Color stability of a nanofilled resin: influence of polishing and finishing and fluoride solutions according to time

Aim: The aim of the study was evaluate the finishing and polishing effect of the color stability of the composite resin Filtek Supreme XT, according to different fluoride solutions and time. Material and Methods: Specimens were prepared (n=140) with half of the samples finished and polished. The experimental groups were divided according to the presence or absence of finishing and polishing and immersion solutions (artificial saliva, sodium fluoride solution at 0.05% - manipulated, Fluordent Reach, Oral B, Fluorgard). The specimens remained in artificial saliva for 24 hours and were subjected to an initial color analysis using a spectrophotometer CIELab system. Then, they were immersed in the experimental solutions for 1 minute a day. The readings of the color change were made after 24 and 48 hours, 7, 14, 21, 30 and 60 days after the first immersion. The three-way mixed Analysis of Variance (ANOVA) ("finishing/polishing", "immersion medium" and “time”) were performed. For multiple comparisons, the Sidak test for repeated measure was used, with a 5% level of significance. Results: The finishing and polishing factor showed significant variability, independently of the immersion media (p<0.001). Cconclusion: Finishing and polishing procedures yielded better color stability to composite resin over time, regardless of the immersion media.

Induction of multiple ovulations in mares using low doses of GnRH agonist Deslorelin Acetate at 48 hours after luteolysis

This study was aimed to test low doses of a GnRH agonist, deslorelin acetate (DA), for induction of multiple ovulations in mares and to determine its impact upon their reproductive efficiency. Seven mares aging from 8-20 years were used in three consecutive reproductive cycles. Mares were initially monitored by ultrasound irrespectively of cycle stage, inseminated and submitted to embryo collection (EC) (T1). Immediately after, mares received 7.5 mg dinoprost tromothamine (DT) and were monitored by ultrasound twice a day until larger follicle reached 23-25mm and the second >18mm (T2). At this time point, mares received 100 mu g DA and ovulation was induced with 1000 mu g DA and 1000IU hCG when largest follicle reached 33-35mm in diameter, followed by EC. Mares were further allocated to T3 when received 7.5 mg DT after EC on 12 and 100 mu g DA 48 h later. DA treatment was performed until dominant follicle reached 34 +/- 1 mm or 6 days of application. All EC were performed 8 days after ovulation. Mares with multiple ovulations in T1, T2 and T3 were 14.28% (1/7), 100.00% (7/7) and 0.00% (0/7), respectively, and averaged 0.43 +/- 0.53 in T1, 0.86 +/- 0.38 in T2 and 0.00 in T3 embryos per donor, respectively. Embryo recovery rate was 43.00% in T1, 85.71% in T2 and 0.00% T3. In conclusion, use of DA in mares with follicles larger than 25mm enhanced dominant and co-dominant follicle growth, that ultimately increased the incidence of multiple ovulations and embryo recovery rate.

Interaction between recrystallization and strain-induced precipitation in a high Nb- and N-bearing austenitic stainless steel: influence of the interpass time

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Metabolic risk and television time in adolescent females

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Characterization of the nonlinear behavior of a F-16 aircraft using discrete-time Volterra series

The linearity assumption in the structural dynamics analysis is a severe practical limitation. Further, in the investigation of mechanisms presented in fighter aircrafts, as for instance aeroelastic nonlinearity, friction or gaps in wing-load-payload mounting interfaces, is mandatory to use a nonlinear analysis technique. Among different approaches that can be used to this matter, the Volterra theory is an interesting strategy, since it is a generalization of the linear convolution. It represents the response of a nonlinear system as a sum of linear and nonlinear components. Thus, this paper aims to use the discrete-time version of Volterra series expanded with Kautz filters to characterize the nonlinear dynamics of a F-16 aircraft. To illustrate the approach, it is identified and characterized a non-parametric model using the data obtained during a ground vibration test performed in a F-16 wing-to-payload mounting interfaces. Several amplitude inputs applied in two shakers are used to show softening nonlinearities presented in the acceleration data. The results obtained in the analysis have shown the capability of the Volterra series to give some insight about the nonlinear dynamics of the F-16 mounting interfaces. The biggest advantage of this approach is to separate the linear and nonlinear contributions through the multiple convolutions through the Volterra kernels.

Machine vision and planning applied on assembby line of multiple products

This article describes the use of Artificial Intelligence (IA) techniques applied in cells of a manufacturing system. Machine Vision was used to identify pieces and their positions of two different products to be assembled in the same productive line. This information is given as input for an IA planner embedded in the manufacturing system. Therefore, initial and final states are sent automatically to the planner capable to generate assembly plans for a robotic cell, in real time.