Produção e caracterização físico-mecânica do compósito cimento-madeira com variação granulométrica dos resíduos lignocelulósicos

The need to reduce environmental damage and add value to waste causes more and more new alternatives appear to unite these two points. One of the main ways to achieve this in timber industries and the use of waste for making panels. This work was aimed at studying the influence of particle size and density in Eucalyptus mechanical compressive strength of cement composite wood. For this study was performed production and physico-mechanical characterization of specimens, using portland cement, water and waste eucalyptus. The methodology consists of a statistical study of the results obtained by calculating the density and axial compression tests and a subsequent comparison of these results with other studies. The results showed that there are significant differences in density and compressive strength when using different particle sizes the particles of eucalyptus. In general, the smaller the particle size, the lower the compression strength and the greater the density when the samples are produced with the same trait

Caracterização físico-mecânica de elementos estruturais roliços perfilados de Amaru

The study of physical and mechanical properties of wood is essential for its structural use and it is of great importance to the construction industry. Thus, this study aimed to determine the physical and mechanical properties of the wood Amaru - a hybrid of Eucalyptus, developed by Plantar Projects and Forest Products Ltda. In order to determine the properties of Amaru, round samples were used, which were provided to the Laboratory of Wood and Wooden Structures of the School of Engineering of São Carlos, University of São Paulo - LaMEM / EESC / USP. For the characterization of the physical properties, the apparent specific gravity and moisture content of the samples were determined. To the mechanical characterization, the following properties were evaluated: strength and stiffness in compression, strength and stiffness in bending, shear and tension. The procedures of the tests performed in this study were done according to the recommendations of the Brazilian Wood Standard ABNT NBR 7190:1997. The specimen used were confectioned in actual dimensions, according to as those used in the construction system proposed by Plantar. The results obtained from the tests performed showed that the mechanical properties approached the values proposed by the Wood Standard NBR 7190. The visual grading was important to provide a primary idea about the failure modes to be obtained from the tests performed. The bending test showed the modulus of elasticity (MOE) and Modulus of Rupture (MOR), which resulted in 15822 MPa and 101,7 MPa, respectively. The compression test resulted in values Ec0,m and fc0, 15698 MPa and 50,7 MPa. The tensile strength (ft0) of this hybrid was calculated and its value obtained was 60,8 MPa. The shear strength (fv0) was 8,2 MPa. The results obtained from the tests are the basis for engineers and architects to design structures using wood species Amaru

Plano de iluminação externa da UNESP Campus Itapeva com base em LED e energia solar

This work presents the development of the External Lighting Plan UNESP in the Itapeva Campus based LED and Solar Energy. Firstly it was made a collection of data from measurements of the local transit through the Google Earth 6 software and divide the local in sectors, and then perform an analysis of characteristics and age of the site. With these data it was possible to determine the average luminance the place, in30 lux. After these procedures was possible to determine the type of sets that would perform the role of bridge lighting the kit chosen was the 20/20 Sun LED manufacturer, since it contains the luminaire with the solar panel to the pole. Therefore we determined the number of poles for each sector, whichwas72in total and. After the determination of the location of each point lighting

Estudo da concentração de material particulado em ambientes internos e externos de bibliotecas

Our twenty-first century society and the rhythm of life and work we have to face in our daily routine compel us to spend most of our lifetime in closed environments, in our houses, educational institutions, hospitals, airports, amongst as many others. The study of the air quality in internal environments (IAQ) is very important for monitoring people’s health effects and their environmental comfort in these locations. One essential parameter to analyze this measure is to evaluate the concentration of dispersed particulates in the air, specially focusing on those thinner particles (below the diameter of 2,5 μm), they can pose serious risks for human being because they can remain in the lungs, penetrate through the pores of our skin, amongst other harmful effects on human’s health. In this work the air quality inside the public library Profª Josina Vasques Ferrari and at Unesp public state library was evaluated, both located in Itapeva, as well as a third one, inside the Communitarian Library of the Federal University in Carlos (UFSCar) from march to may in 2012. In those environments it was analyzed if the concentration of particulates pose any real treat to the users. The equipment used for particle sampling in real time was DataRam 4 (Model DR 4000). The results given for those concentrations of particulates in both internal and external environments revealed figures within the safe standard established by the WHO (World Health Organization), from 25 to μg/m³, the only exception occurred on the fifth floor of the UFSCar library, where the average for concentration stayed at 25,30 of μg/m³

Estudo de caso de controle estatístico de processo: levantamento da variação de espessura de tábuas de pinus

This graduate work approaches the study of Statistical Process Control - SPC, in a stage production of an industrial frame, aiming to use the tool of statistical process control (SPC) to assess the process capability. Where the process needs improvement as well not meet the specifications. Assessing the needs that the company needs to improve quality management, and the difficulties they present during the implementation of the CEP. The present study is to use the method of case study. The results are presented through study, and checking the capacity and stability of the process using control charts XbarraR. The process demonstrated the need for improvements in process and quality management. At the end of the work are presented suggestions for improving the quality system of the company

Análise da influência da concentração de feixeis de fibras de bambu em ensaios de piso

Bamboo has one of the highest growth rates among plants, however, its lignifications (which confers resistance) takes around a few years and, therefore, certain physical characteristics and mechanical, that depend on this process will only be acquired between the three to six years old. In addition, bamboo also has significant density variations in different parts of the stem, both in the radial direction as the axial. In particular the radial direction, where the density found in the inner and outer (near the bark) of a single stem can range on average from 0.5 to 0.9 g/cm3. Thus, the application of bamboo as a floor, there to examine whether both sides of the bamboo (internal and external), provide resistance properties required for that purpose. In this study sought to characterize and quantify the influence of the concentration of fiber bundles in the inner and outer sides of rules or bamboo strips of bamboo flooring through testing service. Analyses performed were based on ASTM D 2394- 83 for wooden floors and derivatives. This was necessary because of the absence of a specific prohibition of the use and testing of floors made of bamboo and its products. The data were analyzed by ball indentation test shooting, test for resistance to abrasion, indentation test for stress / load treadmill test and by indentation loads applied to small areas - test the jump. The results of the tests were extremely friendly bamboo, even this presents considerable differences between the resistances obtained from assay of the cover of the inner and outer face, being comparable with those of many commonly used to manufacture wood flooring. This comparison was made possible by information from technical trials of several floors made with wood

Viabilidade do aproveitamento de resíduos de madeira para produção de móveis

The need to use waste from wood processing industry grows due to environmental demands imposed by laws, so like the need to introduce more competitive products in the market (it means better quality and acceptable cost) who must submit by the rational use of raw material, usually turning waste to sub products, what adds higher value for that. To this research, specific case from Ribon Company, located on Camaçari, Bahia-Brazil, has been studied. It is a treated wood producer. Bulk of monthly wood logs there is 70 m3. Its yield is 71,43%, where bulk of generated waste is monthly 20m3. As an exploitation way from generated waste, it has been suggested some options like: erosion protection to specific areas, a wildlife shelter as an henhouse etc, recreational articles, coal, linings, treadmills. However this research will give focus to the furniture design made of waste. As a conclusion, there is very much need to assign new utilizations to that sub used materials, since there is significant amount to increase company’s productive yield

Análise do consumo de energia elétrica e da eficiência energética em uma indústria de processamento de madeira

In the industries of wood processing (sawmills), where timber is sawn in equipment such as band saws, circular saws, trowel, thicknessers, among others, that mechanically transform this resource and use of electric motors, which are not unusually poorly scaled working or overloaded, often a factor that is not found in these industries and has fundamental importance in the production process is energy efficiency that is achieved by both technological innovation and through all the practices and policies that aim to lower energy consumption, lowering energy costs and increasing the amount of energy offered no change in generation. For both during the design of an electrical installation, both overall and in various sectors of the installation, investigations are necessary, considerations and uses of variables and factors that put into practice the theme of energy efficiency. Therefore, in this paper, these factors were calculated and analyzed for a wood processing industry (sawmill) in the municipality of Taquarivaí - SP, namely: active power, power factor, demand factor and load factor. Where they were small in relation to the literature, these events that occur when devices are connected at the same time and due to the conditions of processing the wood, where the engines have large variations in electricity consumption during the unfolding of the same, due to efforts with the load and idle moments between each machining operation in the equipment

Estudo de compósitos de madeira com reforço em bambu para utilização em mobiliário

Bamboo has been studied because of its peculiar mechanical properties and numerous possibilities of use, besides being a fast-growing grass and short cutting cycle. This study aimed to analyze the mechanical characteristics of wood-bamboo composite material, where the samples were developed from the combination of layers of bamboo as a structural reinforcement in solid pieces of pine and EGP panel parts. The species of wood used was Pinus taeda, and the bamboo species Guadua angustifolia and Dendrocalamus giganteus. All work was conducted at the Universidade Estadual Paulista - UNESP in the laboratory of Physical and Mechanical Properties of Wood. Tests including the density and tension parallel to grain of the bamboo species used and the static bending of composites in order to use this in the furniture industry. For the tests have been used as a basis the requirements of the normative document NBR 7190/97. The values obtained in the tests showed a significant increase in strength and stiffness compared to unreinforced parts, where there was an increase in MOE and MOR in static bending in all specimens used in evidence. The results showed the possibility of reducing sections in furniture components and the possibility of improving the mechanical properties of parts with defects found in wood of Pinus Itapeva region of São Paulo

Estudo de caso do conforto térmico de dois modelos construtivos em madeira: wood frame e log home

O presente trabalho consiste em demonstrar valores referentes ao conforto ambiental de dois modelos construtivos, sendo o primeiro um edifício já executado e o outro em fase de implantação, ambos no Campus Experimental de Itapeva, aplicando alguns conceitos em habitação mais sustentáveis de madeira na região de Itapeva, estado de São Paulo, Brasil. A edificação construída sedia duas salas de aula a partir da tipologia construtiva wood frame, constituída basicamente de paredes autoportantes compostas de ossatura de madeira tratada de pinus.sp, chapas estruturais em OSB, manta de isolamento térmico/acústico e fechamento interno e externo, respectivamente em gesso e sidding (lambris de madeira). A habitação em fase de início de implantação foi idealizada a partir da tipologia construtiva log-home, e atenderá a necessidade de espaço físico para abrigar o Centro Acadêmico e a empresa-júnior “PROMAD”, ambos do curso de Engenharia Industrial Madeireira do Campus Experimental da UNESP/Itapeva. Esta construção foi elaborada a partir de técnicas de baixo impacto ambiental, levando em consideração os resultados de análise térmica obtidos na edificação anterior. Em ambos modelos construtivos foram empregados recursos renováveis abundantes na região, como a madeira de reflorestamento de Pinus e de Eucalipto. Foi acrescentado ainda ao segundo modelo a utilização de resíduos industriais lignocelulósicos, como rolete de laminação e outros materiais locais disponíveis. A metodologia básica empregada para a obtenção de dados sobre o conforto térmico em relação as edificações foi, para o primeiro caso, a coleta de dados de temperatura e umidade utilizando um termo-higrômetro, a sistematização e análise de dados reais obtidos no interior da edificação. No segundo caso, o dimensionamento do conforto térmico... (Resumo completo, clicar acesso eletrônico abaixo)

Estudos exploratórios sobre propriedades térmicas do compósito cimento-polpa celulósica(CPC)

The search for a more aware use of available raw materials has led to a need to create more sustainable products. The use of natural fibers to reinforce cement, for instance, has been widely studied in the past decades because of the possibility that they can improve material properties such as thermal resistance and to compression, besides conferring a decrease in their total weight. This present study aimed at to conduct preliminary studies on the thermal resistance of the composite cement - Cellulose Pulp, using waste from the pulp and paper industry. Through experiments, it was found that the composite manufactured using the ratio 30 % Portland cement and 70 % pulp, showed satisfactory results regarding its thermal resistance, so it could be considered as a potential thermal insulation material, for use in constructions

O design industrial e as engenharias: uma possibilidade de integração por intermédio da engenharia reversa

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Variáveis biométricas da cana-de-açúcar fertilizada com resíduos orgânico e industrial e irrigada com água servida e potável

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Produtividade e qualidade industrial do arroz de terras altas em função da disponibilidade hídrica e adubação

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Características físicas e fisiológicas na qualidade industrial de cultivares e linhagens de trigo e triticale

The physical, physiological and rheological characteristics of cultivars and lines of wheat CD (COODETEC) 103, 104, 105, 107, 108, 109, 110, 111 and CD 2017 and CDFAPA 2036 lines and triticale (EMBRAPA 53), for quality of flour for bread making were studied. The weight of hectliter (HW), weight of thousand grains (WTG), percentage of germination, total protein and farinography, in a completely randomized experimental design, with four repetitions, except the farinography (with two repetitions) were analyzed. The means obtained were compared by the Scott Knott test at 5%. The cultivars were different regarding the tested parameters. The PH value were compatible for commercialization, but not always the higher PH value corresponded to the greater weight of thousand grains. Only the CD 108 and 111 cultivars may be destine for French bread considering the stability parameter. About the index of tolerance for the mixture, the cultivars and lines were not different, but only the flour of 2017 line would attend the values that were established for French bread-making and fermented cookies. The CD 104, 108 and 11 cultivars and the CD 2017 and CDFAPA 2036 line obtained the ideal index also for fermented cookies. The cultivars which presented better weight of thousand grain gave the best index of tolerance for the mixture. There was no positive relation between total protein and the farinography.