Anti-erosive properties of solutions containing fluoride and different film-forming agents

Objectives: To evaluate the anti-erosive potential of solutions containing sodium fluoride (NaF, 225 ppm F) and different film-forming agents.Methods: In Phase 1, hydroxyapatite crystals were pre-treated with solutions containing NaF (F), linear sodium polyphosphate (LPP), sodium pyrophosphate tetrabasic (PP), sodium tripolyphosphate (STP), sodium caseinate (SC), bovine serum albumin (BSA), stannous chloride (Sn) and some combinations thereof. Deionized water was the control (C). The pH-stat method was used to evaluate hydroxyapatite dissolution. In Phase 2, the most effective solutions were tested in two independent experiments. Both consisted of an erosion-remineralization cycling model using enamel and dentine specimens with three solution treatments per day. In Phase 2a, the challenge was performed with 0.3% citric acid (pH = 3.8). In Phase 2b, 1% citric acid (pH = 2.4) was used. Hard tissue surface loss was determined profilometrically. Data were analyzed with two-way ANOVA and Tukey tests.Results: In Phase 1, F, LPP, Sn and some of their combinations caused the greatest reduction in hydroxyapatite dissolution. In Phase 2a, C showed the highest enamel loss, followed by LPP. There were no differences between all other groups. In Phase 2b: (F + LPP + Sn) < (F + LPP) = (F + Sn) < (F) = (LPP + Sn) < (LPP) < (Sn) < C. For dentine, in both experiments, only the fluoride-containing groups showed lower surface loss than C, except for LPP + Sn in 2a.Conclusions: F, Sn, LPP reduced enamel erosion, this effect was enhanced by their combination under highly erosive conditions. For dentine, the F-containing groups showed similar protective effect.Clinical significance: The addition of LPP and/or Sn can improve the fluoride solution protection against erosion of enamel but not of dentine. (C) 2015 Elsevier Ltd. All rights reserved.

Preparação e caracterização de novos híbridos orgânicos-inorgânicos baseados em carboximetilcelulose/polifosfato de sódio dopados com 'Eu'Cl IND.3

Organic- inorganic hybrid (HOI) are materials prepared with the combination of inorganic and organic components. The properties of a hybrid material are unique, not being the sum of each individual component added. This occurs because there is a synergism that depends of the chemical nature of organic and inorganic components, of the size and morphology of their domains. The sodium carboxymethylcellulose (CMC) it's an anionic polymer obtained of the cellulose, very soluble in water in which forms both solutions themselves and gels. The sodium polyphosphate (NaPO3)n, known commercially as Graham Salt is the only polyphosphate soluble in water, and it's the polyphosphate with the longest chain. At the present work it was prepared and characterized new phosphate organic- inorganic hybrids films of carboxymethylcellulose / sodium phosphate and luminescent films of CMC/NaPO3 doped with europium chloride (EuCl3). The films where prepared in several proportions. At first, it was set the amount of water to be used and the amount of carboxymethylcellulose, changing the concentrations of sodium polyphosphate and europium chloride. After pre-establishing concentrations, for each film, the components were submitted to constant agitation and subsequent drying. The inorganic-organic hybrid films were characterized by, TG, DR-X, DMA, FT-IR, UV-Vis-NIR, RMN 31P e 13C and at last, a study of luminescence was made. The hybrid films obtained are transparent and macroscopically homogeneous, however, the MET measures showed the formation of micro-islands of polyphosphate along the material, this fact indicates a bigger fragmentation of the films and this is verified by DMA analysis which shows a smaller resistance of the film with the increase of the concentration of phosphate. Both spectrum FT-IR and RMN analysis of the films, don't show the formation of new bands of their precursors, CMC e NaPO3,....

Avaliação in vitro de superfícies de titânio irradiadas com laser de Er,Cr:YSGG

Introduction: As a new alternative in the complementary treatment lasers teem different systems were employed in the decontamination of dental surfaces implants however, some systems have caused significant changes in its surface. Purpose: Analyze by Scanning Electron Microscopy (SEM) the effects of laser irradiation of Er,Cr: YSGG on different surfaces of titanium. Material and method: Study of 20 titanium discs, and 10 Machined Surface (MS) and 10 surfaces treated with acid (AC). The 10 discs with the same treatment were divided into two groups with five units each, the irradiation was performed in powers of 1 W and 2 W. Result: Showed that the irradiation with 1 W of power resulted in no significant morphological changes in the MS-irradiated compared to non-irradiated surfaces. In MS surfaces, minor changes were observed in the increase of 1000× when compared to non-irradiated surface. With 2 W of power, there were no significant morphological changes in the MS, compared to non-irradiated areas. In AC some changes were observed in the increase of X 1000, showing areas of wear suggestive of treatment and some areas with melting point. Conclusion: Considering the results and the parameters used in this study it was concluded that the Er, Cr: YSGG irradiation can be used for the machined surfaces of implants, but in acid-treated surfaces irradiation parameters should be more controlled.

Estudo de microscopia eletronica de varredura e transmissão de pregas vocais de idosos

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)