Efeito das técnicas de fusão sobre a fluidez de ligas do sistema cobre-alumínio.

It was evaluated the castability of four copper-aluminium alloy according the melting casting method used. The specimens were made using polyester mesh screen, with 11 x 11 filaments of 0.26 mm thick, fixed along of two adjacent edges in wax bar, with the sprue attached at their junction. The alloys were in an electrical casting machine and a centrifugal casting machine with an air/gas torch. The castability values were obtained by the percentage of completed segments of the resulting cast alloy screen. It was verified that the use of the electrical casting machine produced higher castability values to the copper-aluminium alloys than those produced by a centrifugal casting machine with an air/gas torch.

Determinação de dureza de ligas de cobre, na forma como são recebidas e após a fundição, em função das técnicas de fusão.

It was evaluated the Vickers hardness of five high-copper casting alloys, in their original package form and after casting, according to the casting method used. That way, ten ingots, supplied by the manufacturers of each alloy, were included in self-curing acrylic resin, polished, numerated and submitted to Vickers hardness test at load of 200 g during 30 seconds. Afterwards the numerated ingots were removed from the acrylic resin and five of those were cast in an electrical casting machine and the other five in a centrifugal casting machine with an air/gas torch. The specimens obtained were included in self-curing acrylic resin, polished and submitted to Vickers hardness test. As a result it was verified that there is a variation of hardness among the alloys tested, and the use of the electrical casting machine produced lower hardness values than those produced when used the centrifugal casting machine with an air/gas torch. Also, there is a decrease of hardness of the cast alloys when they are tested in their original form and after casting.

Estudo comaprativo da resistência da união esmalt/resina/metal. Efeito de resinas de fixação, artifícios retentivos e ligas metálicas.

The purpose of this study was to compare the enamel/resin/metal bond tensile strength by using human canines, in which castings were bonded. These castings were obtained by Co-Cr or Ni-Cr alloys and showed four types of mechanisms of retention: 50 micrograms aluminum oxide abrasive, electrochemical etch, acrylic beads metal mesh. The castings were bonded utilizing Comspan Opaque and Panavia Ex. The specimens were subjected to tensile forces after 24 hours in an Instron machine. The castings subjected to 50 micrograms aluminum oxide abrasive and bonded utilizing Panavia EX showed the biggest bond tensile strength.

Fadiga de grampos de retenção em prótese parcial removível. Efeito de ligas, espessuras e técnicas de fusão. Parte I.

The authors looked for the verification of the fatigue of retentive clasps utilized on the removable partial denture. According to this, it was idealized and built on assay machine, that through movements, simulate the insertion and removal of the clasp for a pattern tooth, manufactured on cobalt-chromium which has all the preparation normally utilized to the correct confection of this type of prosthesis. It was utilized three different commercial alloys based on cobalt-chromium: L1-Biosil; L2-Steldent; L3-Duracron. It was utilized the T clasp of Roach, with was tested upon three different proportions among width and thickness: E1-1.7;E2-2.0 and E3-2.3 and was casted through two casting techniques: F1-oxygen-gas and F2-oxygen-acetylene. The clasps were tested on the machine, which allowed the reading of the number of insertion and removal cycles made until fatigue appeared. The obtained results were submitted to the statistic analysis and the authors concluded that: a) L3 (Duracrom) obtained the best results followed by L1 (Biosil) and finally L3 (Steldent); b) among the analyzed thickness, the best results were obtained by E3, followed by E2 and after this E1; c) form the casting techniques, F2 gave us the best results.

Fadiga de grampos de retenção em prótese parcial removível. Efeito de ligas, espessuras e técnicas de fusão. Parte II.

The authors tested the T clasp of Roach in three differents proportions among width and thickness: E1-1.7; E2-2.0 and E3-2.3, with a constant length of 15 mm. These clasps were casted with three cobalt-chromium alloys (L1-Biosil; L2-Steldent and L3-Duracrom), through two casting techniques (F1-oxygen-gas and F2-oxygen-acetylene). The fatigue of the clasps were verified by using and assay machine, that through movements, simulate the insertion and removal of the clasps for a pattern which were obtained from a premolar, prepared in a surveyor. This machine detect the fatigue of the clasps and count the number of cycles of insertion and removal realized. The obtained results of the interaction between the analysed factors, were submitted to the statistic analysis and the authors concluded that: a) the interaction of factors, Alloy x Thickness, Alloy x Casting Technique and Thickness x Casting Technique did not change the order of effects that the factors showed separately but gave rise to effects of different magnitude for any observed sense; b) the simultaneous interaction of the factors Alloy x Thickness x Casting Technique confirmed the superiority of the L3 alloy, the thickness E3 and the F2 casting technique.

Alterações histológicas de glândulas submandibulares e testículos induzidas por dietas à base de soja e dieta zinco deficiente em ratos.

The purpose of this study was to examine in rats the histologic alterations of the submandibular glands and testicles induced by soy diets and zinc deficient diet. The zinc deficiency produced testicles alterations including seminiferous tubulus atrophy, germinative epithelium degeneration, spermatogenesis alterations and a significant atrophy of the submandibular glands which presented no much delimitated acines. The soy diet without complementations also compromised the spermatogenesis by showing seminiferous tubulus atrophied and a reduction of the germinative epithelium. The soy diet complemented by saline and vitaminic mixtures didn't produced testicles alterations but its induced in the submandibular glands a hypertrophy of the ductal component mainly in relation to the granular component.

Efeito de parâmetros analíticos sobre a precisão de métodos de extração de zinco do solo

Fifteen soil samples and four extradants (DTPA, Na 2EDTA, HCl and Mehlich 1) were used to study soil extraction methods for available zinc. Each extradant was studied in three soil:solution ratios (1:2, 1:4 and 1:10) and in three extraction periods in the ratio most frequently used. The zinc extracted by DTPA, Na 2EDTA and HCl was not affected by use of soil:solution ratios 1:2 and 1:4, but the amount extracted increased with the 1:10 ratio. In this relation, the variation coefficients increased. With Mehlich, no definite tendency was observed. The increase of extraction period for DTPA extractant, in 1:2 ratio, had little effect on the amount of zinc extracted and on the precision. As to Na 2EDTA extractant in 1:10 ratio, with the increase of extraction time, both increased. As to HCl and Mehlich, both in 1:4 ratio, the increase in extraction period had no effect on the amount of zinc extracted and no definite effect on the precision. Thus, the use of 1:2 ratio for DTPA and Na 2EDTA and 1:4 ratio for acid extractants is recommended. Concerning the period of extraction, 120 min should be used with DTPA and Na 2EDTA, 15 min with HCl and 5 min with Mehlich.

Um estudo sobre a corrosão aquosa de ligas de alumínio 7xxx submetidas a diferentes tratamentos térmicos

This job aim has been to study the aqueous corrosion of the 7xxx heattreatable aluminium alloys, used in the aeronautical industry. The 7010, 7050 and 7475 alloys, have been supplied in the T7 condition and submitted to the annealed and aging thermal treatments of in order to study their behaviours front to corrosion in 5% NaCl pH 6,0, air-saturated and deaerated solutions. The electrochemical study has been accomplished through potential measures in open circuit, potentiodynamic polarisation curves and electrochemical impedance spectroscopy (EIS). The aged alloy resulted to be the most resistant to corrosion and annealed the less resistant ones. In spite of it they have different chemical compositions, in each mean, the alloy with the same thermal treatment has behaved in a similar way. In aerated solution, the process is controlled by oxygen diffusion and in oxygen absence for dissolution through a film. Hardness and mass loss measures, after corrosion test, have supported this research.

Efeito do nitrato e nitrito na corrosão das ligas de alumínio 2024 e 7050 em soluções de NaCl

The 2024-T3 and 7050-T7 aluminium alloys electrochemical behavior has been studied in NaCl 5% neutral solutions and 0,1M concentration containing NO 3 - or NO 2 -. The current job supports corrosion research on aluminium alloys used in aeronautic industry. Open circuit potential, polarisation curves and electrochemical impedance spectroscopy techniques have been used. In chloride solutions, alloys corrosion takes place through a pitting mechanism. Added anions to aerated solutions do not possess inhibition effect. In deaerated solutions, nitrite has diminished anodic dissolution rate, probably by incorporating this anion in the oxide and/or hydroxide film.

Desenvolvimento de um dispositivo para obtenção de monocristais de ligas à base de cobre

This paper describes the drawing, construction and optimization of a device, which can be used to obtain single crystals of different metallic materials with melting point from 550 to 1050°C. Components of ease obtaining and of low cost were used. The device was based on the modified Bridgman technique and it was used to obtain single crystals of copper-based alloys. The temperature axial profiles and a difference less then 1% in the temperature between the wall and the center of the ceramic tube in the critical region for obtaining single crystals of good quality indicated that the oven presents a good thermal stability. Single crystals of CuZnAl and CuAlAg alloys of good quality were growth and characterized using optical microscopy and Laüe X-ray back reflection.

Papel da eritropoetina recombinante humana sobre o metabolismo dos carboidratos, paratormônio, cálcio iônico, zinco, prolactina e níveis pressóricos em renais crônicos tratados com hemodiálise

Objective: To evaluate the influence of recombinant human erythropoietin (Epho) on carbohydrate metabolism, parathyroid hormone, calcium ionic, zinc, prolactin and blood pressure (BP) in chronic renal failure treated by hemodialysis. Methods: Ten patients in hemodialysis were followed during 24 weeks in two phases: 12 weeks pre-Epho (BP was measured pre and post hemodialysis sessions) and 12 weeks post-Epho (BP was measured as above and also the blood levels of glucose, insulin, parathyroid hormone, calcium ionic, prolactin, and zinc). Results: Patients were 39.8±8.5 y, 50% males. Hematocrit and hemoglobin presented a significant increase four weeks after Epho (22.3±2.3 to 28.1±2.6% and 7.4±0.8 to 9.4±0.9 g/dL, p<0.05). BP (mmHg) and weight pre-Epho: 158±99 and 59±13 (before hemodialysis), 147±96 and 55±13 (after hemo) and post-Epho: 161±100 and 59±13 (before hemo) 155±101 and 56±12 (after hemo) were all not statistically different in any moment. There are also no difference pre and post-Epho in fast glucose (91.8±6.5 and 90.8±6.1 mg/dL, p>0.05), parathyroid hormone (341.4±249.3 and 515.7±310 pg/ mL), calcium ionic (3,66±0.63 and 3.76±0.45 mmol/L), prolactin (males: 327±144.1 and 298.1 ±145.2 μg/mL; females: 666.2±426.6 and 659±395.3 μg/mL) and zinc (median of 0.73 and 0.71 μg\L). Basal insulin was lower after Epho (median of 9.1 to 3.8 μg/mL, p<0.05). Conclusion: These data suggest that recombinant human erythropoietin was effective to improve the anemia and the carbohydrate metabolism in patients with chronic renal failure treated by hemodialysis. © Copyright Moreira Jr. Editors. Todos os direitos reservados.

Efeito residual de calcário, nitrogênio e zinco na produção de matéria seca de Brachiaria decumbens em condições de campo

The balance of liming and fertilization practice with nitrogen and zinc could affect the production of the pasture. Thus, the present work has as objective to evaluate the residual effect of the application of calcareous rock, nitrogen, and zinc on the dry matter production of Brachiaria decumbens, during three cuts. For this, an experiment was installed in Selvíria, Brazil, on a distrofic red Latosol, from october 1997 to may 1998. The experimental design was randomized blocks, in a factorial project 3×3×2, with four repetitions. The treatments were three doses of nitrogen: 0, 50, and 100 kg/ha, three doses of lime: 0, 267, and 556 kg/ha, corresponding to 41, 50, and 60% of the levels of base saturation, respectively, and two doses of zinc 0 and 5 kg/ha, applied in the first year and reapplied in the second year, except for the limestone. Four cuts were done in the grass at 10 cm of height, with intervals of 49 days, to obtain the dry matter production. The limestone application in the first year did not provide to residual effect on the production of Brachiaria decumbens. However, the nitrogen fertilization increased the dry matter production of the grass. The application of zinc in the first year and the reapplication in the second year did not result in a productive response of B. decumbens. © 2009 Instituto Nacional de Investigaciones Agricolas INIA.

Desenvolvimento e nutrição do capim-Tanzânia em função da aplicação de zinco

It was aimed to assess the effects of zinc in the development and nutrition of Tanzania grass. The experimental design used was fully randomized, consisting of six doses of zinc (0, 15, 30, 60, 120 and 240 mg dm'3) and four repetitions. The experimental unit was formed in a vase filled with a Red Latosol dystrophic (Zn = 0.4 mg dm). There were two cuts, the first after 53 days of transplanting seedlings and the second 35 days after the first cut. Was evaluated the concentration of zinc in the soil, the content of zinc leaf, the number of tillers, number of leaves, plant height, the dry mass of the shoot, root system and the whole plant. The doses of zinc influenced the concentration of zinc in soil and plant, and production of dry mass of Tanzania grass, especially the first cut. The Tanzania grass shows high tolerance to the toxicity of zinc, and toxic critical level of 273 mg kg-1.

Alimentação de leitões com dietas contendo soro de leite fermentado mais zinco e cobre orgânico

An experiment was carried out to evaluate the performance of piglets fed rations containing fermented milk and zinc and copper amino acid complex. Sixty four piglets, littermates, were used. The experimental design was based on random block with two dietary treatments. One of these contained a basal diet (DB) with ZnO e CuSO 4 and the other one with the DB, but without CuSO 4 and with the addition of fermented milk and zinc and copper amino acid complex (SLF Lact +ZnCuAA). There were eight replicate pens per treatment, and pigs were grouped at 4 per pen. The SLF Lact + ZnCuAA didn't not affect (p>0.05) final live weight of the piglets. However, live weight was different (p<0.01) between males and females (24.3 vs. 24.0 kg) at end of experiment. The feed intake of animals feed with SLF Lact+ZnCuAA was higher (p<0.01) in 8% in the first 14 days (0.261 vs. 0.239 kg/d), 15% from 15 to 28 days (0.756 vs. 0.675 kg/ d) and 12% from 29 to 42 days (1.091 vs. 0.962 kg/ d) compared to control group. Daily average feed intake in the experimental period was 11% higher (p<0.01) for the animals fed with the diet contained SLF Lact+ZnCuAA. Weight gain of the treatment with SLFL act+ZnCuAA was higher (p<0.01) by 14% from 0 to 14 days (0.176 vs. 0.152 kg/d), 11% from 15 to 28 days (0.564 vs. 0.500 kg/d) and 12% from 29 to 42 days (0,572 vs. 0,501 kg/d). Average daily weight gain of 42 days of trial of treatment with SLF Lact +ZnCuAA was 12% higher (p<0.01) compared to control group (0.437 vs. 0.384 kg/d). Feed conversion ratio was 8% lower (p<0.01) for treatment with SLF Lact+ZnCuAA in the first 14 days (1.487 vs. 1.614). Supplementation with fermented milk and zinc and copper amino acid complex in diets containing zinc oxide improved growth performance of weanling piglets.

Doses de zinco e nitrogênio na produtividade e qualidade de grãos de ervilha

Peas present a potential to be cultivated in the winter, in Brazil, and also a great importance, especially in human feeding, due to its high protein content. However, its yield is still low and there are just a few studies aiming at improving pea grains quality and yield. This study aimed at evaluating the nitrogen and zinc fertilization effect on the pea grains (Utrillo cultivar) chemical quality and yield. The experiment was carried out in a dystrophic clayey Latosol-Haplustox, in Selvíria, Mato Grosso do Sul State, Brazil, in 2005. A randomized blocks design was used, in a 4×4 factorial scheme, totaling 16 treatments and 3 replications, including four nitrogen doses (0 kg ha-1, 60 kg ha-1, 120 kg ha-1, and 240 kg ha-1), as urea, via ground, at 30 days after sowing (DAS), and four zinc doses (0 kg ha-1, 1,5 kg ha-1, 3 kg ha-1, and 6 kg ha-1), as zinc sulphate, via leaf, at 45 DAS. The combination of zinc and nitrogen doses improved the grains chemical quality. Zinc had no effect on grain yield, however, high nitrogen doses negatively affected yield.