signal is better conserved and less absorbed by the water column in certain intervals of the visible region of the spectrum; as a consequence, it is possible to distinguish the SAV signal. To distinguish the signal from SAV, two types of classification approaches were selected. Both of these methods consider the hemispherical-conical reflectance factor (HCRF) spectrum shape, although one type was supervised and the other one was not. The first method adopts cluster analysis and uses the parameters of the band (absorption, asymmetry, height and width) obtained by continuum removal as the input of the classification. The spectral angle mapper (SAM) was adopted as the supervised classification approach. Both approaches tested different wavelength intervals in the visible and near-infrared spectra. It was demonstrated that the 585 to 685-nm interval, corresponding to the green, yellow and red wavelength bands, offered the best results in both classification approaches. However, SAM classification showed better results relative to cluster analysis and correctly separated all spectral curves with or without SAV. Based on this research, it can be concluded that it is possible to discriminate areas with and without SAV using remote sensing. © 2013 by the authors; licensee MDPI, Basel, Switzerland.

Maxillary Rehabilitation Using Fixed and Removable Partial Dentures with Attachments: A Clinical Report

Despite requiring dental crown preparation and possible root canal treatment, besides the difficulty of clinical and laboratory repairs, and financial burden, the association between fixed (FPD) and removable partial dentures (RPD) by means of attachments is an important alternative for oral rehabilitation, particularly when the use of dental implants and FPDs is limited or not indicated. Among the advantages of attachment-retained RPDs are the improvements in esthetics and biomechanics, as well as correction of the buccal arrangement of anterior teeth in Kennedy Class III partially edentulous arches. This article describes the treatment sequence and technique for the use of attachments in therapy combining FPD/RPD. © 2013 by the American College of Prosthodontists.

Association between physical activity and cardiovascular risk factors in individuals undergoing cardiac rehabilitation program

Introduction: Physical activity (PA) practice presents an inverse relation with risk factors (RF) of cardiovascular disease, with positive effects in quality of life and other physical and psychological variables. However, the benefits of daily activities have not been established. Objective: To investigate the prevalence and association of cardiovascular risk factors and physical activity in different categories of patients under a cardiac rehabilitation program. Methods: 69 participants of a cardiac rehabilitation program were evaluated and weight, height and blood pressure were checked. Afterwards, the patients answered questionnaires to assess self-reported physical activity level, stress level and verify the presence of RF. Logistic regression was used to estimate odds ratio. Results: High prevalence of RF was found in the subjects, age and hypertension were more prevalent while smoking and stress had lower prevalence. Most individuals were classified as sedentary, except for locomotion PA (LPA). Conclusion: That there is high prevalence of RF in patients attending cardiac rehabilitation programs, while sedentary ones are more likely to have the RF hypertension, obesity, smoking, alcohol and stress than the active ones, depending on the PA category.

Rehabilitation of maxillary cleft with hybrid obturator prosthesis

The hybrid obturator prosthesis aims to provide a sense of well-being to the patient, offering improvements in speech, chewing, and swallowing. Thus, the retention and stabilization of the prosthesis become decisive factors for the success of the rehabilitation treatment. The objective of this study was to describe the treatment of a 70-year-old man with a congenital maxillary cleft performed through aesthetic and functional prosthetic rehabilitation with hybrid obturator prosthesis. In this study, the fabricated prosthesis achieved its purpose by providing adequate functional and aesthetic conditions to the patient, promoting the reduction of airspace through the sealing of the oronasal communication, with consequent improvement in the quality of life. Copyright © 2013 by Mutaz B. Habal, MD.

Disturbances, elevation, topography and spatial proximity drive vegetation patterns along an altitudinal gradient of a top biodiversity hotspot

The correlation between vegetation patterns (species distribution and richness) and altitudinal variation has been widely reported for tropical forests, thereby providing theoretical basis for biodiversity conservation. However, this relationship may have been oversimplified, as many other factors may influence vegetation patterns, such as disturbances, topography and geographic distance. Considering these other factors, our primary question was: is there a vegetation pattern associated with substantial altitudinal variation (10-1,093 m a.s.l.) in the Atlantic Rainforest-a top hotspot for biodiversity conservation-and, if so, what are the main factors driving this pattern? We addressed this question by sampling 11 1-ha plots, applying multivariate methods, correlations and variance partitioning. The Restinga (forest on sandbanks along the coastal plains of Brazil) and a lowland area that was selectively logged 40 years ago were floristically isolated from the other plots. The maximum species richness (>200 spp. per hectare) occurred at approximately 350 m a.s.l. (submontane forest). Gaps, multiple stemmed trees, average elevation and the standard deviation of the slope significantly affected the vegetation pattern. Spatial proximity also influenced the vegetation pattern as a structuring environmental variable or via dispersal constraints. Our results clarify, for the first time, the key variables that drive species distribution and richness across a large altitudinal range within the Atlantic Rainforest. © 2013 Springer Science+Business Media Dordrecht.

Six-year follow-up of maxillary anterior rehabilitation with forced orthodontic extrusion: Achieving esthetic excellence with a multidisciplinary approach

Orthodontic extrusion with multidisciplinary treatment can provide predictable outcomes in selected situations, reducing the costs and the adaptation times of gingival tissues after implant integration. Forced orthodontic extrusion is strongly related to interactions of teeth with their supportive periodontal tissues. This article reports a case of orthodontic extrusion of the maxillary incisors for later implant rehabilitation in a patient with periodontal disease. Slow forces were applied for 14 months. After this time, the teeth were extracted, and the implants were placed on the same day. Also in the same session, the provisional crown was fabricated for restoration of the anterior maxillary interdental papillae loss and for gingival contouring. Clinical and radiographic examinations at the 6-year follow-up showed successful tooth replacement and an improved esthetic appearance achieved by this multidisciplinary treatment. The decision to perform orthodontic extrusion for implant placement in adult patients should be multidisciplinary. Copyright © 2013 by the American Association of Orthodontists.

Connectivity processes and riparian vegetation of the upper Paraná River, Brazil

In fluvial systems, the relationship between a dominant variable (e.g. flood pulse) and its dependent ones (e.g. riparian vegetation) is called connectivity. This paper analyzes the connectivity elements and processes controlling riparian vegetation for a reach of the upper Paraná River (Brazil) and estimates the future changes in channel-vegetation relationship as a consequence of the managing of a large dam. The studied reach is situated 30km downstream from the Porto Primavera Dam (construction finished in 1999). Through aerial photography (1:25,000, 1996), RGB-CBERS satellite imagery and a previous field botany survey it was possible to elaborate a map with the five major morpho-vegetation units: 1) Tree-dominated natural levee, 2) Shrubby upper floodplain, 3) Shrub-herbaceous mid floodplain, 4) Grass-herbaceous lower floodplain and 5) Shrub-herbaceous flood runoff channel units. By use of a detailed topographic survey and statistical tools each morpho-vegetation type was analyzed according to its connectivity parameters (frequency, recurrence, permanence, seasonality, potamophase, limnophase and FCQ index) in the pre- and post-dam closure periods of the historical series. Data showed that most of the morpho-vegetation units were predicted to present changes in connectivity parameters values after dam closing and the new regime could affect, in different intensity, the river ecology and particularly the riparian vegetation. The methods used in this study can be useful for dam impact studies in other South American tropical rivers. © 2012 Elsevier Ltd.

Recolonização de uma área restaurada por morcegos da família Phyllostomidae: padrões de diversidade e uso do espaço

Pós-graduação em Ciências Biológicas (Zoologia) - IBRC

Hydromorphic Soil, Topographic Depression and Vegetation Development History by Using 13c and 14c In Rondônia State (sw Brazilian Amazon)

13C e 14C obtidos da matéria orgânica do solo foram usados para diferenciar fases de flutuação da vegetação em transição floresta-savana. A região apresenta baixos platôs com depressões topográficas imperfeitamente drenadas na superfície. Na topossequência estudada foram analisados solos de cinco perfis localizados sob floresta (F), transição floresta-savana (S1), borda da depressão sob savana (S2) e centro da depressão sob savana (S3). Os valores de 13C e idades evidenciam que a ~ 200cm de profundidade, com idades entre ~ 12.000 e 10.000 A.P., valores de -27‰ a -27,7‰ indicam vegetação de floresta (C3) em todos os perfis. Na profundidade de 100 cm, com idades entre ~ 6.000 e 5.000 A.P., houve enriquecimento de – 20,2‰ a -22,3‰, indicando regressão da floresta e expansão da savana. Valores entre -15,9 e -18,7‰ a 50-60 cm, estimado entre ~ 4.700 a 3.800 A.P., sugere máxima expansão da vegetação C4 em resposta às condições climáticas mais secas, exceto no perfil S3 com valores mais empobrecidos (-20,9‰), sugerindo que na depressão, o desenvolvimento da hidromorfia possibilitou a presença de espécies de gramíneas C3 e C4 da savana em resposta as mudanças das condições ambientais.

Rehabilitation of the Maxillary Arch After Bone Graft Using Immediate Loading With Implant-Supported Fixed Restoration

Moderate and controlled loading environments support or enhance osteogenesis, and, consequently, a high degree of bone-to-implant contact can be acquired. This is because when osteoprogenitor cells are exposed to limited physical deformation, their differentiation into osteoblasts is enhanced. Then, some range of microstrain is considered advantageous for bone ingrowth and osseointegration. The primary stability has been considered one of the main clinical means of controlling micromotion between the implant and the forming interfacial tissue, which helps to establish the proper mechanical environment for osteogenesis. Based on the biological aspects of immediate loading (IL), the objective of this study is to present a clinical case of maxillary arch rehabilitation using immediate loading with implant-supported fixed restoration after bone graft. Ten dental implants were placed in the maxilla 6 months after the autogenous bone graft, removed from the mandible (bilateral oblique line and chin), followed by the installation of an immediate-load fixed cross-arch implant-supported restoration because primary stability was reached for 8 implants. In addition, instructions about masticatory function and how it is related to interfacial micromotion were addressed and emphasized to the patient. The reasons for the IL were further avoidance of an interim healing phase, a potential reduction in the number of clinical interventions for the patient, and aesthetic reasons. After monitoring the rehabilitation for 8 years, the authors can conclude that maxillary IL can be performed followed by a well-established treatment planning based on computed tomography, providing immediate esthetics and function to the patient even when autogenous bone graft was previously performed in the maxilla.

Implants in the zygomatic bone for maxillary prosthetic rehabilitation: a systematic review

The purpose of this systematic review was to evaluate clinical studies on the follow-up survival of implants inserted in the zygomatic bone for maxillary rehabilitation. A comprehensive search of studies published from 2000 to July 2012 and listed in the PubMed/MEDLINE, Embase, and Cochrane Library databases was performed in accordance with the PRISMA statement. Relevant studies were selected according to predetermined inclusion and exclusion criteria. The initial database search yielded 751 titles. After filtering, 313 abstracts were selected, culminating in 42 full text articles. Application of eligibility criteria led to the elimination of 17 articles. Hence 25 full-text articles were considered clinically relevant and were included. Calculations of the interval survival rates and cumulative survival rates of implants could be carried out on the data extracted from the final list of included studies for the different time intervals. These studies reported the insertion of a total of 1541 zygomatic implants and 33 implant failures. Failure generally occurred during the first year interval and was related to clinical complications, such as recurrent acute and chronic sinusitis. After a 36-month follow-up, the survival rate was 97.86%. Additional studies with longer follow-up periods, including the number of zygomatic implants inserted and details of the variations in the surgical techniques used and the impact of the maxillary morphology are still required.

Use of Stress Analysis Methods to Evaluate the Biomechanics of Oral Rehabilitation With Implants

Because the biomechanical behavior of dental implants is different from that of natural tooth, clinical problems may occur. The mechanism of stress distribution and load transfer to the implant/bone interface is a critical issue affecting the success rate of implants. Therefore, the aim of this study was to conduct a brief literature review of the available stress analysis methods to study implant-supported prosthesis loading and to discuss their contributions in the biomechanical evaluation of oral rehabilitation with implants. Several studies have used experimental, analytical, and computational models by means of finite element models (FEM), photoelasticity, strain gauges and associations of these methods to evaluate the biomechanical behavior of dental implants. The FEM has been used to evaluate new components, configurations, materials, and shapes of implants. The greatest advantage of the photoelastic method is the ability to visualize the stresses in complex structures, such as oral structures, and to observe the stress patterns in the whole model, allowing the researcher to localize and quantify the stress magnitude. Strain gauges can be used to assess in vivo and in vitro stress in prostheses, implants, and teeth. Some authors use the strain gauge technique with photoelasticity or FEM techniques. These methodologies can be widely applied in dentistry, mainly in the research field. Therefore, they can guide further research and clinical studies by predicting some disadvantages and streamlining clinical time.

Mechanical behavior of dental implants in different positions in the rehabilitation of the anterior maxilla

Statement of problem. In dental rehabilitations that involve implants, the number of implants is sometimes smaller than the number of lost teeth. This fact can affect the biomechanical behavior and success of the implants.Purpose. The purpose of this study was to investigate the mechanical behavior of different implant positions in the rehabilitation of the anterior maxilla.Material and methods. Three-dimensional models of the maxilla were created based on computed tomography images for 3 different anterior prosthetic rehabilitations. In group IL, the implants were placed in the lateral incisor positions with pontics in the central incisor positions; in group IC, the implants were in the central incisor positions with cantilevers in the lateral incisor positions; and, in group ILIC, one implant was in a lateral incisor position and one was in a central incisor position, with a pontic and a cantilever in the remaining positions. A 150 N load was distributed and applied at the center of the palatal surface of each tooth at a 45-degree angle to the long axis of the tooth. The resulting stress-strain distribution was analyzed for each group.Results. The lowest displacement of the prosthetic structure was observed in group IC, although the same group exhibited the largest displacement of the bone tissue. In the bone tissue, the von Mises stress was mainly observed in the cortical bone in all groups. The maximum value of the von Mises stress shown in the cortical tissue was 35 MPa in the implant that neighbors the cantilever in group ILIC. The maximum von Mises stress in the trabecular bone was 3.5 MPa.Conclusion. The prosthetic configuration of group IC limited the displacement of the prosthetic structure but led to greater displacement of the bone structure. The use of a cantilever increased the stress concentration in the implant and in the bone structure adjacent to the cantilever under the conditions studied here.