Structural and optical properties of brominated plasma polymers

Novel brominated amorphous hydrogenated carbon (a-C:H:Br) films were produced by the plasma polymerization of acetylene-bromoform mixtures. The main parameter of interest was the degree of bromination, which depends on the partial pressure of bromoform in the plasma feed, expressed as a percentage of the total pressure, R-B. When bromoform is present in the feed, deposition rates of up to about 110 nm min(-1) may be obtained. The structure and composition of the films were characterized by Transmission Infrared Reflection Absorption Spectroscopy (IRRAS) and X-ray Photo-electron Spectroscopy (XPS). The latter revealed that films with atomic ratios Br:C of up to 0.58 may be produced. Surface contact angles, measured using goniometry, could be increased from similar to 63 degrees (for an unbrominated film) to similar to 90 degrees for R-B of 60 to 80%. Film surface roughness, measured using a profilometer, does not depend strongly on R-B. Optical properties the refractive index, n, absorption coefficient, alpha(E), where E is the photon energy, and the optical gap, E-g, were determined from film thicknesses and data obtained by Transmission Ultraviolet-Visible Near Infrared Spectroscopy (UVS). Control of n was possible via selection of R-B. The measured optical gap increases with increasing F-BC, the atomic ratio of Br to C in the film, and semi-empirical modeling accounts for this tendency. A typical hardness of the brominated films, determined via nano-indentation, was similar to 0.5 GPa. (C), 2013 Elsevier B.V. All rights reserved.

Different fasting periods in tiletamine-zolezepam-anethetized cats: Glycemia, recovery, blood-gas and cardiorrespiratory parameters

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

The effects of different inspired oxygen fractions on gas exchange and Tei-index of myocardial performance in propofol-anesthetized dogs

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Efeito de hipercabia no desenvolvimento de ovos de Trachemys scripta

Females of the painted turtle, Trachemys scripta, have an annual reproductive cycle. Their nest periods in Brazil starts around September and they lay about 7 - 10 eggs in nests dug in the soil. The eggs hatch in December. It is possible that the nest cover cause problems for the gas diffusion, also, the rain can wet or compact the soil covering the nest, or even soaked the whole area. Those problems may change the nests intern atmosphere decreasing O2 partial pressure (hypoxia) and increasing CO2 partial pressure (hypercarbia). The main objective of this study was to determine if and how hypercarbia (3% and 6%CO2), could influence the eggs and early posthatching development of the Trachemys scripta. We used three experimental groups of eggs incubated in: normal atmosphere (Control group CG, n = 14), hypercarbia with 3% of CO2 (G3%, n = 16) and with 6% of CO2 (G6%, n = 15). The profile of the mass increment during the egg development were not different among the groups, GC = 9.89±0.81g; G3% = 10.11±0.60g and G6% = 10.58±0.36g. In addition, the mass of the post-hatching turtles were the not different. There were not differences between the duration of the incubation period among the experimental groups, GC = 60.12±0.97days, G3% = 59.00±0.98days and G6% = 60.80±1.14days. The mortality rates were not affected by the hypercarbia, GC = 0.43 (43%), G3% = 0.27 (27%) and G6% = 0.37 (37%). Furthermore, the mass increment and the metabolic rate were the same among the early development of the turtles until 3 month after hatching. We conclude that hypercarbia (up to 6% of CO2) does not cause any alteration on the eggs or post-hatching normal development. It is possible that the combination of hypercarbia and hypoxia change those results

Alterações metabólicas e morfométricas induzidas por hipóxia em Gallus gallus

Pós-graduação em Zootecnia - FCAV

Efeitos da infusão contínua de tiopental ou propofol em coelhos mantidos em respiração espontânea

Pós-graduação em Cirurgia Veterinária - FCAV

Achados clínicos, hemodinâmicos e hemogasométricos da infusão contínua de propofol associado ou não ao tramadol em ovelhas submetidas à videolaparoscopia

Pós-graduação em Cirurgia Veterinária - FCAV

The calcium looping cycle study for capturing carbon dioxide applied to the energy generation

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Pyrolysis, combustion and oxy-combustion studies of sugarcane industry wastes and its blends

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Evaluation of the vitality of nelore calves born of normal or dystocic parturitions

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Vacuum infiltration of copper aluminate by liquid aluminium

This paper studies attained microstructures and reactive mechanisms involved in vacuum infiltration of copper aluminate preforms with liquid aluminium. At high temperatures, under vacuum, the inherent alumina film enveloping the metal is overcome, and aluminium is expected to reduce copper aluminate, rendering alumina and copper. Under this approach, copper aluminate toils as a controlled infiltration path for aluminium, resulting in reactive wetting and infiltration of the preforms. Ceramic preforms containing a mixture of Al2O3 and CuAl2O4 were infiltrated with aluminium under distinct vacuum levels and temperatures, and the resulting reaction and infiltration behaviour is discussed. Copper aluminates stability ranges depend on vacuum level and oxygen partial pressure, which determine both CuAl2O4 and CuAlO2 ability for liquid aluminium infiltration. At 1100 °C and 0.76 atm vacuum level CuAl2O4 is stable, indicating pO2 above 0.11 atm. Reactive infiltration is achieved via reaction between aluminium and CuAl2O4; however, fast formation of an alumina film blocking liquid aluminium wicking results in incipient infiltration. At 1000 °C and 3.8 × 10−7 atm vacuum level, CuAlO2 decomposes to Cu and Al2O3 indicating a pO2 below 6.0 × 10−7 atm; infiltration of the ceramic is hindered by the non-wetting behaviour of the resulting metal alloy. At 1000 °C and 1.9 × 10−6 atm vacuum level CuAlO2 is stable, indicating pO2 above 6.0 × 10−7 atm. Extensive infiltration is achieved via redox reaction between aluminium and CuAlO2, rendering a microstructure characterised by uniform distribution of alumina particles amid an aluminium matrix. This work evidences that liquid aluminium infiltration upon copper aluminate-rich preforms is a feasible route to produce Al–matrix alumina-reinforced composites. The associated reduction reaction renders alumina, as fine particulate composite reinforcements, and copper, which dissolves in liquid aluminium contributing as a matrix strengthener.

Efeitos da interação da doxiciclina e adrenomedulina na embolia pulmonar aguda em ovinos anestesiados

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Efeitos da estabulação sobre o trato respiratório de equinos em dois tipos diferentes de camas e a pasto

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)