Use of Stress Analysis Methods to Evaluate the Biomechanics of Oral Rehabilitation With Implants

Because the biomechanical behavior of dental implants is different from that of natural tooth, clinical problems may occur. The mechanism of stress distribution and load transfer to the implant/bone interface is a critical issue affecting the success rate of implants. Therefore, the aim of this study was to conduct a brief literature review of the available stress analysis methods to study implant-supported prosthesis loading and to discuss their contributions in the biomechanical evaluation of oral rehabilitation with implants. Several studies have used experimental, analytical, and computational models by means of finite element models (FEM), photoelasticity, strain gauges and associations of these methods to evaluate the biomechanical behavior of dental implants. The FEM has been used to evaluate new components, configurations, materials, and shapes of implants. The greatest advantage of the photoelastic method is the ability to visualize the stresses in complex structures, such as oral structures, and to observe the stress patterns in the whole model, allowing the researcher to localize and quantify the stress magnitude. Strain gauges can be used to assess in vivo and in vitro stress in prostheses, implants, and teeth. Some authors use the strain gauge technique with photoelasticity or FEM techniques. These methodologies can be widely applied in dentistry, mainly in the research field. Therefore, they can guide further research and clinical studies by predicting some disadvantages and streamlining clinical time.

Fatigue Behavior of Weld Repaired AISI 4130 Aeronautic Steel Used in Critical Flight Safety Structures

Since the 1950s, fatigue is the most important project and operational consideration for both civil and military aircrafts. For some aircraft models the most loaded component is one that supports the motor: the Motor Cradle. Because they are considered critical to the flight safety the aeronautic standards are extremely rigorous in manufacturing them by imposing a zero index of defects on the final weld quality (Safe Life), which is 100% inspected by Non-Destructive Testing/NDT. This study has as objective to evaluate the effects of up to four successive TIG welding repairs on the axial fatigue strength of an AISI 4130 steel. Tests were conducted on hot-rolled steel plate specimens, 0.89 mm thick, with load ratio R = 0.1, constant amplitude, at 20 Hz frequency and in room temperature, in accordance with ASTM E466 Standard. The results were related to microhardness and microstructural and geometric changes resulting from welding cycles.

Citrus pulp and enzyme complex for growing and finishing pigs

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Fullerenes generated from porous structures

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Improvement to the physical quality and imbibition pattern in seeds of candeia (Eremanthus incanus (Less.) Less.)

The objective of this work was to develop a methodology for seed processing and X-ray analysis and to study imbibition pattern in seeds of candeia (Eremanthus incanus). Seeds were gathered in 2001 and 2002 in Morro do Pilar and Lavras respectively, processed and stored in a cold chamber (5ºC/60%RH) until the start of experiments. In order to identify unfilled seeds, a protocol was developed for X-ray use combining radiation energy (Kv) and exposure time (seconds). For elimination of unfilled seeds, an experiment was conducted using a South Dakota seed blower whereby different opening settings and ventilation times were combined. Original seed lots and categorized lots following radiograph viewing were tested by germination tests, with seeds being cleansed in sodium hypochlorite and scattered over blotting paper in 'gerboxes' and then taken to germinators with alternating temperatures of 20º-30ºC and 10 hours of light, for up to 15 days. Imbibition curves were determined under the conditions 30ºC, 20º-30ºC/10 hours of light and 30º-20ºC/10 hours of light. The X-ray protocol that best allowed viewing of internal seed structures was 30Kv for 45 seconds. Seed separation using the blower setting at a 3.0 opening for 30 seconds raised the number of embryonic seeds to values exceeding 99%, also raising the germination rates as a consequence. The imbibition pattern is three-phased and the germination process is completed in 72 hours. Under alternate temperatures, primary root growth is favored.

Description of three new species of Moenkhausia (Teleostei, Characiformes, Characidae) with the definition of the Moenkhausia jamesi species complex

From the examination of extensive comparative material currently identified as M. jamesi we verified that there are, at least, three new species under this name. These, along with M. jamesi and M. justae, form what we herein called the M. jamesi species complex, by sharing the following group of characters: a short maxilla, with its distal margin not exceeding anterior third of the second infraorbital; first through third teeth of the inner row of premaxilla and first and second dentary teeth with cusps arranged in a pronounced arch, humeral spot positioned between the fourth and seventh scales of the lateral line and extending up to four scale rows above the lateral line and one scale row below the lateral line, and a vertically oval to round spot at the base of the caudal fin rays. Moenkhausia ischyognatha sp. n., from Rio Xingu basin, differs from the other species of the complex by its lower head depth. Moenkhausia alesis sp. n., from the river system Tocantins-Araguaia, differs from M. jamesi, M. ischyognatha, and M. sthenosthoma by the number of scale rows above the lateral line. Moenkhausia sthenosthoma sp. n., from the Rio Madeira basin, differs from M. jamesi by the number of scale rows between the lateral line and the midventral scale series. Moenkhausia justae can be diagnosed from the other species of the complex by having a tri to pentacuspidate tooth on the maxilla.

Sistemática e filogenia do fungo parasita Escovopsis associado às formigas Attini

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Anatomia floral e ontogenia de espécies dímeras de Paepalanthus Mart. (Eriocaulaceae, Poales) e seu significado evolutivo

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)