Utilization of Minimum Quantity Lubrication (MQL) with Water in CBN Grinding of Steel

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Evaluation of different methods of cooling-lubrication in cylindrical grinding of advanced ceramic dip

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Utilização da mínima quantidade de lubrificante (MQL) com água no processo de retificação cilíndrica em cerâmica avançada com rebolo de ligante resino cerâmico/metálico

Pós-graduação em Engenharia Mecânica - FEB

Análise térmica do processo de retificação plana sob diferentes condições de lubrificação utilizando técnicas de transferência de calor reversa

Pós-graduação em Ciência e Tecnologia de Materiais - FC

Hot turning of a difficult-to-machine steel (sae xev-f) aided by infrared radiation

A possible way for increasing the cutting tool life can be achieved by heating the workpiece in order to diminish the shear stress of material and thus decrease the machining forces. In this study, quartz electrical resistances were set around the workpiece for heating it during the turning. In the tests, heat-resistant austenitic alloy steel was used, hardenable by precipitation, mainly used in combustion engine exhaustion valves, among other special applications for industry. The results showed that in the hot machining the cutting tool life can be increased by 340% for the highest cutting speed tested and had a reduction of 205% on workpiece surface roughness, accompanied by a force decrease in relation to conventional turning. In addition, the chips formed in hot turning exhibited a stronger tendency to continuous chip formation indicating less energy spent in material removal process. Microhardness tests performed in the workpieces subsurface layers at 5 m depth revealed slightly higher values in the hot machining than in conventional, showing a tendency toward the formation of compressive residual stress into plastically deformed layer. The hot turning also showed better performance than machining using cutting fluid. Since it is possible to avoid the use of cutting fluid, this machining method can be considered better for the environment and for the human health.

Estudo da usinagem por torneamento de ligas de alumínio

The non-ferrous materials have got so many mechanical, physical and chemical advantageous properties so that is provided to them consolidated position in industry. In this context, aluminium alloys have been seen a lot on many applications of engineering areas – specially on automotive, aeronautical and aerospace due to their main properties such as low density, high corrosion resistance, favorable structure weight / material resistance relation, among others characteristics that are mencioned through this study. This study aims to analyze the aluminium alloys behavior on a general context when they are used on turning process, taking for examples the 6262 and 7050 aluminium alloys. In this way, the analysis studies the datas obtained during the turning tests realized on 3 steps each one; those datas are concerning the medium and total rugosities – obtained with the assistance of a portable Surface Roughness Finish Tester, as well as the chips obtained during the tests - visual analysis, and the cutting tools wear – with the assistance of an optical microscope, under different conditions of application of cutting fluids (dry machining, application of coolant in abundance and MQL – Minimum Quantity of Lubricant). The results concerning this study show detailed information about influence of cutting fluids on the machining by turning of the aluminium alloys related on this work and also about aluminium alloys in general when they are used on turning processes with different conditions from one another. By this way, it was evident the MQL technique is the best one for the 6262 alloy. However, for 7050 alloy, it was evident that the dry machining is responsible for the best results

Estudo da influência da aplicação do fluido de corte no torneamento da liga de alumínio AA7075

One of the ways to minimize the effects of unproductive time caused by tool wear can be achieved by introducing an efficient system of lubrication and cooling in the process. However, in the last decade the research had the goal to restrict the maximum use of refrigerants and / or lubricants in metal-mechanical production. The important factors that justify this procedure include the operational costs of production, ecological issues, and the legal requirements of environmental conservation and preservation of human health. The purpose of the proposed work is the study of machining by turning with the focus on the influence caused by the application of cutting fluid in several ways of application (abundant and MQF) and also by comparing the results obtained by machining without the presence of fluid . For this purpose, the turning tests are conducted using an aluminum alloy (AA 7075). The response variables to be analyzed were obtained from the roughness (Ra and Ry), the stresses presented (VB) and their progression in relation to the cutting length achieved, the type of chip formed, in addition to changes in the degree of finish (roughness) presented by the turned parts. The results of this study should provide more detailed information about the actual influence of cutting fluids in turning this alloy, which are characterized by high rates of deformation when the formation of damaging your chip machining and also the quality of surface generated. Therefore, it is expected to provide subsidies to promote the optimization of machining this alloy making the most of the role of cutting fluid

Estudo sobre fornos de tratamento térmico e propostas de cogeração de energia em usina siderurgica não integrada

Steel industry is a sector heavily dependent on energy, both electrical and thermal. Since the receipt of raw materials to the shipment of finished products to customers, through mergers, casting, rolling, heat treatment, inspection, among others, high amounts of energy are demanded, generating very significant costs to the productive chain in its entirety . Therefore, any alternative that favors the reduction in energy consumption or barateie the cost of this is very welcome. Within this context, this paper aims to make a technical and economic analysis of installing a cogeneration plant in the field rolling in a non-integrated steel mill. Two configurations are proposed plants, with one being the use of heat from waste gases from furnaces existing in the area mentioned and another with the use of heat from waste gases from an internal combustion engine. Both proposals are evaluated technically and later is done the economic analysis, calculating the financial return (pay back) in relation to the investment required, operation and maintenance of the plant

Sistemas de filtragem aplicados em processos fabris automotivos

The present work resulted from a study about coolant filtration systems in industries with metalworking process in large scale. The filtration and element filter world markets move billions of Reais per year and have a promissory future considering that with the global requirements of sustainable economic development, many companies invest in new filtering technology. Either known as coolant or cutting fluid, it is used to lubricate e cool parts during machining and is necessary due to the high volume demanded in the several machining operations and to the high cost of the product. Therefore, there is the need for recycling the product after its use. The work shows the technology and fundamentals of filtration as well as different filtering elements, filtration systems and scale contamination used in the industry. Also, there is a differentiation between filtration of the surface type (cake) and depth filtration and shows the basic theory of filtration by mathematic models in different operational conditions. Ultimately, project criteria for a coolant filtration system selection is shown followed by technical-operational details of a real vacuum filtration system and a case study aiming the operational cost reduction of the system

Usinabilidade e integridade superficial de implantes dentários

Pós-graduação em Engenharia Mecânica - FEIS

Análise comparativa dos métodos MQL, MQL/Água e convencional na retificação cilíndrica do aço ABNT 52100, com rebolo de óxido de alumínio

Pós-graduação em Engenharia Mecânica - FEB

Estudo da aplicação de mínima quantidade de fluido no fresamento de acabamento da liga Ti-6Al-4V

Pós-graduação em Engenharia Mecânica - FEG

A study on the viability of minimum quantity lubrication with water in grinding of ceramics using a hybrid-bonded diamond wheel

With the currently strict environmental law in present days, researchers and industries are seeking to reduce the amount of cutting fluid used in machining. Minimum quantity lubrication is a potential alternative to reduce environmental impacts and overall process costs. This technique can substantially reduce cutting fluids in grinding, as well as provide better performance in relation to conventional cutting fluid application (abundant fluid flow). The present work aims to test the viability of minimum quantity lubrication (with and without water) in grinding of advanced ceramics, when compared to conventional method (abundant fluid flow). Measured output variables were grinding power, surface roughness, roundness errors and wheel wear, as well as scanning electron micrographs. The results show that minimum quantity lubrication with water (1:1) was superior to conventional lubrication-cooling in terms of surface quality, also reducing wheel wear, when compared to the other methods tested.

Efeito das diferentes direções de aplicação de jato de fluido de corte no torneamento de um aço de difícil usinagem

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Leaf-cutting ant faecal fluid and mandibular gland secretion: effects on microfungi spore germination

The mandibular gland secretion (MGS) and the faecal fluid (FF) of the leaf-cutting ant Atta sexdens rubropilosa Forel affected the spore germination of selected microfungi isolated from nests of this insect. MGS was more effective than the FF, completely inhibiting the spore germination of four out of six microfungi species.