A nature-inspired approach to speed up optimum-path forest clustering and its application to intrusion detection in computer networks

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Computer graphics applied to anatomy: a study of two bio-cad modeling methods on finite element analysis of human edentulous hemi-mandible

Modeling is a step to perform a finite element analysis. Different methods of model construction are reported in literature, as the Bio-CAD modeling. The purpose of this study was to perform a model evaluation and application using two methods of Bio-CAD modeling from human edentulous hemi-mandible on the finite element analysis. From CT scans of dried human skull was reconstructed a stereolithographic model. Two methods of modeling were performed: STL conversion approach (Model 1) associated to STL simplification and reverse engineering approach (Model 2). For finite element analysis was used the action of lateral pterygoid muscle as loading condition to assess total displacement (D), equivalent von-Mises stress (VM) and maximum principal stress (MP). Two models presented differences on the geometry regarding surface number (1834 (model 1); 282 (model 2)). Were observed differences in finite element mesh regarding element number (30428 nodes/16683 elements (model 1); 15801 nodes/8410 elements (model 2). D, VM and MP stress areas presented similar distribution in two models. The values were different regarding maximum and minimum values of D (ranging 0-0.511 mm (model 1) and 0-0.544 mm (model 2), VM stress (6.36E-04-11.4 MPa (model 1) and 2.15E-04-14.7 MPa (model 2) and MP stress (-1.43-9.14 MPa (model 1) and -1.2-11.6 MPa (model 2). From two methods of Bio-CAD modeling, the reverse engineering presented better anatomical representation compared to the STL conversion approach. The models presented differences in the finite element mesh, total displacement and stress distribution.

Evaluation of the Computer-based Battery for Oral Language (BILOv3) through the Rasch model for a Brazilian Sample

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

An esthetics rehabilitation with computer-aided design/ computer-aided manufacturing technology

This paper describes a case of a rehabilitation involving Computer Aided Design/Computer Aided Manufacturing (CAD-CAM) system in implant supported and dental supported prostheses using zirconia as framework. The CAD-CAM technology has developed considerably over last few years, becoming a reality in dental practice. Among the widely used systems are the systems based on zirconia which demonstrate important physical and mechanical properties of high strength, adequate fracture toughness, biocompatibility and esthetics, and are indicated for unitary prosthetic restorations and posterior and anterior framework. All the modeling was performed by using CAD-CAM system and prostheses were cemented using resin cement best suited for each situation. The rehabilitation of the maxillary arch using zirconia framework demonstrated satisfactory esthetic and functional results after a 12-month control and revealed no biological and technical complications. This article shows the important of use technology CAD/CAM in the manufacture of dental prosthesis and implant-supported.

Computer simulation of configurational properties of partially ionized polyelectrolytes

Monte Carlo simulation methods were used in order to study the conformational properties of partially ionized polyelectrolyte chains with Debye-Hückel screening in 1:1 electrolyte solution at room temperature. Configurational properties such as the distributions of probability for the square end to end distances, for the square radii of gyration and for the angles between polyion bonds were investigated as a function of the chain ionization and the salt concentration. © 1993.

Evolutionary stages of environmental management in computer companies located in Brazil: case studies

This study aims at identifying which environmental management practices computer companies located in Brazil are adopting, and classifying these companies according to the evolutionary stages of environmental management. For such, the case study research method was used at three companies. Results show that environmental management in the sector is geared towards compliance with laws and eco-efficiency, aimed at cutting costs. It was concluded that classification does not occur in a linear manner with defined borders, and that the multinational companies located in Brazil are greatly influenced by their foreign head offices, which are at more advanced evolutionary stages.