Abrasion resistance of direct and indirect resins as a function of a sealant veneer

Abrasive wear is one of the most common type of wear that not only affect teeth, as also dental restorations. Thus to investigate one of the etiological factors as tooth brushing procedure is clinical relevant in order to select the best material combination that may prevent damage of resin dental restoration's abrasion. This study evaluated the influence of tooth brushing on mass loss and surface roughness of direct Venus (Vs) and indirect Signum (Sg) resin composites, with and without a surface sealant, Fortify (F). Twenty-four specimens were prepared with each resin composite, using their proprietary curing units, according to manufacturer's instructions. All the specimens were polished and ultrasonically cleaned in distilled water for 5 minutes. Half of the specimens of each resin (n = 12) were covered with F (Vs F and Sg F ), except for the control (C) specimens (Vs C and Sg C ), which were not sealed. Mass loss (ML) as well as surface roughness (Ra ) was measured for all the specimens. Then, the specimens were subjected to toothbrush-dentifrice abrasion, using a testing machine for 67.000 brushing strokes, in an abrasive slurry. After brushing simulation, the specimens were removed from the holder, rinsed thoroughly and blot dried with soft absorbent paper. The abrasion of the material was quantitatively determined with final measurements of ML and surface roughness, using the method described above. ML data were analyzed by two-way analysis of variance (ANOVA) and the analysis indicated that resin composites were not statistically different; however, the specimens sealed with F showed higher ML. Ra mean values of the groups Vs F and Sg F significantly increased. Tooth brushing affects mainly the roughness of the direct and indirect resin composites veneered with a sealant.

Saúde bucal e educação infantil: avaliação do desgaste e do acondicionamento de escovas dentárias utilizadas por pré-escolares

Introduction: Early childhood is an essential phase of life for the future of oral health. The link between educational and health sectors can facilitate incorporating educational and preventive oral health practices in daily teaching in pre-schools. The main measure is manual tooth-brushing, which is the most accessible method for most of the population. Objective: The objective of this study is to evaluate macroscopically the wear on the bristles, form of storage, and identification of tooth brushes. Material and method: 345 toothbrushes used by children between the ages of 2 and 5 were evaluated in 4 pre-schools, by 2 participants from the oral health program. The Rawls et al. index was used to evaluate the bristles. Result: There were statistically significant differences (p = 0.020 - Mann-Whitney U test) between the frequency of toothbrushes, with the highest being (n = 205) stored at participating school; and, between adequate and inadequate brushes (p < 0.05 - X2 test) with 31.7 and 60%, respectively, classified as unfit for tooth-brushing. Of the toothbrush holders evaluated 100% were used collectively. Regarding identification, 18% of the toothbrushes were not identified in participating schools, and 37% in the others. Conclusion: The toothbrushes exhibited marked wear, and storage was inadequate; however, the schools participating in the oral health program showed toothbrushes with bristles less worn. It is suggested that training of educators regarding correct storage and evaluation of toothbrushes for wear of the bristles should be undertaken in all early childhood schools.

Abrasive wear of two glass ionomer cements after simulated toothbrushing

Introduction and objective: Glass ionomer cement, which was first introduced in Dentistry in 1972, presents good qualities such as aesthetics, fluoride release and adhesion to dental tissues. Because of its preventive characteristics regarding to dental caries, glass ionomer cement has been used for Atraumatic Restorative Treatment (ART), as reported by Frencken and Holmgren [6], meeting the principles announced by the World Health Organization (WHO) for application to large population groups without regular access to dental care. Material and methods: In this present study, the abrasive wear strength of two glass-ionomer cements (Vidrion R® and ChemFlex®) was evaluated through toothbrushing machine. Classic® toothbrushes with soft bristles and Sorriso® dentifrice were also used for the study. Results: Student-t test showed significant difference between both groups, with tobs value = 9.4411 at p < 0.05. Conclusion: It can be concluded that the wear rate caused by toothbrush/dentifrice was higher for Vidrion R® (52.00 mg) than ChemFlex® (5.57 mg).

Utilização das tecnologias assistidas na concepção, no desenvolvimento e no projeto de uma escova dental sustentável e ergonômica

The toothbrush is identified as one of the most importants inventions in human history. Most of them are made by polypropylene, a recyclable polymer. Some are made of polypropylene and polyethylene leftovers from others industrial processes. However, the toothbrushes are discarded incorrectly and end up in landfills, which could be avoided by using a material and design suitable for the manufacture of the product. This study aimed, based on research, develop and design a toothbrush model with great features. For the conception of the prototype, was used rapid prototyping technologies. With the intention of improving the product quality, was created an ergonomic, sustainable and environmentally friendly model, seeking maximally reduce the generation of waste and environmental damages. The solution adopted was the use of "interchangeable head", which can be discarded after their useful life, keeping the rest of the body.