Influence of the substitution of Y2O3 for CeO2 on the mechanical and microstructural properties of silicon nitride

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Mechanical properties, hydrophilicity and water activity of starch-gum film: effect of additives and deacetylated xanthan gum

The effect of deacetylated xanthan gum, additives (sucrose, soybean oil, sodium phosphate and propylene glycol) and pH modifications on mechanical properties, hydrophilicity and water activity of cassava starch-xanthan gum films has been studied. Sucrose addition resulted in the highest effect observed on cassava starch films elongation at break. The deacetylated xanthan gum had higher effect on elongation at break when comparing to the acetylated gum, although both gums presented an inferior effect in relation to the obtained with sucrose. However, when comparing to the control and PVC films, lower tensile strength resistance values were observed when adding sucrose. Increased water activity was observed for films added with sucrose, thus, increasing the material biodegradation. Sucrose and deacetylated xanthan gum addition resulted in a slight hydrophilicity increase. (C) 2004 Elsevier Ltd. All rights reserved.

Chemical composition of flavonoids and styrylpyrones and the genetic variability of isozymes in natural populations of Cryptocarya mandioccana Meisner (Lauraceae)

The chemical composition of leaves of 57 trees of Cryptocarya mandioccana from three populations of southeastern Brazil was investigated through HPLC, assaying six flavonoids, seven styrylpyrones, and seven unidentified compounds. From 51 of the former trees, genotypes were obtained from 40 polymorphic loci of 19 isozymes. Cluster analyses of the phytochemical and genetical variation revealed that trees exhibited four chemotypes and five clusters from isozymes, respectively. Discriminant analyses from selected variables of the isozymic and chemical data sets were performed, respectively, in relation to the four chemotypes and the five isozyme clusters. The classification of individuals presented respective error estimates of 9.16% and 13.57%, indicating that the genetic data could explain the clusters from chernotypes and vice versa at acceptable error levels. Linear regressions with Dummy variable showed significant association of locus Skdh-2 with quercetin-3-O-beta-D-glucopyranoside and cryptofolione, indicating that its alleles would be responsible for the chemotype variation between individuals. (c) 2006 Elsevier Ltd. All rights reserved.

Effects of displacement and trajectory length on the variability pattern of reaching movements

The design of the present study enabled the authors to distinguish between the possible effects of movement displacement and trajectory length on the pattern of final positions of planar reaching movements. With their eyes closed, 9 subjects performed series of fast and accurate movements from different initial positions to the same target. For some series, the movements were unconstrained and were therefore performed along an approximately straight vertical line. For other series, an obstacle was positioned so that trajectory length was increased because of an increase in movement curvature. Ellipses of variability obtained by means of principal component analysis applied to the scatter of movement final positions enabled the authors to assess the pattern of movement variable errors. The results showed that the orientation of the ellipses was not affected by movement displacement or by trajectory length, whereas variable errors increased with move ment displacement. An increase in trajectory length as a consequence of increased curvature caused no change in variable error. From the perspective of current motor control theory, that finding was quite unexpected. Further studies are required so that one can distinguish among the possible effects of various kinematics, kinetics, and other variables that could affect the pattern of variable errors of reaching movements.

Expression and variability of molecular chaperones in the sugarcane expressome

Molecular chaperones perform folding assistance in newly synthesized polypeptides preventing aggregation processes, recovering proteins from aggregates, among other important cellular functions. Thus their study presents great biotechnological importance. The present work discusses the mining for chaperone-related sequences within the sugarcane EST genome project database, which resulted in approximately 300 different sequences. Since molecular chaperones are highly conserved in most organisms studied so far, the number of sequences related to these proteins in sugarcane was very similar to the number found in the Arabidopsis thaliana genome. The Hsp70 family was the main molecular chaperone system present in the sugarcane expressome. However, many other relevant molecular chaperones systems were also present. A digital RNA blot analysis showed that 5'ESTs from all molecular chaperones were found in every sugarcane library, despite their heterogeneous expression profiles. The results presented here suggest the importance of molecular chaperones to polypeptide metabolism in sugarcane cells, based on their abundance and variability. Finally, these data have being used to guide more in deep analysis, permitting the choice of specific targets to study. (c) 2006 Elsevier GmbH. All rights reserved.

Spatial variability of soil attributes and sugarcane yield in relation to topographic location

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Fiber Post Cementation Strategies: Effect of Mechanical Cycling on Push-out Bond Strength and Cement Polymerization Stress

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Invited review Giardia duodenalis: Inter-strain variability of proteins, antigens, proteases, isoenzymes and nucleic acids

Giardia duodenalis isolates from asymptomatic or symptomatic patients and from animals present similarities and differences in the protein composition, antigenic profile, pattern of proteases and isoenzymes, as well as in nucleic acids analysis. In the present overview, these differences and similarities are reviewed with emphasis in the host-parasite interplay and possible mechanisms of virulence of the protozoon.

Genetic variability of Brazilian strains of the Microcystis aeruginosa complex (Cyanobacteria/Cyanophyceae) using the phycocyanin intergenic spacer and flanking regions (cpcBA)

The genetic and morphological variability among 15 Brazilian strains of Microcystis aeruginosa (Kütz.) Kütz. collected from four locations was examined and compared with several reference strains of M. aeruginosa, M. viridis (A. Br.) Lemm. and M. wesenbergii (Kom.) Kom. in Kondr. Brazilian strains were classified by morphological features and by comparison of the nucleotide sequences of the cpcBA intergenic spacer and flanking regions. Our results indicate that Brazilian strains classified as M. aeruginosa are phylogenetically diverse compared with reference strains of M. aeruginosa and that the current taxonomy underestimates genetic diversity within M. aeruginosa. The data also demonstrate that morphological criteria alone are inadequate to characterize Microcystis species. Although colonial characters were shown to vary considerably in culture, some genetic lineages demonstrated consistent cellular diameter ranges, indicating that cell size has value as a taxonomic character. The detection of six M. aeruginosa genotypes in a single water body indicates that morphological approaches can also seriously underestimate the diversity of Microcystis bloom populations.

Morphological, mechanical and rheological properties of nylon 6/acrylonitrile-butadiene-styrene blends compatibilized with MMA/MA copolymers

The morphological, mechanical and rheological properties of nylon 6/acrylonitrile-butadiene-styrene blends compatibilized with MMA-MA [poly(methyl methacrylate-comaleic anhydride)] copolymers were studied. A twin screw extruder was used for melt-blended the polymers and the injection moulding process was used to mold the samples. The main focus was on nylon 6/ ABS blends compatibilized with one MMA-MA copolymer. This copolymer has PMMA segments that appear to be miscible with the styrene-acrylonitrile (SAN) phase of ABS and the anhydride groups can react with amine end groups of the nylon 6 (Ny6) to form graft copolymers at the interface between Ny6 and ABS rich phases. Tensile and impact and morphological properties were enhanced by the incorporation of this copolymer. Transmission electron microscopy (TEM) observations revealed that the ABS domains are finely dispersed in nylon 6 matrix and led to the lowest ductile-brittle transition temperatures and highest impact properties. It can be concluded that the MMA-MA copolymer is an efficient alternative for the reactive compatibilization and can be used as a compatibilizer for nylon 6/ABS blends.© 2003 Kluwer Academic Publishers.

Morphological, mechanical and thermal properties of nylon 6/ABS blends using glycidyl methacrylate-methyl methacrylate copolymers

Nylon6 is an attractive polymer for engineering applications because it has reactive functionality through amine and carboxyl end groups that are capable of reacting. For this reason, it has been used a lot in polymeric blends. Blends of nylon6/ABS (acrylonitrile-butadiene-styrene) were produced using glycidyl methacrylate-methyl methacrylate (GMA-MMA) copolymers as compatibilizer. The binary blends were immiscible and exhibited poor mechanical properties that stemmed from the unfavorable interactions among their molecular segments. This produced an unstable coarse phase morphology and weak interfaces between the phases in the solid state. The presence of the copolymer in the blends clearly led to a more efficient dispersion of the ABS phase and consequently optimized Izod impact properties. However, the compatibilized blend showed poor toughness at room temperature and failed in a brittle manner at subambient temperatures. © 2005 Springer Science + Business Media, Inc.

Influence of thermal and mechanical cycling on the flexural strength of ceramics with titanium or gold alloy frameworks

Objectives: The aim of this study was to evaluate the effect of thermal and mechanical cycling alone or in combination, on the flexural strength of ceramic and metallic frameworks cast in gold alloy or titanium. Methods: Metallic frameworks (25 mm × 3 mm × 0.5 mm) (N = 96) cast in gold alloy or commercial pure titanium (Ti cp) were obtained using acrylic templates. They were airborne particle-abraded with 150 μm aluminum oxide at the central area of the frameworks (8 mm × 3 mm). Bonding agent and opaque were applied on the particle-abraded surfaces and the corresponding ceramic for each metal was fired onto them. The thickness of the ceramic layer was standardized by positioning the frameworks in a metallic template (height: 1 mm). The specimens from each ceramic-metal combination (N = 96, n = 12 per group) were randomly assigned into four experimental fatigue conditions, namely water storage at 37 °C for 24 h (control group), thermal cycling (3000 cycles, between 4 and 55 °C, dwell time: 10 s), mechanical cycling (20,000 cycles under 10 N load, immersion in distilled water at 37 °C) and, thermal and mechanical cycling. A flexural strength test was performed in a universal testing machine (crosshead speed: 1.5 mm/min). Data were statistically analyzed using two-way ANOVA and Tukey's test (α = 0.05). Results: The mean flexural strength values for the ceramic-gold alloy combination (55 ± 7.2 MPa) were significantly higher than those of the ceramic-Ti cp combination (32 ± 6.7 MPa) regardless of the fatigue conditions performed (p < 0.05). Mechanical and thermo-mechanical fatigue decreased the flexural strength results significantly for both ceramic-gold alloy (52 ± 6.6 and 53 ± 5.6 MPa, respectively) and ceramic-Ti cp combinations (29 ± 6.8 and 29 ± 6.8 MPa, respectively) compared to the control group (58 ± 7.8 and 39 ± 5.1 MPa, for gold and Ti cp, respectively) (p < 0.05) (Tukey's test). While ceramic-Ti cp combinations failed adhesively at the metal-opaque interface, gold alloy frameworks exhibited a residue of ceramic material on the surface in all experimental groups. Significance: Mechanical and thermo-mechanical fatigue conditions decreased the flexural strength values for both ceramic-gold alloy and ceramic-Ti cp combinations with the results being significantly lower for the latter in all experimental conditions. © 2007 Academy of Dental Materials.