Analise da postura pela fotogrametria em escolares

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Analise do aproveitamento do glicerol no mercado brasileiro

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Analise exergoeconômica aplicada a microgeração em condomínios residenciais

Pós-graduação em Engenharia Mecânica - FEG

Introdução e aplicação da diluição da precisão das ambiguidades GNSS - ADOP

The main topic of this paper is the Ambiguity Dilution of Precision known as ADOP. Basically, ADOP is defined as a diagnostic measure for assessing the precision of the float scalar ambiguities. Among the several possibilities, the ADOP can provide help in predicting the behavior of a baseline or a network of GNSS receivers, concerning the problem of ambiguity resolution, either in real-time (instantaneous) or in the post-processing mode. The main advantage of using ADOP is possibility of the extraction of a closed analytical expression, considering various factors that affect the ambiguity resolution. Furthermore, the ADOP is related to the success rate of ambiguity resolution. The expressions here used, takes into account several factors, for example, a priori information of the measurement precision of GNSS carrier phase and pseudorange, the number of stations and satellites, the number of available frequencies and the behavior of the atmosphere (ionosphere and troposphere). Several scenarios were established so as to analyze the impact of each factor in ambiguities resolution, within the context of some stations of the São Paulo GNSS network (GNSS-SP).

Wilsonismo e mudanca: analise da abordagem wilsoniana na politica externa das administracoes Bill Clinton e George W. Bush

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Proposta construtivista em questão: analise da experiencia brasileira no ensino da leitura e escrita

Years after the constructivism theory was adopted by “Parameters for National Syllabuses”, the results have pointed to a worse performance in teaching and learning with regards to reading and writing. This article presents the conclusions proceeding from investigation about the probable reasons for the student’s lack of success in reading and writing, and its relation to Emília Ferreiro’s constructivism proposals. Interviews were made as well as sit in class observation were done, with twenty teachers at six Fundamental Level 1 schools in Ourinhos, SP State, in schools that had been awarded the best and the worst performance rating in the Prova Brasil-2005, with this objective: to know and analyze the teacher’s conceptions under their practices and their practices in the classes. The conclusion is: it is not possible to attribute the students’ lack of success in reading and writing; these studies showed that many teachers, most of them, have a non-constructivist concept of teaching and learning, it means that they do not apply Ferreiro’s researches.

Analise do fator dinâmico nas fórmulas de Janbu e Hiley com base em resultados de CAPWAPC

This study aimed to evaluate the dynamic factor applied to the results obtained by dynamic resistance formulas Janbu and Hiley, would lead to the results obtained by static strength analysis CAPWAPC ®. The evaluation was done by backcalculation dynamic loading tests (ECD), taking into consideration the type of soil in which the cutting base precast concrete were settled, and using the information on the effective energy transmitted to the stakes by hammers, obtained by CAPWAPC ®. The results are shown in tables and graphs, and showed that the use of these formulations and their dynamic factors can become an efficient and economical field, assisting the engineer in making decisions regarding the staking of the work

Estudo e analise dos sistemas de proteção em subestações automatizadas de energia elétrica

Electrical energy is present in the lives of all people and is extremely important that it be delivered to end users with plenty of quality, safety and low costs. The electric power substations are responsible for transmission and distribution of electricity generating sources to consumers, and with technological advances and the subsequent automation of same, the electricity began to be delivered with greater continuity and reliability. Protection systems in substations are largely responsible for making the electricity reaches the final consumer with quality, since their function is to prevent the spread of any type of failure occurred at any point of transmission to the load centers. These systems consist primarily by the current transformers and potential, by the protective relays and circuit breakers and switchgear. The processors send the necessary data to the relays and, if those detect any abnormality in the system, operate the opening command of the branch circuit breakers to isolate where the fault. Therefore, it is essential to better understand the operation of such equipment, as well as the overall system. This work aims to study the main substation equipment, current transformers and potential and, especially, protection relays, in order to obtain the advantages that automated systems can provide

Analise técnico-econômica de um gaseificador Downdraft e de filtros para limpeza de gás de síntese

The biomass gasification systems have been used for a long time and prove to be a good alternative to the generation of energy problems. This type of management requires a simple installation and maintenance which gives them a high availability. In Biomass project via Call CTEnerg 33/2006-1, funded by the Ministry of Science and Technology - MCT - Brazil, the Group Energy Systems Optimization – GOSE - at FEG - UNESP built and tested two prototypes of gasifiers. These is fed with 25 kg / h of dry wood (chips), and 50 Nm3 / h of air to produce gas at a flow rate of approximately 70 Nm3 / h of wood (syngas) at a temperature approximately 600 ° C. In this work of graduation, studies were conducted on the materials used in both the gasifier as well as cleaning the filter synthesis gases. The system of gas cleaning and conditioning is vital to ensure the life of the Internal Combustion Engine. In this case the studies of different filters for small gasification systems (properties, materials used, characteristics, types, etc.) are very relevant to its use in the prototype of the college campus. Were also performed a technical and economic analysis of a cogeneration system that consists in the combination of the downdraft gasifier studied in this work, an internal combustion engine, two heat exchangers and a SRA (absorption system refrigerator). Were calculated the costs of electricity generation, hot water and cold water. Finally, we analyzed the economic feasibility of the project

Analise dos esforços de laminação no dimensionamento de um laminador de bancada

The industry produces rolled, starting to and passing through casting forming processes, for example, in the case in question the rolling. A large portion of rolled products are flat, these have specific characteristics during their production and properties after finished that must be analyzed. For this a study of these properties must be made in materials samples, in order to be able to first know the material in question or provide new properties to the material through the process of rolling flat products. In this way is interesting that the students of mechanical engineering have knowledge of rolling trials, and from this can better understand the behavior of rolled. With this purpose the project of a benchtop rolling mill for the rolling of flat is needed, this work is the project of a sizing of one rolling mill non-ferrous materials

Analise do sistema de medição em peças aeronaúticas através do estudo de R&R (repetibilidade e reprodutibilidade)

The Measurement System Analysis (MSA - Measurement System Analysis) is a statistical methodology developed to study and analyze the behavior of the measurement systems, and, therefore, allow the increased of the confidence readings performed by measuring instruments. It’s widely used in the automotive industry since the 90’s and is a mandatory requirement for the approval of the parts according to ISO Standard of the automotive sector. However, the aerospace industry doesn’t require this type of Study, once which the vast majority of aeronautics parts have characteristics (dimensions) with very tight tolerances, closed, ie, at the home of microns. This work aims to create lists of recommendations for definitions of measuring instruments in developing of control plans, which correlates tolerances fields of characteristics for different settings and acceptance of the instrument, classified as optimum, recommended and not recommended, through of the study of R&R (Repeatability and Reproducibility) in aeronautics parts. Every methodology of the experimental part was based on modern strategy of continuous improvement, the DMAIC (Define Measure Analyze Implant Control), in order to achieve better measurement method used in the control of milling aeronautics parts, identifying and reducing the variations of the measurement process. The results of the R&R Study in large part of measuring instrument manuals were considered acceptable and/or recommended, ie with values of %P/T and %RR lower than 30%, providing statistical data which have enabled the elaboration of tables of recommendations, which, from this work, have turned into very important documents and aid for Process Engineering, having in their hands a technical study able to identify which is the most appropriate instrument to get a more robust dimensional... (Complete abstract click electronic access below)

Analise de defeitos em motores através de vibração mecânica: estudo de caso

Revolving machines are among the most used equipment in general industry and therefore expenditures on this equipment class are a significant portion of the total amount spent by the company. If there is an unscheduled stop of some of this equipment, industrial plants can lose huge amounts of money caused by interrupted production and parts delay. Others may increase significantly maintenance costs due to consequences elsewhere not affected before. Even plant and people safety can be in danger if there is an operation interruption without a backup system start. This work is focused on a rotating system case study which is monitored by vibration analysis that shows that is possible to determine when is the most appropriate time for equipment intervention without any reliability loss just by using a simple and cheap system which is not much used because professionals are not aware to its utility. Industrial facilities were evaluated by fail detection and historical analysis in some equipment in order to show feasibility of vibration analysis through a before-during-after process. The plant evaluated is part of a chemical multinational located in Guaratinguetá-SP. At this time, that plant had around 650 critical equipment monthly monitored and no unscheduled shutdown was registered in one year period due to equipment monitoring

Estudo analise e exemplo de aplicação de geração eólica

Brazil economic growth has to predict the need for implementation of new energy sources to ensure the continuity of the economic growth and improvement of life of the brazilian population. Until this moment, this assistance included the construction of large hydroelectric plants, mainly in the amazon region, where the environmental impact is difficult or, as in the case of the Belo Monte made this impossible so far, the implementation of these projects. In this work is conducted a study that demonstrates an example of application of wind energy, through an assessment of wind resources in the brazilian Northeast for the implementation of a wind farm

Analise mecânica e microestrutural em estruturas tubulares aeronáuticas soldadas de aço ABNT 4130

Airplane Motor Cradles have a complex geometry, since they require different conbinations between different tubes and TIG welded in several angles. In T-25 aircraft and Universal T-27 Tucano (EMBRAER / FAB), besides having to bear the engine balance, these components maintain fixed the nose landing gear in another extremity. They are considered critical to flight safety, and for this reason, the aviation standards are extremely rigid in their production, imposing a zero index” of defects on the final weld metal quality. These structures may be containing an historical of welding repairs, whose effects on their structural integrity are not computed. In this work we analyzed the standardised AISI 4130 steel and the raw steel of tubes to the Airplane Motor Cradles. First of all, microscopy and microanalysis of the base steel, then we analyzed the effects of the TIG weld. Tensile testing was conducted to measure the difference between the mechanical properties of standardised steel and without this treatment